AI View S500 User manual

Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
Ultra zoom Speed Dome
AI Security Camera

Model: S500
Product Number: 0233
INSTALLATION GUIDE

PRODUCT KIT
Wall BracketCamera
3
24VAC power supply
Installation guide Drilling position decal Thank you letter
by Bkav Corporation Thank You !
Qualcomm products contained herein are products of QualcommTechnologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registeredin the Un itedStates and other cou ntries.
The Made with Qualcomm Technologies logo is a trademarkof Qualcomm Incorporated.
Ultra zoom Speed Dome
AI Security Camera
WALL DECAL FOR
DRILLING POSITION
Ø10 mm, 4 holes

Safety cable Hex toolSet 4 of screws
and anchors
4
PRODUCT KIT

5
AC 24V/3A
TECHNICAL SPECIFICATION
Power supply
Protection standards IP66, IK10
Resolution, frame rate FHD 1920x1080, 60 fps
Optical zoom 33x
Focal length 4.5 - 148.5mm ± 5%
Angle of view (horizontal-vertical) Near: 60.1° - 36.2° / Far: 2.28° - 1.29°
Environmental conditions
Dimentions (L x W x H) L380 x W290 x H450mm
9kgWeight
-40°C - 80°C (-40°F - 176°F)
Humidity 10 - 100%
Mirco SD card External, up to 256GB

PRODUCT OVERVIEW
Camera body
24VAC power supply
RJ45 terminal block
Camera lens
Infrared LED
6

INSTALLATION GUIDE
21
Step 1: Fix the camera on the bracket and tighten the screws it in the place (Figure 1).
Step 2: Assemble safety cable into the camera (Figure 2 - 3).
7
Safety cable

43
8
INSTALLATION GUIDE
Drilling position decal
Step 3: Apply positions decal and drill 4 anchors to the wall. Fix the camera onto the wall with the screw (Figure 4).

CONNECTING THE SIGNAL WIRE
Connect network signal and power 24VAC.
Network cable RJ45 terminal block
24VAC power supply Black wire
Red wire
9

CAMERA FIELD OF VIEW
90°
360°
10

ATTENTION
11
During a power outage, the camera will be down as shown in the image above.
When power is on, the camera will return to its previous position.
Note:

12
THE MEMORY CARD AND RESET INSTALLATION
Power off the camera, press and hold the factory reset button. Continue to hold the factory reset button
for another 10 seconds while powering the camera, the camera will be restored to factory settings.
If resetting with the factory reset button is difficult to operate, we recommend resetting via WebUI.
Note:
Reset factory
Mirco SD card
Reset installation: Open the protective cover that protects the camera against dust and water to reset the device.
Memory card: Open the protective cover, you can find the location of Micro SD card.

13
ACCESSING THE CAMERA
For additional security, please do not repeat any characters in your password.
If you forget your password, you can hold the [RESET] button to return the product to its factory
settings.
Note:
Password setting
Using your web browser, access the camera's default IP: 192.168.1.168
Note: To complete the installation steps for the camera, refer to the User Manual.
The system will ask you to reset the password on your initial access.
When the "Administrator password change" window appears, enter a new password.
For passwords using eight or nine characters, you need to use at least three of the following types of
characters: uppercase and lowercase letters, numbers, and special characters.
For passwords using 10 to 15 characters, you need to use at least two of the character types.
Special characters include: ~ ` ! @ # $ % ^ & * ( ) _ - = + | { } [ ] . ? /
Administrator password change
New password
Confirm new password
For a new password with 8 to 9 digits, you must use at least 3 of the following:
uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15
digits, you must use at least 2 types of those mentioned.
For higher security, you are not recommended to repeat the same characters or consecutive
keyboard inputs for your passwords.
If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose
your password by using a memo pad or memorizing it.
Special characters that are allowed: ~`!@#$%^*()_-+=|{}[].?/

Login screen
When accessing the camera, a login window will appear.
Enter your user name and password to access the camera.
1. Enter "admin" in the <User name> box.
2. Enter your chosen password in <Password> box.
3. Click
SOFTWARE INSTALLATION
14

15
SAFETY INFORMATION
Be sure to follow this advice to ensure the device works properly.
It is recommended to use shielded network cables (STP) during set-up.
It is recommended to use CAT5e or higher network cables.
Store the camera in a cool and dry environment.
Shield the camera from potential impact from heavy objects.
Do not install the camera on unstable pillars, brackets, surfaces, or walls.
Do not use chemicals or detergents to clean the camera or housing.
To clean, use a damp cloth.
Only use standard tools and accessories when installing the camera equipment. The manufacturer
recommends using the manufacturer's power supply equipment or a corresponding source for the
camera. Improper installation may cause damage to the product.
Contact Bkav's customer support or authorized Bkav agents if you experience any problems.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limit are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
a accordance with the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Precautions:
Use the original packaging, or equivalent, to avoid damaging the product during transportation.
Transportation

Bkav Corporation
Add: 2nd Floor - HH1 Building, Yen Hoa Ward, Cau Giay District, Ha Noi, Viet Nam
Website: www.aiview.ai
Email: [e-mail]