AIDA PTZ-X12-IP User manual

Full-HD Optical Zoom PTZ
PTZ-X12-IP | PTZ-NDI-X12 | PTZ-X20-IP | PTZ-NDI-X20 Manual
V2.0
AIDA

Table of Contents
1
Safety Guides
2
Packing List & Quick Start
3
Product Highlights & Camera Specs
5
Camera Interface & Dimension
6
IR Remote Controller
8
OSD Menu
10
Web Settings
15
VISCA Over IP
16
VISCA (RS-232) Port
17
VISCA Protocol
26
UVC Control
27
Warranty & Support
The information within this manual is subject to change at any time without prior notice*

Safety Guide
1
1.
Beforeoperation, please read allofthe instructionsinthe manualcarefully.Foryourconvenience,
please keep this manual.
2. The camera powerinput rangeis100-240VACv(50-60Hz). Ensure the power supply input is
withinthis rate before powering on.
3. Camerapowervoltage=12VDC,ratedcurrency=2A.Wesuggestyou useitwiththeoriginalpower
supplyadaptersuppliedby thefactory.
4. Please keep the power cable, video cable, and control cable in a safe place and out of
obstructions.
5. 0perationalenvironment:0°C-50°C/32°F-122°F,withhumidity levelsless than90%.To avoid
any damage,donoput orpour anythinginsidethe camera.
6. Avoid weight stress, vibration,and pressure onthe camera during transportation,storage,
and installation.
7. Do not remove the camera housing or cover. Doing so will void the warranty.
8. Donotdirectthe camera towardsstrong/intensivelight.Doingsocould cause
irreversible damageto the cameraandvoid warranty.
9. Useadryandsoftclothtocleanthecamerahousingwithaneutralcleaningagent,whenneeded.To
avoid damage on the camera lens, do not usestrong or abrasive cleaning agents on the camera
housing.
10. Donotmove thecamerabymovingthe camera head.To avoidmechanical trouble,do notrotate
the camera headbyhand.Pleaserefrain frommovingthecamera whileitis inmotion.Doingso
could cause irreversible damagetothe cameraandvoid warranty.
11. Make sure thecamera isona fixed and balanced platform. Avoid any slanted
placements .
12. Power SupplyPolarity Schematics:
Warning:
Video quality can be affected by specific frequencies of electromagnetic field.
Never grasp the head of the camera. Never move the camera by hand while is in
motion. Doing so can damage the mechanism.

Packing List
2
Dial Switch (ARM)
SW-1
SW-2
Mode
1
OFF
OFF
Updating Mode
2
ON
OFF
Debugging Mode
3
OFF
ON
Undefined
4
ON
ON
Working Mode
Dial Switch
SW-3
SW-4
Instruction
1
OFF
OFF
Reserve
2
ON
OFF
Reserve
3
OFF
ON
Reserve
4
ON
ON
Reserve
Dial Switch (USB)
SW-5
SW-6
Instruction
1
OFF
OFF
Undefined
2
ON
OFF
Working Mode
3
OFF
ON
Updating Mode
4
ON
ON
Undefined
Check the items below, when opening the package:
EA
Quick Start
- AIDAPTZ
- PowerAdapter
- PowerCable
- RS-232 Control
Cable
- USB3.0Cable
- RemoteControl
- User Manual
- DoubleSidedAdhesive
- QCCertification
- WallMount
1. Check thatallcable connectionsaresecure before poweringonthe camera.
2. DialSwitchSetting(UsedforCamera Updates):

Product Highlights
3
• ContainsanadvancedSonyProgressiveCMOSSensorproviding1920x1080UltraHDresolution.
• Wideangleopticallens:12x/20xopticalzoom
• FullHDvideooverIP,viaH.264orH.265encoding.
• Contains traditional outputs such as HDMI, SDI, USB3.0, as well as RJ-45 for RTSP/RTMP
streaming.
• Support line infunction, supporting ACC and LPCM audio coding.
• Fully adjustable camera settings, such as White Balance, ExposureSettings,and
Image Parameters.
• SupportsP0E: use asingleCAT5/6 cable to control andoutput video via theRJ-45port.
• Fastandprecise focusing performancewhenzooming or movingthe camera head.
• SmoothPTZmovements,aswellaslittletonomotorsoundwhenmoving.
• Supports10presetsviaremoteor128presetsviaRS-232oronlineinterface.
• StandardSonySerialVISCA,IPVISCAprotocol,aswellasIPVISCAoverUDP.
• Daisy chain is supported via the RS-232 input and output, controlling a maximum
of 7 cameras.
• Menu basedimageparameters,including imageflipforceiling mounted cameras.
• Remote has multiple functions, such as fast switching videoformatsand ability to
change IP address.
• Freefirmwareupdatestokeepthecameraup todatewiththelatestandgreatest!
• The USB3.0 port is compatible with USB2.0 and allows standard UVC1.5 protocol for local
control. UVC control worksseamlesslywith manywell-known conferencingsoftware.
• PTZ Menu supports both English andSpanish
• Supports NDI®| Hx transmission (PTZ-NDI-X12 and PTZ-NDI-X20) only.
Camera Specs
Video
Format
HDMI
(V 1.4)
1920 x 1080 60p/59.94p/50p/30p/29.97p/25p/24p/23.98
1920 x 1080 60i/59.94i/50i
1280 x 720 60p/59.94p/50p/30p/29.97p/25p
SDI
1920 x 1080 60p/59.94p/50p/30p/29.97p/25p/24p/23.98
1920 x 1080 60i/59.94i/50i
1280 x 720 60p/59.94p/50p/30p/29.97p/25p
USB
1920 x 1080 60p/50p/30p/25p (USB 3.0)
1280 x 720 60p/50p/30p (USB 3.0)
1280x72025p(USB3.0&2.0)
1024x57630p(USB3.0&2.0)
960 x 540 30p (USB 2.0)
640 x 360 30p (USB 2.0)
512 x 28830p (USB 2.0)
RJ-45
1920 x 1080 @ 1~60 1280x 720 @ 1~60 (Main Stream)
1280x720@1~60/1027x576@1~60(SubStream)

Camera Specs (CONTD)
4
Video Interface
HDMI (V 1.4) 3G-SDI, RJ-45, USB 3.0
Sensor
SONY Progressive CMOS Sensor
Zoom
12x or 20x 0ptical Zoom
Lens
F4.9~98mm (20x), F1.5-3.0, View Angle:61°(Far)-3.2°(Near)
Rotation Angle
Pan: -170°~+170°; Tilt: -30°~+90°
Rotation Speed
Pan: 0°~120°/s; Tilt: 0°~80°/s
Preset
Remote Controller: 10 RS-232: 128
Control Port
RS-232, RJ-45 (VISCA over IP), USB 3.0 (UVC 1.5), USB 2.0 (UVC 1.1)
Network Speed
1000M
Video Encode
H.264/H.265 (default: H.264)
Bit Rate Control
Variable Bit Rate, Constant Bit Rate
Video Bit Rate
1024kbps(min)~20480 kbps(max)
IP Protocol
IP, HTTP, RTSP, RTMP, DCHP, 0NVIF, VISCA over IP (UDP)
P0E
Supported (IEEE802.3af)
Line in
Supporting ACC audio coding
Daisy Chain
Support RS-232 serial daisy chain
Minimum Lux
0.01 Lux
White Balance
Auto/Indoor/0utdoor/Manual/ATW/0nePush/FluorescentLamp/Sodium Lamp
Exposure
Auto/Manual/Bright/Shutter/Iris
Focus
Auto/Manual
Iris
Auto/Manual
Gamma
Supported
WDR
Supported
BLC
Supported
2D Noise Reduction
Supported
3D Noise Reduction
Supported
Anti Flicker
0FF/50Hz/60Hz
Image Flip
Supported
Image Voltage
DC 12V / PoE (24W)
Dimension
220mm x 173mm x 190mm/8.66" x 6.81" x 7.48"
Net Weight
1.4kg/3.1lbs

Camera Interface
5
1. Camera Lens
2. CameraBase
3. IRReceiverPanel
4. Power/TallyLight
5. DialSwitch(Firmware)
6. 1/4"TripodScrewHole
7. InstallationHole
8. RS-232ControlPort(Input)
9. RS-232 Control Port(0utput)
10. HDMIPort
11. Line inPort
12. 3G-SDI Port
13. USB Port
14. RJ-45 Port
15. DC12VPlug
Camera Dimensions (in mm)

IR Remote Controller
6
Power
When powered on,pressing the power key enters standby
mode; Pressing it again will start up the camera and display
normally.
Freeze (No Function)
The Freeze button has no function on the PTZ.
IRT (IR Transfer/IR Pass)
Enables IR transfer. 0nce pressed, the camera will receive and
pass IR remote control signal (via VISCA IN Port).
SET 1~4 Address Setting
HoldtheSET#buttonfor3secondstosetthecamerasIRaddress.
CAM 1~4 (Camera selecting)
Pressing the CAM# button will enable IR control of the selected
camera.
Number Key (1-9)
SetPreset:To setpreset,holddownakey(0-9)andwait3seconds.
0ncecomplete,theselectedpresetwillbesaved.
Run Preset:Pressingakey(0-9)willbringup thecorresponding
savedpreset.
CLR PRE (Clear Preset)
Clear a Preset :Press CLRPRE and key (0-9)simultaneously to
remove the corresponding saved preset.
Clear all Presets: Hold down CLRPRE button to remove all
saved presets.
Learn
This buttonis usedwithotherremotebuttons.Ithas no function
when pressed alone.

IR Remote Controller (CONTD)
7
AF (Auto Focus)
MF (Manual Focus)
Limit L
Pressthiskey with theLearnkeytosetthemaxleftpositionofthe
camera.
Limit R
Press thiskeywith theLearn keyto setthe max rightpositionof
thecamera.
LMT CLR
PressthiskeywiththeLearnkeytoremovesetmaxpositions.
Bright /Bright
Focus Key (+/-)
Allows for precise focus change. Manual focus mode must be
enabled to use these keys.
Zoom Key (+/-)
0ptically zooms the camera in up to 12x.
Navigate Key (Up/Down/Left/Right)
Normal mode: Allows for the camera head to pan and
tilt. Menu mode: Allows for direction in the menu of the
camera.
OK/Home Key
Normal mode: Recalls to the home position of the camera.
Menumode:Usedtosetfunctionsinthemenuandactivatefeatures.
Video Format Keys:
While directly pointing at the camera, please hold the desired video
output button for3seconds.Ifdone properly,thePTZwill do a quick reset
to the desiredvideo output selected.
Used to enter the OSD menu of the camera

OSD MENU
8
1. W
hen the c a m e r a i s o n , p r e ss the ME N U ke y o n the I R r e mo te c o nt r o ll e r t o enter the OSD Menu .
2. A f te r ente r i ng the m a i n m en u , u s e the U P / Down nav i gate ke ys o n the c o nt r o ll e r t o s e l e c t the m a i n
menu. Asyou scrollthrough the menu,theselection willbe highlighted in blue.
3. P r e ss the R I G HT nav i gate ke y t o enter the highlighted sub menu . U s e the UP/DOWN nav i gate ke ys t o
select withinthe sub menu. UsetheLEFT/RIGHT navigate keystoenableordisable
parameters.
4. To returntothe previous menu, you need topressreturninthe sub menu orMENU onthe remote.
To fully leave the menu,press theMENU keyagain.
5. OSD M en u S ett i ng L i s t :
PTZF
FOCUS MODE
AUTO/MANUAL: Ability to change from auto or manual focus
DEFAULT: AUTO
DIGITAL ZOOM
ON/OFF: Ability to digitally zoom 2X. (PTZ-X12-IP | PTZ-NDI-X12 only)
DEFAULT: OFF
RATIO DISPLAY
ON/OFF: Grants display of the zoom X module. Off by default.
DEFAULT: OFF
ZOOM SPEED
Zoom speed control IR remote: 7 changeable levels.
DEFAULT: 5
SPEED BY ZOOM
When zoomed into the max, the camera will slowly tilt
DEFAULT: ON
PAN/TILT SPEED
Pan/Tilt speed control by IR remote. Controllable at different levels
DEFAULT: 18
RETURN
Return to previous menu.
EXPOSURE MODE
AUTO/MANUAL/BRIGHT/SHUTTER/IRIS: Choose the current Exp. Mode
DEFAULT: AUTO
EXPOSURE
SHUTTER
Set shutter speed. 1/30-1/10000: Allows for tuning of the shutter speed
DEFAULT: AUTO
IRIS
Set Iris: CLOSE-F1.8: Allows for tuning of the Iris opening.
DEFAULT: AUTO
GAIN
Set gain: 0dB-28dB: Allows for tuning the gain of the camera
DEFAULT: AUTO
BRIGHTNESS
Set brightness: 0-15: Allows for tuning the brightness of the camera
DEFAULT: AUTO
FLICK
Allows for adjustment of the flickerless options on the camera
DEFAULT: 50Hz
BLACKLIGHT
Allows for the enabling of the blacklight or not.
DEFAULT: OFF
GAMMA
Allows setting changes for the Gamma option of the camera
DEFAULT: 0
RETURN
Return to previous menu
IMAGE
WB MODE
AUTO/INDOOR/OUTDOOR/PUSH/ATW/MANUAL/SODIUM
DEFAULT: ATW
BLUE
Set red gain level: 0-255 (Allows for precise tuning of the blue setting)
DEFAULT: AUTO
RED
Set blue gain level: 0-255 (Allows for precise tuning of the red setting)
DEFAULT: AUTO
DEFOG
Set defog level: This setting allows you to clear up the hazy images
DEFAULT: 0
MIRROR
ON/OFF: Makes the image flip on the vertical plane
DEFAULT: OFF
FLIP
ON/OFF: (optional) Makes the image flip on the horizontal plane
DEFAULT: OFF
COLOR/B&W
COLOR/B&W: Allows for B&W color mode
DEFAULT:
COLOR
GAIN LIMIT
Allows you to cap the gain at a certain level
DEFAULT: 15
RETURN
Return to previous menu