Aimsak ALC 3540 User manual

IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
DANGER - TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE INSTRUCTIONS
▣MODEL
Charger ALC 3540
▣ SAFETY INSTRUCTIONS
WARNING! Read all safety warnings and all instructions.
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious personal injury.
Save all warnings and instructions for future reference.
1. ELECTRICAL SAFETY
- Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or ground surface, such as pipes, radiators,
ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or
grounded.
“The appliance is not to be used by persons(including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been give Supervision or instruction.”
“Children being supervised not to play with the appliance.”
“If the cord is damaged, it must be replaced by
an authorized Aimsak Service Centre or similarly qualified person in order
to avoid a hazard.”
▣REATED VOLTAGE
INPUT : 220 - 240V ~ / 50 - 60Hz / 200 W
OUTPUT : 10.8V - 18V 4A

- Do not expose power tools to rain or wet conditions.
Water entering a power tool will increse the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or
unpluging the power tool.
Keep cord away from heatm oil, sharp edges or moving parts.
Damaged or entangled cords increse the risk of electric shock.
- When operating power tools in outdoor, use an extension cord suitable
for outdoor use.
Use of a cord suitable for outdoor reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
2. Li-ion BATTERY CHARGER INSTRUCTIONS
WARNING! USE THE CORRENT VOLTAGE OF CHARGER.
- Do not charge other manufacturer batteries only except Aimsak’s one.
The appliance is only suitable for charging Aimsak batteries.
Due to risk of fire and explosion.
- Ensure that the plug and power code is abnormalities.
Do not use damaged charger. Due to electric shock.
- Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
- Keep the battery charger in a dry and frost-free place.
Enter water in the battery charger create failure and electric shock.
- Do not carry the battery charger with power code and not to plug out with
the wire.
Protect from heat, water and sharp edge. Due to risk of short-circuit.
- Plug out immediately if battery charger is damaged or heated, due to fire
and explosion when charging continously.
- Ensure that charger terminal is clean. Pollution causes electric shock.
- Do not charge and operate the battery charger on combustible ground or
surroundings due to its
heating during the charging process. Heated battery charger currents to fire.

Meaning
Indicators
Standby
Charging
Finish
High Temp
Low
Voltage
Red & Green
LED On
Green LED
Frickering
Battery charging is Workable.
Battery is Being Charged.
Fully charged.
Battery temperature has missed the normal range.
(0~45 )
Charge will automatically start when allowable
temperature is reached.
Pre-charging mode voltage of the battery is low.
(When a constant voltage charging mode
is switched to rise.)
Red LED On
Green LED On
Indicators and Meaning
OR
How to Recharge
- Put the adapter into charger. Then, insert 18V Li-ion Battery onto the adapter and
start to chage it.
<Note> Without the adapter, you can use this charger to recharge other 10.8V or
14.4V Plug-in type of batteries.