Aircat 1056-XL User manual

MODEL: 1056-XL / 1076-XL
1/2” & 3/8” IMPACT WRENCH

SPECIFICATIONS
Important Warnings - Impacts
1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact
driver.
2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring
and pin should be used to prevent the socket falling off and causing injury.
3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool
damage and replace when necessary.
Accessory Hazards
4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT (US) or BSP (UK). Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply
Model No. Free Speed
(RPM)
Bolt Capacity
(in.)
Square
Drive
(in.)
Impacts Per
Minute
Max. Torque
(ft-lb) @90 psi
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
1076-XL 9,000 9/16 3/8 1650 550 2.5 4.25 8 3/8 1/4
9,000 9/16 1650 550 2.5 4.25 8 3/8 1/4
1056-XL 1/2

MODEL: 1056-XL / 1076-XL
1/2” & 3/8” IMPACT WRENCH
Exploded View & Parts List
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
1 9638001M AIR INLET (USA) 1 27 9638013 O-RING 1
9638001M-BSP AIR INLET (UK) 1 28 9651235 VALVE BODY 1
2 9638003 O-RING 1 29 9OR8501 O-RING 1
3 9ORAS-115 O-RING 1 30 9611238 REVERSE VALVE LEVER 1
4 9638005 DEFLECTOR 1 31 9651237 REVERSE VALVE 1
5 9638006 SPRING 1 32 9OR1301 O-RING 1
6 9328804C VALVE STEM 1 33 9611239-1 SPRING 2
7 9328835 VALVE SEAT 1 34 9SB0003-1 STEEL BALL 2
8 9328825S WASHER 1 35 9611240 POWER MANAGEMENT KNOB 1
9 9638010 RETAINING RING 1 36 9611236 RETAINER 1
10 9651210-1056 HOUSING FOR 1056-XL 1 37 9S8512 SPRING 1
9651210-1076 HOUSING FOR 1076-XL 1 38 9261206-BK TRIGGER 1
11 9638011 SPRING PIN 1 39 9589039 SPRING PIN 1
12 9611212 SCREW 1 40 9651207-RD GASKET 1
13 9651213 BOLT 4 41 9251225 HAMMER 1
14 9WW-18 WASHER 1 42 9251212 HAMMER FRAME 1
15 9R6 BALL BEARING 1 43 9251213 HAMMER PIN 2
16 9651206 REAR PLATE 1 44 9251208 1/2" ANVIL FOR 1056-XL 1
17 9251205 ROTOR 1 9251208-1 3/8" ANVIL FOR 1076-XL 1
18 9251203 ROTOR BLADE 6 45 9OR7718 RETAINER O-RING FOR 1056-XL 1
19 9251218 CYLINDER 1 9328829-3 RETAINER O-RING FOR 1076-XL 1
20 9SP0308 SPRING PIN 2 46 9328830-4 SOCKET RETAINER FOR 1056-XL 1
21 9OR1315 O-RING 1 9328830-3 SOCKET RETAINER FOR 1076-XL 1
22 9651202 FRONT PLATE 1 47 9251216 ANVIL BUSHING 1
23 9EE4 BALL BEARING 1 48 9651230-NICAT HAMMER CASE 1
24 9SP2520 SPRING PIN 1 49 9638047 GREASE FITTING 1
25 9651234 VALVE BUSHING 1 50 9651245 MUFFLER TUBE 1
26 9651232 TRIGGER PIN 1 51 9389507-1056 SILENCER 1

SERVICE CENTER LISTINGS ENCLOSED
AIRCAT and NITROCAT air tools are warranted to be free from defects in material and workmanship for 2 years from date
of purchase. We will repair or replace; at our option any defective part or unit which proves to be defective in material or
workmanship during this 2 year period. The foregoing obligation is AIRCAT and Florida Pneumatic's sole liability under this
or any implied warranty, under no circumstances shall it be liable for any incidental or consequential damages.
This warranty applies to the tool only. The warranty does not apply to any attached accessories/consumable products;
such as drill chucks, sander backing pads, air hammer retainers and chisels or “kit” accessories or any other accessory
included with the tool.
an AIRCAT or Florida Pneumatic Authorized Service Center) are not covered by this warranty.
Return your tool to an AIRCAT or Florida Pneumatic Authorized Service Center freight prepaid. Be sure to include your
name, address, copy of purchase with date and description of the suspected defect.
AIRCAT whose policy is continued product improvement reserves the right to make changes in design or construction at
any time without incurring any obligation on tools previously sold.
[email protected]
USA AIRCAT Europe
A Division of Universal Air Tool Company Limited
Unit 8 Lane End Industrial Park, High Wycombe HP14 3BY
Ph: 01494 883300 / Fax: [phone]
[e-mail] www.universal.co.uk