Aircat 1350-XL Datasheet

MODEL: 1350-XL
HIGH-LOW TORQUE 3/8" IMPACT WRENCH

SPECIFICATIONS
Important Warnings - Impacts
1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact
driver.
2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring
and pin should be used to prevent the socket falling off and causing injury.
3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool
damage and replace when necessary.
Accessory Hazards
4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
Model No. Free Speed
(RPM)
Bolt
Capacity
(in.)
Square
Drive
(in.)
Impacts
Per Minute
Max. Torque
(ft-lb)
High-Low
Torque
Setting (ft-lb)
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air
Inlet
(in.)
1350-XL 10,000 1/2 3/8 1700 500
(Reverse Torque) 500 & 100 3.15 6.3 6 3/8 1/4 NPT
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply

MODEL: 1350-XL
HIGH-LOW TORQUE 3/8" IMPACT WRENCH
Exploded View & Parts List
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
1 9638001M AIR INLET 1 24 9612834 HAMMER FRAME 1
2 9OR2002 O-RING 1 25 9612835 HAMMER 2
3 9ORAS-115 O-RING 1 26 9612837-38 3/8" ANVIL 1
4 9612805 DEFLECTOR 1 27 9328829-3 O-RING 1
5 9638006 SPRING 1 28 9328830-3 SOCKET RETAINER 1
6 9328804C VALVE STEM 1 29 9612840P BUSHING 1
7 9328835 VALVE SEAT 1 30 96238T30-TI HAMMER CASE 1
8 9328835S WASHER 1 31 9621224 REVERSE VALVE 1
9 9638010 RETAINER RING 1 32 9OR1802 O-RING 1
10 96238T10-CAT MOTOR HOUSING W/
BUSHING
1 33 9OR17418 O-RING 1
11 9SP0328 SPRING PIN 1 34F 9623829F-BK FORWARD BUTTON 1
12 96238T14-BK TRIGGER 1 34R 9623829R-BK REVERSE BUTTON 1
12-1 9621214P TRIGGER PIN 1 35 9328814 DETENT PIN 2
13 9611213 BOLT 4 36 9621238 SPRING 2
14 9611214 SCREW 3 37 9623828 SPACER 1
15 9OR2512 O-RING 1 38 9633809-1 SCREW 1
16 9BR6ZZ BALL BEARING 1 39 96212T39-RD1 REGULATOR SWITCH 1
17 96238T17 END PLATE 1 40 9SS0212 SPRING 1
18 9612830-1 ROTOR 1 41 9589040 SPRING PIN 1
19 9612831C BLADE 6 42 9SB0003-1 STEEL BALL 1
20 9623820 CYLINDER 1 43 9638047 GREASE FITTING 1
21 9623821-BK GASKET 1 44 9612812 SILENCER 1
22 9B6001ZZ BALL BEARING 1 45 9SB0003 STEEL BALL 2
23 9612836 HAMMER PIN 2 46 9612802 PIN 1
47 9612846 SCREW 1

SERVICE CENTER LISTINGS ENCLOSED
AIRCAT and NITROCAT air tools are warranted to be free from defects in material and workmanship for 2 years from date
of purchase. We will repair or replace; at our option any defective part or unit which proves to be defective in material or
workmanship during this 2 year period. The foregoing obligation is AIRCAT and Florida Pneumatic's sole liability under this
or any implied warranty, under no circumstances shall it be liable for any incidental or consequential damages.
This warranty applies to the tool only. The warranty does not apply to any attached accessories/consumable products;
such as drill chucks, sander backing pads, air hammer retainers and chisels or “kit” accessories or any other accessory
included with the tool.
an AIRCAT or Florida Pneumatic Authorized Service Center) are not covered by this warranty.
Return your tool to an AIRCAT or Florida Pneumatic Authorized Service Center freight prepaid. Be sure to include your
name, address, copy of purchase with date and description of the suspected defect.
AIRCAT whose policy is continued product improvement reserves the right to make changes in design or construction at
any time without incurring any obligation on tools previously sold.
Tune-Up and Head Kits for all AIRCAT PNEUMATIC impact wrenches and ratchets are available.
For Authorized Service Centers, please visit www.aircat.com/warranty-service