aireRyder Toledo FN11146 User manual

1
INSTRUCTIONS FOR INSTALLATION AND USE
Ceiling Fan Model Toledo (FN11146 / FN11156)
BEFORE YOU START
Proper use:
-This product is intended exclusively for non-commercial use as ceiling fan.
-The product has to be installed and used in accordance with these instructions.
-Any use of this product that is not in accordance with these instructions will void the legal
warranty of the manufacturer.
Please keep the original carton and packaging material as the warranty will only be honored if product
is returned in complete original packaging.
FOR YOUR OWN SAFETY
General safety instructions:
-For the safe use of this product, you need to have read and understood these instructions
before installing or using the product.
-Please follow all safety instructions! If you ignore these safety instructions, you will endanger
yourself and others.
-Keep these instructions for future reference.
-All parts of this product have to be installed properly in order to ensure safe operation.
-Modification of the product and use of non-approved parts are prohibited.
-This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the product by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the product.
Electrical safety:
-The electrical installation must be performed by a qualified electrician and must be in
accordance with national and local regulations.
-Use a fault-current circuit breaker with a rated residual current of no more than 30 mA.
-Make sure to install an all-pole disconnection switch having a contact separation of at least
3mm between poles in the supply wiring to the ceiling fan.
-Before connecting the appliance to the electrical grid, make sure that it will only be operated
within the specified parameters.
-The fan must be properly grounded to avoid the risk of electric shocks.
-Switch off the power before connecting, repairing or cleaning the fan.
Storage and transport:
-Always store the fan in a dry environment.
-Protect the fan from damages during transport.

2
Safety instructions specific to this fan:
-Attach the fan only directly to the ceiling structure.
-The carrying capacity of the ceiling structure from which the fan is hung must be at least three
times the weight of the fan.
-The minimum distance between the blades of the fan and the floor must be 2.3m.
-Never mount the fan outside or in a humid or wet environment. The fan can not be installed
within proximity of water (e.g. bath tub, swimming pool, water connection).
-The fan can only be installed horizontally on the ceiling.
-Switch off the power before connecting, repairing or cleaning the fan.
-The rotor area has to be kept clear of any objects at all times.
-Be careful when working near the rotating blades.
FAN OVERVIEW
1. Canopy
2. Motor housing
3. Propeller
UNPACK THE FAN
-Unpack the fan and check that contents are complete.
-Dispose of packaging – see also “Disposal”.
Contents of packaging:
Instructions for Installation and Use 1PC Mounting screw 2PCS
Mounting bracket 1PC Spring washer 2PCS
Fan assembly 1PC Flat washer 2PCS
Fan blade assembly 1PC Lock washer 2PCS
Propeller nut 1PC Blade balance kit 1PC
Wall control 1PC Wood screw 2PCS
Note: In case of damaged or missing parts, please contact your retailer.
INSTALLATION
Risk of electric shock: Switch off the electricity using the switch at the circuit breaker box before
installing the fan.
Risk of electric shock: The electrical installation must be performed by a qualified electrician and
must be in accordance with national and local regulations.
Risk of injury: In case you need to drill holes for mounting the fan, make sure that the drills have
sufficient distance to in-ceiling wiring.

3
Installation Instructions:
1. Turn off power at breaker
box to avoid possible
electrical shock.
2. Pass the supply wires through the
mounting bracket. Secure the mounting
bracket to a ceiling joist or other structural
ceiling element with two screws, spring
washers and flat washers.
Note: The structural element must support
at least three times the weight of the fan.
3. Lift fan assembly onto
mounting bracket.
4.
Rotate fan so that the groove on the ball
engages the ridge in the mounting
bracket. Connect ground (green) wires
as shown.
Note: Do not rotate the fan assembly
more than 360 degrees.
5. Make wire connections
Mounting
Bracket
Mounting
Bracket
Screw
Fan
Assembly
Ridge
Ball Groove
Mounting Bracket
Ground Wire
From Ceiling
Mounting Screw
Wall Control
Wall Outlet Box
TO FAN
TO HOT
Wall Plate
Green Blue Brown
See Figure 2
(see next page) See Figure 1
(see next page)

4
Line out to fan
a.
a
t wall
(Fig.1):
1. Connect supply in from house to wall control
node marked “TO HOT”.
2. Connect line out to fan to wall control node
marked “FAN”.
Note: The “TO LIGHT” node on wall control is
not applicable for this fan.
b. at ceiling (Fig.2):
1. Connect blue wire from fan to terminal block
marked “N”.
2. Connect brown wire from fan to terminal block marked “L”.
3. Connect green wire from ceiling to terminal block marked “ ”.
4. Connect blue wire from ceiling to terminal block marked “N”.
5. Connect line in from wall control to terminal block marked “L”.
AFTER ALL WIRES ARE CONNECTED:
(1) Attach wall control unit to outlet box using the two mounting screws provided.
(2) Attach wall plate to the switch control front.
Note: Wires from house may vary in color and may not include ground wire (green/yellow).
WARNING
To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box
and not pinched between the wall plate and the wall.
WARNING
Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate fan until the blades are in place. Noise and fan
damage could result.
6
. Canopy installation
a. Push up the canopy until the two screws on mounting
bracket are engaged with key holes in canopy.
b. Rotate the canopy slightly until the two screw heads
are in the small end of the key holes.
c. Tighten both screws.
Wall Control
Supply in from house
Brown
(AC
-
L
)
From Fan From Ceiling
Green
Blue
Brown
Brown
Blue
Yellow Green
Canopy
Screw
Key Holes

5
7. Set up fan configuration a. Remove the set screw between yokes and adjust motor to
preferable position
b. Possible fan configurations are shown below. Line up the
motor yoke and pipe yoke for the desired configuration, as
shown below.
c. Replace the set screw and tighten.
For 45 degree
For 90 degree
For 0 degree
Motor Yoke
Set Screw
Pipe Yoke
Motor Yoke
Pipe Yoke
Set Screw
Motor Yoke
Pipe Yoke
Set Screw
Pipe Yoke
Set Screw
Motor Yoke

6
8. Blade Installation
a. Attach Propeller to spindle. b. Thread the propeller nut counter-clockwise
on spindle until fully tightened.
CLEANING
Risk of injury: Before cleaning the fan, always switch off the power at the main circuit breaker and
wait until the fan has come to a complete stop.
Clean the fan with a dry or damp soft cloth. Do not use any liquids or detergents.
DISPOSAL
Disposal of the fan: You are required to dispose of electric and electronic appliances separately from
your household waste. Please inquire at your municipality regarding proper ways of disposal.
By separately disposing of your electric and electronic appliances, you are participating in recycling and
you are helping to prevent potentially toxic substances from polluting the environment.
Disposal of the packaging: The packaging consists of cardboard and marked plastic and Styrofoam
which can be recycled. Please recycle.
MALFUNCTIONS – TROUBLE SHOOTING
Risk of injury: Inappropriate repairs can lead to the fan not functioning safely. This can cause a
hazard for yourself and your environment.
Please check the following table before contacting your retailer.
Malf
unction
Underlying cause (error)
Solution
Fan does not turn. Fan switched off? Switch on fan.
No mains voltage? Check circuit breaker.
Wiring connected incorrectly? Check step 5 to ensure wiring
connected correctly.
Fan vibrates. Fan not installed properly? Install fan thoroughly according
to installation instructions.
If you can not resolve the malfunction yourself, please ask your retailer directly.
Please note that the warranty will be voided by inappropriate repairs.
TECHNICAL DATA(When used with wall control)
Speed
Voltage
Power
RPM
IV
230V ~ / 50Hz
38.7W 659
III 30.7W 569
II 19W 435
I 15.4W 369
MANUFACTURER
Vaxcel International Co., Ltd.
121 E North Avenue, Carol Stream, IL, USA
www.vaxcel.com
Spindle Propeller Nut
Propeller Nut
Propeller