aireRyder Cyrus User manual

1
INSTRUCTIONS FOR INSTALLATION AND USE
Ceiling Fan Model Cyrus (FN44444)
BEFORE YOU START
Proper use:
-This product is intended exclusively for non-commercial use as ceiling fan.
-The product has to be installed and used in accordance with these instructions.
-Any use of this product that is not in accordance with these instructions will void the legal
warranty of the manufacturer.
Please keep the original carton and packaging material as the warranty will only be honored if product
is returned in complete original packaging.
FOR YOUR OWN SAFETY
General safety instructions:
-For the safe use of this product, you need to have read and understood these instructions
before installing or using the product.
-Please follow all safety instructions! If you ignore these safety instructions, you will endanger
yourself and others.
-Keep these instructions for future reference.
-All parts of this product have to be installed properly in order to ensure safe operation.
-Modification of the product and use of non-approved parts are prohibited.
-This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the product by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the product.
Electrical safety:
-The electrical installation must be performed by a qualified electrician and must be in
accordance with national and local regulations.
-Use a fault-current circuit breaker with a rated residual current of no more than 30 mA.
-Make sure to install an all-pole disconnection switch having a contact separation of at least
3mm between poles in the supply wiring to the ceiling fan.
-Before connecting the appliance to the electrical grid, make sure that it will only be operated
within the specified parameters.
-The fan must be properly grounded to avoid the risk of electric shocks.
-Switch off the power before connecting, repairing or cleaning the fan.
-Install only bulbs of the type intended for your fan.
Storage and transport:
-Always store the fan in a dry environment.
-Protect the fan from damages during transport.
F A N C O
161031

2
Safety instructions specific tothis fan:
-Attach the fan only directly toceiling structure.
-The carrying capacity of the ceiling structure from which the fan is hung must be at least three
times the weight of the fan.
-The minimum distance between the blades of the fan and the floor must be 2.3m.
-Never mount the fan outside or in a humid or wet enviroment. The fan can not be installed
within proximity of water (e.g bath tub, swimming pool, water connection).
- The fan can be installed with downrod mount or slope ceiling mount (up to 23 degrees).
-Switch off the power before connecting, replairing or cleaning the fan.
-The rotor area has to be kept clear of any objects at all times.
-Be careful when working near the rotating blades.
FAN OVERVIEW
UNPACK THE FAN
INSTALLATION
Contents of packaging:
Instructions for installation and use
Canopy
Hanger Bracket
Downrod Set (Includes Ball Joint, 4”
Downrod, Hanger Pin & Lock Pin)
Risk of electric shock:
1. Canopy
2. Downrod
3. Motor Housing
4. Fan Blade
5. Fan Switch Box
6. Fan Light
Note: Incase of damage or missing parts, please contact your retailer.
Switch off the electricity using the switch at the circuit breaker box before
installing the fan.
Risk of electric shock:
The electrical installation must be performed by a qualfied electrcian and must
be in accordance with national and local regulations.
Risk ofinjury:
In case you need to drill holes for mounting the fan, make sure that the drills have
sufficient distance to in-ceiling wiring.
-Unpack the fan and check that contents of packaging are complete.
-Dispose of packaging – see also “Disposal”.
F A N C O
161031
1
2
34
5
6
Downrod Stand Cover
Blade Brackets (3 PCS)
Fan Blades (3 PCS)
Motor Housing
Switch Box Cover
Fan Light
Assembly Kit
Suction Cup
Pull Chains

Fig.1
Turn off the electric circuit at the
main fuse or circuit breaker box.
Thread the motor wires through the
downrod stand cover, canopy and
downrod.Then restore support pin
and downball back by tightening
screw.
Hanger Pin
Lock Pin
Screw
Support Pin
Ball Joint
Hang the fan on hanger bracket,
and make sure the slot of ball joint
is fitted into the guide pin of hanger
bracket.
Remove the lock pin and take off
the hanger pin.Then remove screw
and slide the ball joint down to take
off support pin.
Fig.3
Insert and tighten the two collar
screws. Slide lock pin into hanger
pin.
Fig.6
Lock Pin
Collar Screws Slot
Guide Pin
Hanger Bracket
Fig.7
Loosen the collar screws partly.
Insert the downrod into the collar.
Slide hanger pin through holes of
collar and downrod and secure with
lock pin.
Hanger Pin
Motor Wires
Downrod
Downrod Stand
Cover
Collar
Canopy
Fig.5
Motor Wires
Downrod
Downrod Stand
Cover
Canopy
Fig.4
Attach the hanger bracket to the ceiling
with spring washers, flat washers and 2
mounting screws.
Note: For sloped ceiling installation, make
sure that the hanger bracket is installed
so that the guide pin is facing upward.
Hanger
Bracket
Fig.2
Guide Pin
Flat Washer
Spring Washer
From House Wire
Terminal Block
House Wire
(AC-L)
L(AC-N)
N
Female Connector
Female Terminal
Male Connector
Male Terminal
Fig.8 1. Make house wire connections. Follow diagram on
the left and make sure that all exposed wires are
tightened by screw on terminal block.
Note:
a.) The terminal block shown in left graph is
pre-installed on the mounting bracket.
b.) After wiring is completed, gently push wires into
hanger bracket with terminal block facing upward (if
applicable).
2. Make fixture wire connection. Plug the male
connector into female connector and plug the male
terminal into female terminal.(Do not force
it into wrong receptacle as it will cause damage.)
N
L
Fixture Wire
3
F A N C O
161031

F A N C O
161031
4
Remove the motor screws and washers
from the motor assembly. Secure blade
brackets to the motor with washers and
motor screws.
Attach the canopy to the hanger
bracket, then secure it with four
screws and washers.
Thread the blade screws through the
rubber washer blade bracket and blade
into the decorative cap. Tighten all blade
screws securely. Repeat on other blades.
Fig.10
Blade
Blade Bracket
Blade Screw
Fig.11
Motor Screw
Washer
Blade Bracket
Screw
Hanger Bracket
Washer
Canopy
Fig. 9
Decorative Cap
Rubber Washer
Fig.12
Switch Box
Screw
Switch Box Cover
Install without fan light
Make sure the wires of the fan light in
the switch box are capped.
Secure the switch box cover with
the switch box screws.
To install the fan light, skip this step
and proceed to Fig.13.
Fan Light Installation:
Fig.14
Switch Box
Screw
Secure the fan light onto the switch
box by using the switch box screws.
Switch Box
Fan Light
Female Terminal
Male Terminal
Fig.13
Make wire connection:
-- Connect the blue wire from the switch box to
blue wire from the fan light by inserting male
terminal into female terminal.
-- Connect the red wire from the switch box to
red wire from the fan light by inserting male
terminal into female terminal.
Carefully put the wires into the switch box.

F A N C O
161031
5
Fig.17
Turn on the electric circuit at the main fuse
or circuit breaker box.
The slide switch on the switch box sets the direction of fan rotation.
Select the desired direction of fan rotation. Push the slide switch
down for " Forward" and up for "Reverse".
Note: Wait for fan to stop before reversing the direction of blade
rotation.
Fig.16-b
Reverse
Forward
Fan Speed Pull
Chain
Fan Light Pull
Chain
Install pull
chains and
drops
Reverse
Forward
Fig.16-a
Slide Switch Switch Box
Slide Switch
Install bulbs (Excluded).
a. Attach the suction cup to the surface of the halogen bulb lens.
b. Insert and twist the bulb (GU10 MR16C BULB ONLY) into the socket by
using the suction cup.
c. Remove the cup from the halogen bulb lens by pulling the knob of the suction
cup.
d. Repeat with other bulbs.
Do not discard the suction cup, it will be needed when replacing the bulb.
Adjust the spotlight head to a desired position by using the swivel.
Caution: Turn off the electric circuit and allow the fixture to cool down
completely before replacing the bulbs.
Bulb GU10 Max.50W
(Excluded)
Suction Cup
Fig.15
Install two pull chains and drops onto the pull chains located in the switch box and light kit.
The pull chain controls the fan speed as follows:
1 pull – High, 2 pulls – Medium, 3 pulls – Low, and 4 pulls – Off.
To turn the light kit “ON” or “OFF”, pull the chain that is attached to the light kit.
Caution: If you install a remote control or a wall control for this fan, pull the pull chains to “high speed” of the
fan motor and “on” of the fan light.

F A N C O
161031
6
MALFUNCTIONS - TROUBLE SHOOTING
Risk of injury: Inappropriate repairs can lead to the fan not functioning safely. This can cause a hazard for yourself
and your environment.
Most malfunctions are caused by small errors which you can easily resolve by yourself. Please check the following table
before contacting your retailer. This way, you can spare yourself a lot of effort and cost.
If you can not resolve the malfuntion yourself, please ask your retailer directly. Please note that the warranty will be
voided by inappropriate repairs.
Vaxcel International Co., Ltd.
121 E North Avenue, Carol Stream, IL, USA
www.vaxcel.com
MANUFACTURER
Disposal of the fan: You are required to dispose of electric and electronic appliances separately from your household
waste.Please inquire at your municipality regarding proper ways of disposal.
Be separately disposing of your electric and electronic appliances, ou are participating in recycling and you are helping
to prevent potentially toxic substances from polluting the environment.
Disposal of the packaging: The packaging consists of cardboard and marked plastic and Styrofoam which can be
recycled. Please recycle.
DISPOSAL
Risk of injury: Before cleaning the fan, always switch off the power at the main circuit breaker and wait until the
fan has come to a complete stop.
Clean the fan with a dry or damp soft cloth. Do not use any liquids or detergents.
CLEANING
Malfunction
Fan does not turn.
Fan vibrates.
Light does not work.
Fan or fan light can not
be controlled using the
remote control.
Switch for fan speed or fan light not
in correct position?
Switch the fan speed to high
and the fan light to on.
Lamp defective? Exchange lamp.
Fan switched off. Switch on.
Check circuit breaker.
Install new batteries.
Install fan thoroughly
according to installation
instructions.
No mains voltage?
Batteries of remote control empty?
Fan not installed properly?
Underlying cause (error) Solution