AirMobi iTravel3 User manual

Quick Installation Guide
Wireless Travel Router
iTravel3
V1.0

1
Package contents
iTravel3 x 1 Mirco USB Cable x 1
Quick Installation Guide x 1
Note: If any of items is missing or damaged, please contact your retailer.
Hardware

2
No.
Item
Description
1
Mode Switch
3G/Repeater/Router
2
USB
Used for charging the device
3
Reset
Long press the button for at least 5 seconds,
and then the router will restore to the default
setting
4
USB 1.0A
Used for charging the smart phone
5
USB 2.1A
Used for charging the smart phone or tablet
6
Power Button
Long press the button for Startup & Shutdown
Press the button to show the battery level
7
Status LED
Solid Blue:The device is operating properly
Solid Red:The device is starting up or restoring
the factory configuration
Off :System is abnormal or power is off
8
Battery Level LED
4 LEDs display different battery levels. Marquee
display the device in charging status, the LEDs is
normally on when the battery is fully charged.
9
LAN/WAN
Use as either a LAN port or WAN port
10
SIM card slot
Plug a 3G SIM card to share the 3G Internet

3
Working Mode
3G Mode
In 3G Mode, it enables multiple Wi-Fi devices to share Internet via 3G
networks. In this mode, the Ethernet port works as a LAN port.
Recommend for: outdoor environment, mobile office, etc.
Repeater Mode (Wireless Repeater)
In Repeater mode, iTravel3 extends the coverage of your existing wireless
router.
Recommend for: villa, big house, etc.

4
Router Mode (Wireless Router)
In Router mode, iTravel3 work as a wireless router.
Recommend for: home, apartment, hotel,etc.
Network Configuration
Make sure the 3G/Repeater/Router mode switch on the iTravel3 is set to
what you need.
3G Mode Setup
1. Power on the iTravel3 and wait for Status LED turn from red to blue, and
then insert your 3G SIM card into the USB port of the iTravel3.
2. On your computer/ Smart phone /tablet, find and connect to iTravel3’s
WiFi network to access Internet. The default wireless network name is
AirMobi_XXXXXX , not encrypted by default.

5
3. If you want to setup the password of iTravel3’s WiFi, please open a web
browser and enter “c.cctairmobi.com” or ”192.168.8.8”in the address bar
and login.
No Username and Password by default. If you want to set them, please
click ”System tools->User Settings”when you login.
After you login, click “Wireless Settings->Wireless Security Settings”to set
the WiFi password.
You need to connect to iTravel3 again when you finish the settings.

6
Repeater Mode Setup
1. Check the device connection that follows the diagram in Working Mode.
Power on the iTravel3 and wait for Status LED turn from red to blue.
2. On your computer/ Smart phone /tablet, find and connect to iTravel3’s
WiFi network. The default wireless network name is AirMobi_XXXXXX, not
encrypted by default.
3. Open a web browser and enter “c.cctairmobi.com” or ”192.168.8.8”in
the address bar and login.
4. Log in to setup wizard page, follow Setup Wizard to complete setup.

7
5. Click Next button to configure Internet connection in Repeater mode.
Click Search button to select a wireless network to extend, and type the
network password.
When the connection is completed, the default setting is Synchronism SSID.
The iTravel3 will use the same wireless network name (SSID) and password as
your existing wireless router.
If “Synchronism SSID”is not checked, click the Next button to configure your
WiFi security, enter the name and password for the extender wireless
network.

8
6. Click the Next button, complete the network configuration in Repeater
mode. Connect your computer/Smart phone/tablet to the new created
network.
Router Mode Setup
1. Follow the step 1, 2, 3 in Repeater Mode Setup.
2. Log in to setup wizard page, follow Setup Wizard to complete setup.
3. Click Next button to configure Internet connection in Router mode.
In Router mode, there are three Internet connections available: Static IP,
DHCP, and PPPoE. iTravel3 will choose the right connection automatically and
you only need to fill in the corresponding parameters. The configuration data can
be get from your ISP.
PPPoE: Used for ADSL services, type in the Username and Password provided by
your ISP.

9
DHCP: Nothing provided by Your ISP, no configuration is needed.
Static IP: Type in the Static IP Address, Subnet Mask, Default Gateway and
DNS Server Address provided by your ISP.
4. Click the Next button into configure your WiFi security, enter the WiFi
name and password for iTravel3’s wireless network.
5. Click the Next button, complete the network configuration in Router
mode. Connect your computer/Smart phone/tablet to the new created
wireless network.

10
Power Bank
iTravel3 as a power bank, built in 10400mAh lithium battery, can charge the
mobile devices such as smart phones, tablet, etc. You can press the Battery
Level LED to check the remaining capacity of battery.
Output 1.0A is only for smart phone,and Output 2.1A is for smart
phone or tablet.

1
Technical Support
For more information or troubleshooting help, please download the User Manual
from our website: www.cctairmobi.com
Additional support is also available on our website.It contains the latest user
documentations and software updates for AirMobi products.
Support E-mail Address: [e-mail]
Copyright© 2013 Shenzhen Huaxunark Technology Co., Ltd. All rights reserved.