Airpho AR-E200 User manual

LED Explanations
Status
On
Blinking
Off
Color Indication
Green
Red
Red
The Extender is connected to the
router, and is in good location.
There is no active connection.
WPS connection is in progress.
The Extender is off.
Wait about 1 minute
until the LED is lit in
solid red.
– –
Quick Setup Using the WPS Button
METHOD ONE
Power on the Extender
Plug the Extender into an electrical outlet next to your router.
1
Relocate the extender
1.Plug in the Extender into an electrical outlet halfway
between your router and the Wi-Fi dead zone. You
need to make sure the location you choose is within
the range of your host network.
2.Wait about 1 minute until the LED is lit and solid
green. If not, relocate it closer to the router to achieve
better signal quality.
Host Network
AR-E200
Extended Network
WPS
3
1. Press the WPS button on your router.
2.Press the WPS button on your Extender within 1 minute.
Connect to the Extender’s network
2
The LED should turn from
blinking red to solid green,
indicating a successful WPS
connection. If not, please try
METHOD TWO.
Airpho Technology Co.,Ltd
Web: www.airpho.com
Quick
Installation Guide
300Mbps Wi-Fi Range Extender
AR-E200

METHOD TWO
Power on the Extender
Plug the Extender into an electrical outlet next to your
router.
Wait until the LED
change to solid red.
1
2
Configure the Range Extender
www.airphoextender.net
1.Launch a web browser and enter www.airphoexten
der.net in the address field. You will be guided to the
Extender Setup Page.
2.Select your router’s 2.4GHz network to extend and
enter its wireless password ,then click Confirm.
Exten de r|AR- E2 00
Selec t a ho st netw or k
Adv anced S ettin gs>>>
AR-W2 00
00:05 :1 d:03: 04 :05
Host_ Ne twork
4c:6e :6 e:00: 39 :b6
2c:b2 :1 a:ca: be :cd
AR-W4 00
AR-W4 10
4e:6e :6 e:5c: 10 :b0
3
5. Check the LED status on your extender. The LED
should turn solid green, indicating a successful
connection; if not, please refer to FAQs on Airpho official
website: www.airpho.com
Exte nd er|AR-E200
Connecting 80%
Extender SSID: Host_Network_ext
Cancel
3. Set the network name (SSID) and password for your
extender. You may either keep the default SSID, or
customize it for the extended 2.4GHz network, then
click .Confirm
4. Verify your wireless settings and click . It will take Confirm
about 15 seconds to proceed.
Setup your extender SSID
Host_Network_ext
We recommend setting your extender SSID
same as your router to create seamless home
networking
Cancel Confirm
Ext ende r|AR -E20 0
Sele ct a host network
Advance d Se ttings> >>
INTELBR AS
00: 05: 1d: 03: 04: 05
Host_Ne tw ork
4c: 6e: 6e: 00: 39: b6
2c: b2: 1a: ca: be: cd
PHICOMM _6 66
AR-V400
4e: 6e: 6e: 5c: 10: b0
Host_Network
Signa l: Stron g
Enter y ou r passw or d
Enter y ou r passw or d
Cance l Co nfirm
Solid green
The extender is connected
to the router. Now you can
access the network.
Solid red
The extender has a problem
connecting to the router.
Please try relocating the
extender until the green light
is on.
LED Status Explanation:
AIRPHO_xxxx
WLAN
Sett ings WLAN
Disconnect any wired connection from your computer .
For Computer Users
AIRPHO_xxxx
AIRP HO_xxxx
connected
Click the Wi-Fi icon on the taskbar and connect to the
Extender’s network (e.g. AIRPHO_xxxx)
Connect to the Extender’s network
For Mobile Device Users
Go to Wi-Fi setting of your mobile device, and connect to
the Extender’s network (e.g. AIRPHO_xxxx)