Airrex HEPA-2000 User manual

▶ It is essential that you read ‘SAFETY INSTRUCTIONS’ carefully
before use and follow them at all times.
▶ This unit is specified for use on the rated voltage
power supply.
▶ We have a policy of continual improving on our products.
The contents (features and specifications) in this manual are
therefore subject to change without notice.
▶ The warranty form is on the last page. Please complete it now
and keep it in a safe place.
▶ Keep this manual on hand for reference.
▶ Thank you for purchasing the unit.
Before operation please read this user’s manual carefully.
MODEL : HEPA-2000
USER'S MANUAL
PORTABLE AIR SCRUBBER

2
TABLE OF CONTENTS
■ SAFETY INSTRUCTIONS
■ EXTERIOR DESCRIPTION
■ CONTROL PANEL FUNCTIONS
■ WIRING DIAGRAM & SPECIFICATIONS
■ FILTER & TROUBLE SHOOTING
■ WARRANTY
3
4
5
6
7
8

3
SAFETY INSTRUCTIONS
▶ Insert the power plug into the outlet for 220-240 V~, 50 Hz, 1 Phase.
▶ When inserting the power cord into the outlet, turn off the switch before use.
▶ Do not touch the product with a wet hand.
▶ Do not put anything heavy on the power cord.
▶ When water gets into the product or the electricity part, pull out the power plug
and dry it completely before use.
▶ Unplug the unit when during heavy lightning or electrical storms.
▶ Do not put the product at the humid place. It may occur a danger such as electric leak
or electric shock.
▶ Do not install it at the place where inflammable gas is generated.
It may occur a danger of explosion.
▶ Remove any obstacle at the inhaling hole and the exhaling hole.
▶ When cleaning the surface of the product, pull the power cord out, and use soft cloth
for preventing a scratch.
▶ Do not use wet cloth, wax or thinner.
▶ Do not put a hand or foreign substance into the inhaling hole or the exhaling hole.
It may occur a malfunction to the product or a physical injury.
▶ Pertaining to a risk of fire, electric shock, or injury to persons, for cleaning and
user-maintenance, such as lubrication.
▶ Warn the user to unplug or disconnect the appliance from the power supply
before servicing.
※ Keep this manual in a visible location near the unit for easy access.
The following instructions are for ensuring the user safety and to prevent any
physical injury or material damage. Please read carefully and follow all instructions.
WARNING AND CAUTION

4
EXTERIOR DESCRIPTION
Controller
Power cord hanger
12 inch
Duct flange
Handle
Filter door
HEPA filter
Fan
4 inch wheel
Pre filters

5
CONTROL PANEL FUNCTIONS
①
②
③
④
0
0.2
0.4
0.6
0.8
1.0
① Pressure Gauge
② Pressure Sensing Port
③ Circuit Breaker
④ Fan Speed (High / Off / Low) Switch
1. Before connecting the power cord, confirm the switch is turned off without fail.
2. For starting the product, press the switch in the control panel to the low or high.
3. For stopping the operation, press the OFF.

6
WIRING DIAGRAM
SPECIFICATIONS
MODEL HEPA-2000
Power Supply 220-240 V~, 50 Hz, 1 Phase
Power Consumption High : 1.13 kW / Low : 0.6 kW
Air Flow High : 1,360 CFM / Low : 1,135 CFM
Dimension (WxDxH) 724 x 762 x 762 mm
Weight 60 kg

7
Do not operate without the HEPA filter installed! Operating without the HEPA filter or using
non-approved power cords may cause damage to the electrical system or mechanical components.
Failure to comply will void all warranties.
PRE-FILTER PRE-FILTER PANEL HEPA FILTER
FILTER
TROUBLE SHOOTING
TROUBLE CHECK & REMEDY
The machine cannot be
operated Confirm that the power cord is correctly connected with the outlet.
After operating,
the power turns off.
Due to an over electric current, the power source is being cut.
Please check the circuit breaker.
Inhaling / exhaling is weak. Check if the filter is damaged or contaminated.
Dust is flowed out of
the exhaling hole. Check if the filter is damaged or correctly installed.
1. Size : 27.5 X 25.3 X 0.6 (inch)
2. The filter can collect dust of 10~30 ㎛
up to 20~85% in accordance with
the standard of weight method.
1. Size : 24.0 X 24.0 X 0.8 (inch)
2. Aluminum frame is put around
the outer edge. It can collect dust of
10~20 ㎛ up to 90% in accordance with
the standard of weight method.
1. Size : 24.0 X 24.0 X 5.9 (inch)
2. It can collect dust of 0.3 ㎛ up to
99.97% in accordance with the
standard of weight method.
1. At the time the pressure gauge value is 0.52 in high, and more than 0.42 in low.
2. At the time the filter is damaged due to a long-time use.
3. At the time the inhaling power falls due to a clogging in the filter.
■ TIME OF FILTER CHANGE
Time of filter change

● Designs and specifications of products are subject to change without prior notice for the improvement of products.
WARRANTY
AIRREX unit gives the more reliable performance, comfort and durability
the more they are used. They are built under a strict quality assurance regime
which includes inspection both during and after production and exhaustive
reliability testing.
In the unlikely event you have any problems, please contact your dealer or
distributor. If the problem is as a result of a production fault or failure, repairs will
be undertaken free of charge during the period of warranty subject to the
following warranty conditions:
1. If the problem has been caused by customer error or misuse, abuse or
damage, then all repairs will be charged for.
2. This warranty applies to your country.
3. Proof and date of purchase must be supplied.
4. Please complete the details below and keep this warranty in a safe place.
5. All transportation charges back to the dealer are at customer's cost. Keep all
original packaging to facilitate return. Return to customer will be at dealer's cost
(if genuine warranty claim).
Name of Company
Telephone No.
DISTRIBUTOR
Name :
Address :
Telephone :
CUSTOMER DETAILS
(Applicable to first retail purchaser only)
WARRANTY PERIOD ( ) Months
DESCRIPTION PORTABLE AIR SCRUBBER
MODEL HEPA-2000
DATE OF PURCHASE
PRODUCT
SERIAL NO.
Manufactured by
: HEPHZIBAH CO.,LTD.
(Juan-dong) 86, Gilpa-ro 71beon-gil,
Michuhol-gu, Incheon, Korea
TEL : [phone]
FAX : [phone]
E-mail : [email protected]
Website : www.airrex.biz