AKENORI NX1 User manual

User's Manual

1. Foreword.
2. Package content.
3. Device description.
4. Use of the dash camera.
4.1. Installation/removal.
4.2. Turning on of the device.
4.3. LED indication.
4.4. Recording/playback.
5. Dash camera control.
5.1. Operating with the dash cam using buttons on the device.
5.2. Wi-Fi clients for Android OS.
5.3. Сlient application for Apple iOS.
5.4. Connection to the dash camera from PC using browser.
5.5. Operating the device using LCD screen.
6. Video record playback with a GPS track on the map.
6.1. Below are the basic characteristics of the program.
6.2. Program installation.
6.3. Description of the program-user interface.
6.4. Program controls.
7. Alerts.
7.1. Use of the device.
7.2. Use of the SD Card.
8. Warranty obligations.
9. Specifications.
2
2
3
4
4
5
6
6
7
7
7
12
16
17
21
21
21
21
22
23
23
23
23
24

1. Foreword.
2
2. Package content.
Thank you for purchasing and using the AKENORI products!
Please read carefully the User's manual before you use the device.
1. Dash camera.
2. Car power adapter.
3. Set of cables to connect to the car mains or to the car adapter.
4. 16 GB Micro SDHC SD-card.
5. Windscreen holder of the device.
6. User's Manual.
7. Clearing napkin.
8. Spare parts for windscreen holder.
9. Screen with protective cover*.
10. HDMI cable*.
*Optional.
1
2
3 3
5
6
9
10
7
8
4

3. Device description.
1. Device on/off and recording
control button.
2. Wi-Fi on or off
(prolonged pressing).
3. Emergency record activation.
4. Operation mode indicator.
5. Mini USB connector.
6. HDMI connector.
7. SD Card slot.
8. RESET.
9. Lens tilt adjustment screw.
3
4
9
2
6
7
1
3
8
5

4. Use of the dash camera.
1. Place the dash camera below the rear-view mirror for better view.
2. Make sure that the windscreen section where the lens is installed
is within the wind-screen wiper reach.
3. Do not install the dash camera in the airbag location.
4. Do not attach the dash camera to the film tinted window, this may
damage the film.
5. Do not place the dash camera in the locations with obstructed view
caused by the tinting film, as well as close to interfering electronics.
1. Insert the dash camera into the holder.
2. Select an appropriate location for installation and attach the device
with the holder to the window by removing the protective film from
the holder's adhesive surface.
4. Adjust the field of view using the adjustment screw.
Note: Do not change the location of the device within 24 hours
to ensure the better fixing of the holder.
Remove the dash camera from the holder. For this, press slightly
the middle part underneath the holder and remove the holder by pulling
it from the bottom up.
4.1. Installation/removal.
Installation location.
Installation.
Removal.
4
Optimal location
for attachment Power
Connection to the car adapter

4.3. LED indication.
4.2. Turning on of the device.
- Recording start/stop.
- Wi-Fi on/off.
- Passage through the speed camera installation point.
Audible signals.
- Speed camera approach alert.
Voice announcement.
1. Connect the car charger to the lighter socket in your car.
2. Insert the SD Card into the SD-card slot.
3. Plug the USB cable into the USB slot. When the ignition is started,
the blue LED of recording must light up in a minute.
If this does not occur, reboot the device.
Power supply.
1. When the engine is started, the device automatically turns on,
and recording starts.
2. When the car engine is off, the device will automatically turn off within
20 seconds.
Note: The described function operates provided that the car electric
equipment is off completely.
Automatic turning on/off.
The date and time may be set manually or the automatic synchronization
with GPS satellites may be performed. The time zone must be specified
for the automatic synchronization in phone application (see in item 5).
Initial start.
5
Power on
Recording
Wi-Fi
LED color Value
The blue led is blinking or ON.
The blue LED is blinking.
The blue LED is ON.
The red LED is blinking.
The red LED is not blinking.
Power on.
The recording is not performed.
The recording is performed.
Wi-Fi on.
Wi-Fi off.

4.4. Recording/playback.
To start recording, press the REC button.
To stop recording, press the REC button again.
The REC button illuminates red during
recording.
*The archive may be reviewed and the settings
may be changed only when recording is off.
When the collision sensor activates at abrupt deceleration or acceleration,
the dash camera saves the record in a permanent (emergency) folder
on the SD-card. At least 20 seconds before the accident and 20 seconds
after it will be saved. Videos files will remain in the emergency folder even
if the SD-card is fill and old files are replaced in the cycle.
Recording in accordance with an acceleration (collision) sensor.
1. Install the SD-card, press the ON button to start recording.
2. Each recorded file lasts one minute (by default). When the SD-card is full,
old files will be overwritten with the new ones (starting from the first file).
3. Copying in case of collision. In case of collision (accident) the recorded
data will be copied to a special folder to protect against over-recording.
Recording performance.
Cyclic recording (by default).
6

5. Dash camera control
There are few methods to control and operate with the dash cam.
1 - When device is connected to power, you can switch it OFF by pressing
this button and holding during 10 seconds.
To switch ON the device after manual switching OFF - press the button
again and hold for 1 sec.
When device is working, press button 1 to stop/start the record.
2 - Press this button to switch ON/OFF WiFi Access Point on the dash cam.
3 - Press this button to switch ON the mode “Emergency record”.
1. To start your work, download the Akenori Mobile Client free application
from Google Play and install to your smartphone or tablet.
2. Make sure that Wi-Fi is enabled on the dash camera.
3. Start the application on the smartphone/tablet.
4. Check that no software update for the dash camera is found.
7
2
3
1
5.1. Operating with the dash cam using buttons
on the device.
5.2. Wi-Fi clients for Android OS.

5. Select the Akenori NX01 device in the connection list.
6. If you see the below screen, follow the instructions to connect
the dash camera.
8

Real-time camera image.
REC button to stop/start recording.
Date and duration of recording.
Button to save a current snapshot.
Button to add a current video to favourites.
Dash camera – Main operation mode.
Archive – Record archive review.
Favourites – Selected record review.
Settings – Dash camera settings.
About the device – Display of data on the device.
Main window of the application.
Interface description.
9