Alarm saf Cps100 User manual

I.Model Numbers

N/A4.0A28V360Transformer00634 17AH2.8A8ACPS100C - Cabinet00867 17AH2.8A8ACPS100-PCB00866

Max. Battery

Capacity

Max. AC Input

Current

Max. System

CurrentModel Number

Order

Number

12/24 VDC (field selectable), 8 power supplies for systems integration. Common access control and

security system applications include powering door strikes, mag locks, card readers and other

accessory devices.

II. Installation Instructions

1. Mount cabinet/board per mechanical dimensions and knockouts given in section III / VII.

2. Connect 120VAC,60 HZ., single phase to the black and white leads of the transformer in

accordance with Article 725 of the National Electrical Code , Article 16 of the Canadian Electrical

Code or other applicable codes.

3. Low Voltage AC Input - Connect to Secondary winding of the transformer. Transformer output

voltage is approximately 28VAC

4. Configure power supply output by positioning the appropriate jumpers

OFFONJ3 OFFONJ1 24V12V (Factory Default)

Output Voltage

5. Verify Output voltage by measuring output present at “DC1” output and “Battery “ terminals.

6. If optional batteries are present, connect battery set to “Battery” terminals (see Fig. IV). CAUTION:

Observe polarity; incorrect polarity may damage batteries. Recommended battery type -

PowerSonic (PS Series) or YUASA (NP - Series) sealed lead acid/gel cell.

7. Connect user system to “DC1” and/or FAI controlled “DC2” terminals. Caution: Observe polarity;

incorrect polarity may damage user system. Refer to Section 1 for Maximum Allowable Current.

8. FAI controlled Output (DC2) operation:

a. For power presence with a n/o circuit to FAI connector, set S1 to 1 & 3. (Default setting)

b. For power present on a n/c circuit to FAI, connector, set S1 to 2 & 3

9. AC and DC fault outputs are reported via Form “C” relays;

a. “AC” fault relay maximum contact switching : 30VDC/5A

b. ‘DC’ fault relay maximum contact switching : 30VDC/5A

10.Visual Indicators:

a. Green AC LED (D5) Low Voltage AC Presence

b. Green DC OK LED (D17) Regulator Voltage Output Presence

c. Red DC1 LED (D11) DC1 Output Voltage Presence

III. PCB Hookup Information

IV. Optional Battery Configuration

V. Troubleshooting

CPS100

CPS100C

Installation Instructions

AlarmSaf 65A Industrial Way, Wilmington MA 01887-3499, USA, Voice 978-658-6717, Fax 978-658 8638, www.alarmsaf.com Page 1 of 2, Rev A 52-227, 02/12/02

12 Volt B a tte ry 12 Volt B a tte ry

12 Volt Config u ra tion

12 Volt B a tte ry 12 Volt B a tte ry

24 Volt Config u ra tion

ParallelHook-Up SeriesHook-up

Remove system load. Verify

red LED is illuminated, check

system wiring

Replace unit

Short circuit in system wiring

Defective power supply

Red DS2 LED not illuminated

Remove system load. Verify

red LED is illuminated, check

system wiring

Replace unit

Short circuit in system wiring

Defective power supply

Red DS1 LED not illuminated

Replace Board

Check transformer connection

Loss of switcher voltage

Loss of input to switcher

Green DC LED not illuminated

Restore 120VAC

Replace Transformer

Loss of 120VAC

Loss of Low VAC

Green AC LED not Illuminated CorrectionPossible CauseSymptoms

VI. WIRING DIAGRAM

VII. CABINET MOUNTING AND KNOCKOUT POSITIONS

CPS100

CPS100C

Installation Instructions

AlarmSaf 65A Industrial Way, Wilmington MA 01887-3499, USA, Voice 978-658-6717, Fax 978-658 8638, www.alarmsaf.com Page 2 of 2, Rev A 52-227, 02/12/02

18.21

1.16

9.94

1.81

013.56

4.34

1.94 TYP

15.00

12.06

3.00

KEY LO C K

15.21