Alarmcom ADC-W110 User manual

PoE to Wi-Fi Bridge
Quick Start Guide
ADC-W110

1
Pre-installation checklist
• ADC-W110 PoE to Wi-Fi Bridge (included)
• Standard non-switched electrical outlet
• Broadband (Cable, DSL or Fiber Optic)
Internet connection with router
• A computer, tablet, or smartphone with Internet
access is required if the router does not have
the Wi-Fi Protected Setup (WPS) feature
• An Alarm.com Power over Ethernet
video camera with Ethernet cable
NOTE: There are two options for connecting the
W110 to the wireless network: Access Point (AP)
mode or Wi-Fi Protected Setup (WPS) mode. Use
WPS mode if you have easy access to the customer’s
router and the router has the WPS feature enabled.
Note that some Internet Service Providers disable
the WPS feature on customer routers. AP mode is
the most reliable method for installing this device.

2
AP Mode
Complete these steps to connect the W110
to a wireless network using AP mode.
1. Plug the W110 into an electrical outlet that is
within range of the customer’s Wi-Fi network.
Wait for the Wi-Fi LED to begin blinking white.
2. On an Internet enabled device, connect to the wireless
network “W110 (XX:XX:XX)” where XX:XX:XX is the last
six characters of the W110’s MAC address, which is
located on the back of the W110 or on the packaging.
3. On the same device, open a web browser and enter
“http://w110install” in the URL field. Follow the
on-screen instructions to add the W110 to the
wireless network. The Wi-Fi LED will turn solid white
and the Communication LED will turn solid green
when a successful connection is made.
4. Connect the PoE camera to the port at the
bottom of the W110 using an Ethernet cable.
5. Follow the installation instructions included
with the camera to add it to an account.
Connect the PoE to Wi-Fi Bridge
to the Wireless Network

3
WPS Mode
Complete these steps to connect the W110
to a wireless network using WPS mode.
1. Plug the W110 into a non-switched electrical outlet
that is within range of the customer’s Wi-Fi network.
Wait for the Wi-Fi LED to begin blinking white.
2. Press and hold the Communication button until
the Wi-Fi LED turns off and the Communication LED
begins blinking green (approximately 2 to 6 seconds).
3. Activate WPS mode on the router. The W110 will
begin to connect to the wireless network. The Wi-Fi
LED will turn solid white and the Communication
LED will turn solid green when a successful
connection is made.
4. Connect the PoE camera to the port at the
bottom of the W110 using an Ethernet cable.
5. Follow the installation instructions included
with the camera to add it to an account.
Connect the PoE to Wi-Fi Bridge
to the Wireless Network

4
LED reference guide
Device power
Device powered on
Solid Green
Device powered off
Off
Status
Successfully connected to the wireless network
Solid White
Solid Green
Local network connection only, connecting to Internet
Solid White
Blinking Green
❶Communication Button
❷ Power LED
❸ Wi-Fi LED
❹ Communication LED
❺ PoE Camera Port
❶
❹
❺
❷
❸

5
LED reference guide
Device power
Device powered on
Solid Green
Device powered off
Off
Status
Successfully connected to the wireless network
Solid White
Solid Green
Local network connection only, connecting to Internet
Solid White
Blinking Green
WPS mode
Off
Blinking Green
AP mode
Blinking White
Off
Error
No network found. See troubleshooting section.
Blinking Red
Off
Factory reset
Blinking Red
Blinking Red

6
Troubleshooting
If the W110 has already been added to a wireless
network (indicated by the W110 not entering AP mode
after powering on) and you want to change networks:
• To enter WPS mode, press and hold the
Communication button until the Communication
LED begins blinking green (approximately 2 to 6
seconds). Follow the WPS mode instructions from
step 3 on page 3.
• To enter AP mode, press and hold the Communication
button until the Wi-Fi LED begins blinking white
(approximately 7 to 11 seconds). Follow the AP
mode instructions from step 2 on page 2.
If you have issues connecting the W110 to the wireless
network, power cycle the device and try again. Also be
sure that the wireless network is working properly and
that you typed in the correct network password (SSID).

7
If the issues persist, try resetting the W110 to factory
defaults by holding down the Communication button for
12 seconds or until the Wi-Fi and Communication LEDs
begin blinking red. Try the installation instructions again.
WARNING: This will restore factory-default
settings to the device. Any associated
Wi-Fi networks will be removed.
The W110 is specifically designed for use with
Alarm.com Power over Ethernet video cameras.
Use with other devices is not recommended.
Questions?
Visit: www.alarm.com/supportcenter

8
Notices
FCC
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
ICS
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.

9

8281 Greensboro Drive
Suite 100
Tysons, VA 22102
190103
© 2019Alarm.com. All rights reserved.
Made in China.