Alcatel-Lucent Service Aggregation Router 7705 User manual

Alcatel-Lucent 7705
SERVICE AGGREGATION ROUTER | RELEASE 1.0
8-PORT ETHERNET ADAPTER CARD INSTALLATION GUIDE
Alcatel-Lucent Proprietary
This document contains proprietary information of Alcatel-Lucent and is not to be disclosed
or used except in accordance with applicable agreements.
Copyright 2008 © Alcatel-Lucent. All rights reserved.

When printed by Alcatel-Lucent, this document is printed on recycled paper.
Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is
subject to change without notice.
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All
other trademarks are the property of their respective owners.
Copyright 2008 Alcatel-Lucent.
All rights reserved.
Disclaimers
Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design
engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous
environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life-support machines, or weapons
systems, in which the failure of products could lead directly to death, personal injury, or severe physical
or environmental damage. The customer hereby agrees that the use, sale, license or other distribution
of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at
the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from
any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the
use, sale, license or other distribution of the products in such applications.
This document may contain information regarding the use and installation of non-Alcatel-Lucent
products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent
tries to ensure that this informationaccuratelyreflects informationprovided by the supplier, please refer
to the materials provided with any non-Alcatel-Lucent product and contact the supplier for
confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete
information provided about non-Alcatel-Lucent products.
However, this does not constitute a representation or warranty. The warranties provided for
Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by
Alcatel-Lucent and its customers.
This document was originally written in English. If there is any conflict or inconsistency between the
English version and any other version of a document, the English version shall prevail.

8-port Ethernet Adapter Card Installation Guide Page 3
Table of Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8-port Ethernet Adapter Card Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Provisioning Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Provisioning an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing and Replacing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installing and Removing SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Fiber Cable Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Locking Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SFP Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installing SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table of Contents
Page 4 8-port Ethernet Adapter Card Installation Guide

8-port Ethernet Adapter Card Installation Guide Page 5
List of Tables
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 1: Information Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 2: 8-port Ethernet Adapter Card Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 3: RJ-45 Port Pinouts—RJ-45 Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 4: Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 5: Adapter Card Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 6: SFPs for the 8-port Ethernet Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

List of Tables
Page 6 8-port Ethernet Adapter Card Installation Guide

8-port Ethernet Adapter Card Installation Guide Page 7
List of Figures
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 1: 8-port Ethernet Adapter Card Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 2: RJ-45 Connector Pin Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 3: 7705 SAR-8 Slot Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 4: Installing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 5: Removing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

List of Figures
Page 8 8-port Ethernet Adapter Card Installation Guide

8-port Ethernet Adapter Card Installation Guide Page 9
Preface
About This Guide
This guide provides site preparation recommendations and step-by-step procedures to
install, remove, and replace an 8-port Ethernet Adapter card.
Each 8-port Ethernet Adapter card has six RJ-45 ports and two small form-factor pluggable
(SFP) ports on its faceplate. The six RJ-45 ports are 10/100 Mb/s-capable ports that support
autosense and autonegotiation. The two SFP ports support 10/100/1000 Mb/s copper SFPs
or 100/1000 Mb/s fiber SFPs.
SFPs are hot-swappable input/output devices that plug into the adapter card ports, linking
the ports to fiber-optic or copper networks. Refer to SFPs on page 29 for a list of supported
SFP modules.
After the hardware installation process is completed, refer to the List of Technical
Publications for details on the boot process, software configuration, and Command Line
Interface (CLI) information to configure system and network parameters.
List of Technical Publications
The 7705 SAR OS documentation set is composed of the following guides:
• 7705 SAR OS Basic System Configuration Guide
This guide describes basic system configurations and operations.
• 7705 SAR OS System Management Guide
This guide describes system security and access configurations as well as event
logging and accounting logs.
• 7705 SAR OS Interface Configuration Guide
This guide describes card and port provisioning.

Preface
Page 10 8-port Ethernet Adapter Card Installation Guide
• 7705 SAR OS Router Configuration Guide
This guide describes logical IP routing interfaces, IP-based filtering, and routing
policies.
• 7705 SAR OS MPLS Guide
This guide describes how to configure Multiprotocol Label Switching (MPLS) and
Label Distribution Protocol (LDP).
• 7705 SAR OS Services Guide
This guide describes how to configure service parameters such as service access
points (SAPs), service destination points (SDPs), customer information, user
services, and Operations, Administration and Management (OAM) tools.
• 7705 SAR OS Quality of Service Guide
This guide describes how to configure Quality of Service (QoS) policy
management.
Warnings and Notes
Observe the warnings and notes to avoid injury or router damage during installation and
maintenance. Follow the safety procedures and guidelines when working with and near
electrical equipment. Warning statements and notes are provided in each chapter.
Audience
This guide is intended for network installers and system administrators who are responsible
for installing, configuring, or maintaining networks. This guide assumes you are familiar
with electronic and networking technologies.

Preface
8-port Ethernet Adapter Card Installation Guide Page 11
Information Symbols
Table 1 describes symbols contained in this guide.
Technical Support
If you purchased a service agreement for your 7705 SAR-8 and related products from a
distributor or authorized reseller, contact the technical support staff for that distributor or
reseller for assistance. If you purchased an Alcatel-Lucent service agreement, contact your
welcome center at:
Web: http://www1.alcatel-lucent.com/comps/pages/carrier_support.jhtml
Table 1: Information Symbols
Symbol Meaning Description
Danger This symbol warns that improper handling and installation could result in bodily
injury. Before you begin work on this equipment, be aware of hazards involving
electrical circuitry, be aware of your networking environments, and instigate
accident prevention procedures.
Warning This symbol warns that improper handling and installation could result in
equipment damage or loss of data.
Caution This symbol warns that improper handling may reduce your component or
system performance.
Note This symbol provides additional operational information.
Class 1 laser products are listed in the Class 1 laser adapter card documents.
Only approved Class 1 replaceable laser transceivers should be used with those
products.
Class 1 Laser Product

Preface
Page 12 8-port Ethernet Adapter Card Installation Guide

8-port Ethernet Adapter Card Installation Guide Page 13
Connector and LED Descriptions
In This Chapter
This chapter provides information on the following topics:
•8-port Ethernet Adapter Card Connectors and LEDs on page 14

8-port Ethernet Adapter Card Connectors and LEDs
Page 14 8-port Ethernet Adapter Card Installation Guide
8-port Ethernet Adapter Card Connectors and LEDs
Figure 1 shows the connectors and LEDs on the 8-port Ethernet Adapter card. Table 2
describes the features on the card.
Figure 2 shows the pin orientation for the RJ-45 ports (ports 1 through 6). Table 3 identifies
the pinout assignments.
Caution:
• This is a Class 1 laser product. Only approved Class 1 replaceable laser transceivers
should be used on this product.
Figure 1: 8-port Ethernet Adapter Card Connectors and LEDs
A8-ETN
Stat
Link 1 Act Link 2 Act Link 3 Act Link 4 Act Link 5 Act Link 6 Act 7
8
Link Act Link Act
Pwr
1 5
26
34
1959
4
Note: In Figure 1, port 1 is the left-most port on the card.
Table 2: 8-port Ethernet Adapter Card Features
Key Label Description
1 Stat(us) Green (blinking): Initializing
Green (solid): Operationally up, administratively up
Amber: Operationally down, administratively up; or hardware booting up
Unlit: Administratively down, shut down
2Pwr Blue: On
Unlit: No power or faulty power
3 RJ-45 ports The RJ-45 port number (1 through 6) is displayed below the port, between the
Link and the Act(ivity) silkscreen labels.

Connector and LED Descriptions
8-port Ethernet Adapter Card Installation Guide Page 15
Link Green: Link is up
Unlit: No link; operationally down; disabled or shut down
Act Amber (blinking): active (receiving or transmitting)
Unlit: Down or disabled
4 SFP ports The SFP port number (7 or 8) is displayed below the port. The associated Link
and Act(ivity) LEDs are located above the port.
Link Green: Valid communication link established
Unlit: Disabled, shut down; SFP optics installed but no link present; no SFP
Act Amber (blinking): active (receiving or transmitting)
Unlit: No activity
5 Ejector lever Rotate the ejector levers inward to insert the adapter card in the slot and outward
to release the card from the slot.
6 Captive screw Tighten both captive screws to secure the adapter card; loosen both screws to
remove the card.
Table 2: 8-port Ethernet Adapter Card Features (Continued)
Key Label Description

8-port Ethernet Adapter Card Connectors and LEDs
Page 16 8-port Ethernet Adapter Card Installation Guide
Figure 2: RJ-45 Connector Pin Orientation
Table 3: RJ-45 Port Pinouts—RJ-45 Female
Pin Signal Direction Description
1 TX+ Output Differential transmit data - positive
2 TX- Output Differential transmit data - negative
3 RX+ Input Differential receive data - positive
4 NC — Not connected
5 NC — Not connected
6 RX- Input Differential receive data - negative
7 NC — Not connected
8 NC — Not connected
Pin 8 Pin 1
1959
3

8-port Ethernet Adapter Card Installation Guide Page 17
Installing Adapter Cards
In This Chapter
This chapter provides information about installing and removing the adapter cards in the
7705 SAR-8.
This chapter provides information on the following topics:
•Provisioning Requirements on page 18
•Component Power Consumption on page 19
•Provisioning an Adapter Card on page 20
→Configuration Example on page 20
•Installation Procedures on page 23
→Warnings and Notes on page 23
→Installing an Adapter Card on page 24
→Removing and Replacing an Adapter Card on page 25

Provisioning Requirements
Page 18 8-port Ethernet Adapter Card Installation Guide
Provisioning Requirements
To configure cards and ports, you must be able to access the 7705 SAR-8 by console or
Telnet connection. Refer to the 7705 SAR-8 Installation Guide for information and
instructions on console and Telnet connections.
The CSM does not require provisioning. However, the IOM, which is an integral part of the
CSM software module, must be activated before any adapter cards and port parameters can
be provisioned and configured. The IOM is activated using the card and card-type CLI
commands to specify its slot number and card type. Adapter cards must be provisioned
before their ports can be configured.
Provision components in the following order:
1. Card slot number (use the card command)
2. Card type
3. Adapter card slot number (use the mda command)
4. Adapter card type
5. Ports
Notes:
• IOMs are specified using the card and card-type commands (items 1 and 2 in the list
below).
• Adapter cards are provisioned and configured using the mda and mda-type commands
(items 3 and 4 in the list below).

Installing Adapter Cards
8-port Ethernet Adapter Card Installation Guide Page 19
Component Power Consumption
Table 4 lists the power consumption for the chassis, CSM, and 8-port Ethernet Adapter card.
Refer to the 7705 SAR-8 Installation Guide for more information on the power consumption
of other components.
Table 4: Component Power Consumption
Component Conservative Estimate (Watts)
SAR-8 chassis
(unpopulated, all fans operating)
28 W
CSM 17 W
8-port Ethernet Adapter card 20 W

Provisioning an Adapter Card
Page 20 8-port Ethernet Adapter Card Installation Guide
Provisioning an Adapter Card
After the IOM has been activated on the CSM (Steps 1 and 2 below), continue in the
config context with the following CLI commands to provision the adapter card. The steps
below provision 8-port Ethernet Adapter cards in slots MDA 1 and 2. In Release 1.0, a
maximum of two 8-port Ethernet Adapter cards can be configured on a 7705 SAR-8 chassis.
Command Syntax Example
Step 1. card slot-number card 1
Step 2. card-type card-type card-type iom-1g
Note: In Release 1.0, the slot-number is always 1 and the card-type is always iom-
1g.
Step 3. mda mda-number mda 1
Step 4. mda-type mda-type mda-type a8-eth
Step 5. exit exit
To provision an additional adapter card, continue the configuration process with Step 6:
Step 6. mda mda-number mda 2
Step 7. mda-type mda-type mda-type a8-eth
Step 8. exit exit
Configuration Example
The following example displays the card, card-type, mda and mda-type commands to
specify the IOM as an iom-1g type, and provision 8-port Ethernet Adapter cards in slots
MDA 1 and 2.
ALU-1>config# card 1
ALU-1>config>card# card-type iom-1g
ALU-1>configcard# mda 1
ALU-1>config>card>mda# mda-type a8-eth
ALU-1>config>card>mda# exit
ALU-1>config>card# mda 2
ALU-1>config>card>mda# mda-type a8-eth
ALU-1>config>card>mda# exit