ALDI Tevion JS-W002 User manual
N13275
Wireless Headphone Set
Instruction Manual • Model Number JS-W002
1300 886 649
1After Sales Support
Telephone: 1300 886 649
Warranty 2
Welcome 3
General Safety Instructions 4
Assembly and Parts List 5
Getting Started 6
Instructions 8
Frequently Asked Questions 9
Other Useful Information 10
Contents
2
After Sales Support
Telephone: 1300 886 649
Wireless Headphone Set
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts for a
period of 12 months from date of purchase. Defects that occur within this warranty
period, under normal use and care, will be repaired, replaced or refunded at our
discretion, solely at our option with no charge for parts and labour. The benefits
conferred by this warranty are in addition to all rights and remedies in respect
of the product that the consumer has under the Competition and Consumer
Act 2010 and similar state and territory laws.
3After Sales Support
Telephone: 1300 886 649
Congratulations on choosing to buy a TEVION® product.
All products brought to you by TEVION® are manufactured to the highest
standards of performance and safety and, as part of our philosophy of customer
service and satisfaction, are backed by our comprehensive 1Year Warranty. We
hope you will enjoy using your purchase for many years to come.
Welcome
4
After Sales Support
Telephone: 1300 886 649
General Safety Instructions
Read this manual thoroughly before first use and keep it in a safe place for future
reference, along with the completed warranty card, purchase receipt and carton.
• Do not let the headphone set get wet.
• Do not place the headphone set near a water source.
• Do not use the headphone set if it is damaged. In case of damage, contact our
after sales support line for advice on repair or replacement.
• This product is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instructions concerning
use of the appliance by a person responsible for their safety.
• Supervise young children to ensure they do not play with the product.
• At the end of its working life, do not throw this product out with your household
rubbish. Observe local regulations and dispose of it appropriately for recycling.
Contact your local authorities for advice on recycling facilities in your area.
5After Sales Support
Telephone: 1300 886 649
9
10
Transmitter / charging base
Assembly and Parts List
Headphone set
1 Power ON/OFF switch
2 Power indicator
3 Volume +/-
4 Auto scan indicator
5 Auto scan button
6 Battery cover
7 Battery cover release
8 Transmitter / charging base
9 RCA audio cable
10 Power adaptor
Red LED (signal indicator)
Green LED (charge indicator)
1
3
4
5
6
7
2
8
6
After Sales Support
Telephone: 1300 886 649
Getting Started
Before first use
• Remove all packaging materials from the product and dispose of them
responsibly. Plastic wrapping can be a suffocation hazard for babies and young
children, so ensure all packaging materials are out of their reach.
• Inspect the mains power adaptor for damage. Do not use the product if the
adaptor or its cord have been damaged or are not working properly. In case of
damage, contact the after sales support line for advice.
Transmitter / charging base connections
• Connect the mains power adaptor (supplied) to an electrical outlet.
• Connect the mains adaptor cable to the DC IN input socket at the back of the
transmitter/charging base.
• Using the supplied RCA audio cable, connect the transmitter to the relevant
audio outputs on your TV, hi-fi or other relevant audio component.
As soon as you have connected both the power adaptor to the mains outlet and
the audio cable to a signal source, the red LED signal indicator will light up. If it
remains off, switch on the audio source and increase its output level until the red
indicator light comes on.
Receiver headphone set
• Remove the battery cover from the left side (L) of the receiver headphone set.
• Insert two rechargeable AAA size batteries (supplied), taking care to ensure
correct polarity.
• Put the battery cover back onto the left side of the receiver headphone set.
• Switch off the receiver headphone set and place it into the transmitter to
charge the batteries for 24 hours before initial use. (See page 7 for more on
charging batteries.)
7After Sales Support
Telephone: 1300 886 649
Getting Started (Cont.)
Charging batteries
• Switch off the receiver headphone set.
• Place the headphone set on the transmitter, taking care to ensure that the
charge contacts touch the transmitter’s charge pins and the green charging
indicator is on.
• The charge process starts automatically.The green indicator light comes on and
will stay on during charging.
NOTE: Make sure to charge new batteries for 24 hours before using them for
the first time in the headphone set.
WARNING:
• The headphone set is designed for use with two rechargeable AAA size (LR03)
batteries only (supplied). Never use it with another type of battery or with non-
rechargeable batteries.
• Never attempt to recharge conventional (non-rechargeable) dry cell batteries.
• The batteries must be fully charged before first use. An initial 24 hour charge is
required to guarantee an acceptable service life for the rechargeable batteries.
• Always ensure that the headphone set is switched off while the batteries are
charging.
• When the headphone set is not in use, switch it off to avoid damaging the
batteries.
• When replacing the rechargeable batteries, or when disposing of the unit, make
sure to comply with any laws that apply in your area relating to the disposal of
batteries. Place the batteries in an appropriate disposal container to ensure that
they are eliminated safely and in an environmentally-friendly way, or contact
your local authorities for advice on recycling facilities in your area.
8
After Sales Support
Telephone: 1300 886 649
• Set up the unit as described in the “Getting Started”section on page 6.
• Turn on the audio source (TV set, hi-fi system or any other audio device) that is
connected to the transmitter.
• Switch on the headphone set.
• Place the headphones on your head and adjust the volume to obtain the
desired sound level.
• If you cannot find the best reception frequency, press the“Auto Scan” button on
the headphones to get the fine scanned channel.
• You should now be able to move around freely from one room to another
without any interference. If interference does occur (interruptions in the signal),
press the“Auto Scan” button once to find a better reception channel.
NOTE: For better stereo reception, stay approximately seven metres away from
the transmitter when you press the “Auto Scan” button.
• If it is impossible to find a satisfactory frequency, change the channel setting
at the back of your transmitter, then press the“Auto Scan” button on the
headphones to find the corresponding channel.
NOTE: To both protect the transmitter and save power, the transmitter will
automatically switch off after approximately four minutes if there is no audio
signal, or if the signal received from the audio source is too weak for proper
reception. It will automatically switch back on if the signal returns to an
acceptable level.
Instructions
9After Sales Support
Telephone: 1300 886 649
No sound
• Ensure that the plug of the mains adaptor is pushed fully into the power outlet
and that its output jack is properly connected to the DC IN 6V socket at the
back of the transmitter.
• Ensure that the headphone ON/OFF switch is switched to the ON position.
• The headphone’s battery charge level may be too low. Recharge the batteries
or replace them with fully charged rechargeable batteries.
• Ensure that your TV set, hi-fi system or audio component is switched on and set
to a channel that broadcasts an audio signal.
• Use the headphone volume control to increase the sound level.
• The connected audio/video equipment may not be in playback mode. Start
playback on the equipment.
• The headphone’s output level may be set too low. Adjust the volume to a
suitable level.
Distortion
• If distortion appears, press the“Auto Scan” button again.
• Use the channel selector (at the back of the transmitter unit) to change the
transmission frequency, then adjust the tuning control by pressing the“Auto
Scan”button on the headphone set.
• The headphone’s battery charge level may be too low. Recharge the batteries
or replace them with fully charged rechargeable batteries.
• Ensure that the volume setting is correct.
• The headphone set may be too far away from the transmitter. Move closer to it.
• The audio signal input level may be too low. Increase the volume at the audio
source (TV, hi-fi system etc.).
Frequently Asked Questions
10
After Sales Support
Telephone: 1300 886 649
Features
• 900 MHz RF technology
• Auto scanning system on headphone
• Phase Lock Loop (PLL) transmission system on transmitter
• Automatic battery recharging
• RF technology leaves you completely free to move around
• Transmission is not restricted solely to line of sight
• Rechargeable receiver headphone set
• Charger built into the transmitter
• High quality stereo sound that is virtually interference-free
• Auto on/off function
Technical specifications
Transmission mode UHF stereo
Carrier frequency 900MHz
Operating voltage Transmitter: 6V 300mA
Receiver: 2.4V
2 rechargeable batteries, LR03/AAA size (supplied)
Frequency response 40Hz - 11kHz
Distortion 1%
Signal to noise ratio 65dB
Channel separation 30dB
Range 70m (open area)
Other Useful Information
After Sales Support
Telephone: 1300 886 649
Table of contents
Other ALDI Headphones manuals
