ALFAtron ALF-WP70T/RS User manual

www.alfatronelectronics.com
ALFATRON ELECTRONICS GmbH GERMANY
ALF-WP70T/RS

ALF-WP70T/RS
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1- this device may not cause interference, and
2- this device must accept any interference, including interference that may
cause undesired operation of thedevice.

ALF-WP70T/RS
Radiation Exposure:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment.
Do not dispose of this product with the normal household waste at the end of its
life cycle. Return it to a collection point for the recycling of electrical and
electronic devices. This is indicated by the symbol on the product, user manual or
packaging. The materials are reusable according to their markings. By reusing,
recycling or other forms of utilisation of old devices you make an important
contribution to the protection of our environment. Please contact your local
authorities for details about collection points.
Preface
This manual describes the functions, installation and operation principles and
methods of the product in detail. Before installing and using this product, please
read it carefully.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged due to
electrical spikes, surges, electric shock, lighting strikes, etc. The use of surge
protection systems is highly recommended in order to protect and extend the life of
your equipment.

ALF-WP70T/RS
Table of Contents
1. Introduction. ............................................................................................. 1
2. Features. ................................................................................................... 1
3. Package Contents. ..................................................................................... 1
4. Specifications. ........................................................................................... 2
5. Product Dimensions................................................................................... 4
6. Operation Controls and Functions. ............................................................. 5
6.1 Transmitter Panel................................................................................ 5
6.2 Receiver Panel..................................................................................... 6
7. Application Example. ................................................................................. 7
8. After-Sales Service……………………………………………………………………………………….8
9. Warranty……………………………………………………………………………………………………..9

- 1 -
ALF-WP70T/RS
1. Introduction
The ALF-WP70T/RS wall plate is a 2x1 switcher and HDBaseT transmitter with
HDMI and USB-C inputs. It features a US one-gang enclosure for Decora-style wall
plate openings with interchangeable black and white wall plates and faceplates.
Supports video resolution up to 4K2K@50/60Hz 4:4:4. It supports bidirectional RS-
232 pass-through, and the RS-232 control signal can be transmitted up to 131ft /
40m. The product is remotely powered by the receiver or other HDBaseT-
equipped devices via POE.
2. Features
•Compliant with HDMI 2.0b, HDCP 2.2 and Display Port 1.2a
•HDMI input supports 18Gbps video bandwidth; USB-C input supports 5.4Gbps
video bandwidth
•Video resolution up to 4K2K@50/60Hz 4:4:4
•HDBaseT output can extend video transmission distance up to 230ft / 70m for
1080P@60 or 131ft / 40m for 4K@60 via a single CAT6/6a/7 cable
•Support 3D, HDR10 and Dolby Vision
•HDMI audio formats support LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS,
DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
•Supports HDMI and USB-C input
•With USB-C charging port
•US one-gang enclosure for Decora-style wall plate openings
•Input signal selection supports automatic mode and manual mode
•Support POE function (only from Receiver to Transmitter)
•Available in white or black coating
3. Package Contents
•1 × 18Gbps HDBaseT 230 ft / 70M with USB-C/HDMI Wall Plate Transmitter
•1 × 3pin-3.81mm Phoenix Connector (male)
•1 × User Manual

- 2 -
ALF-WP70T/RS
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliance
HDCP 2.2
DP Compliance
Display Port 1.2a
Video Bandwidth
USB-C: 5.4 Gbps
HDMI: 18 Gbps
Video Resolution
480i~1080p50/60Hz, 4Kx2K@24/30Hz, 4k2k@60Hz
Color Space
RGB, YCbCr 4:4:4 / 4:2:2, YUV 4:2:0
Color Depth
8/10/12-bit (1080P@60Hz)
8-bit (4K@60Hz)
HDR
Support
HDMI Audio Formats
LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-
EX, DTS-96/24, DTS High Res, DTS-HD
Master Audio, DSD
Transmission
Distance
Max distance (1080P): 230ft / 70m over CAT6/6a/7 Max
distance (4K): 131ft / 40m over CAT6/6a/7
ESD Protection
Human body model — ±8kV (Air-gap discharge) &
±4kV (Contact discharge)
Connection
Transmitter
Inputs: 1x HDMI Type A [19-pin female]
1x USB-C
Outputs: 1x HDBaseT Out [RJ45, 8-pin female]
1x USB-C (only for charging)
Controls: 1x RS-232 [3-pin phoenix connector]
1x FW [Micro USB, Update port]

- 3 -
ALF-WP70T/RS
Receiver
Inputs: 1x HDMI IN [Type A, 19-pin female]
1x HDBaseT IN [RJ45, 8-pin female]
Outputs: 1x HDMI OUT [Type A, 19-pin female]
1x AUDIO OUT [Phoenix jack]
Controls: 1x RS-232 [3-pin phoenix connector]
1x FW [Micro USB, Update port]
Mechanical
Housing
Metal Enclosure
Color
White / Black
Dimensions
Wall plate:
33.3mm [W] x 65.7mm [D] x 68.7mm [H]
Faceplate:
69.9mm [W] x 3mm [D] x 114.3mm [H]
Receiver:
200mm [W] x 102.8mm [D] x 22mm [H]
Weight Wall plate: 197g, Receiver: 517g
Power Supply
POE (only from Receiver to Transmitter)
Power Consumption
Wall plate: 7.92W (Max), Receiver: 6W (Max)
Operating
Temperature
32 - 104°F / 0 - 40°C
Storage Temperature
-4 - 140°F / -20 - 60°C
Relative Humidity
20 - 90% RH (no condensation)

- 4 -
ALF-WP70T/RS
5. Product Dimensions
69.9
Front
60.9
Side
33.3
Back
Unit: mm
114.3
68.7

- 5 -
ALF-WP70T/RS
6. Operation Controls and Functions
6.1 Transmitter Panel
No.
Name
Function Description
1
Power LED
The power LED indicator will illuminate green when
the
device is powered on, and red when the unit is
in standby.
2 HDMI LED
When the HDMI input port is active and the HDMI
signal is detected, the green LED will be on.
3 USB-C LED
When the USB-C input port is active and USB-C
signal is detected, the green LED will be on.
4
HDMI port
HDMI input port, connect to an HDMI source device.
5
USB-C port
(1) USB-C signal input port.
6 Power Input port
Connect this port to a compatible power supply,
the USB
-C port will charge the connected device
from the USB-C port (5).
7 RS-232 port
Connect to PC or control system for bidirectional RS-
232 control signal passthrough.
8
SOURCE button
Used to switch between HDMI / USB-C input signal.
9
HDBaseT OUT
Connect to the HDBaseT IN port of Receiver with a
CAT6/6a/7 cable.
10
FW port
Firmware update port.

- 6 -
ALF-WP70T/RS
.
6.2 Receiver Panel
No.
Name
Function Description
1 Power LED
When the product is powered on, the red LED
indicator will be on.
2 DC 24V
DC 24V power supply port.
3
FW
Firmware update port.
4 HDBaseT IN
Connect to the HDBaseT OUT port of the Transmitter
with a CAT6/6a/7 cable.
5
HDMI OUT
HDMI output port, connect to HDMI display device.
6 HDMI IN HDMI input port, connect to HDMI source device.
7 AUDIO OUT Analog audio output port.
8 RS-232 port
Connect to PC or control system for bidirectional
RS-232 control signal pass-through.
Note:
This transmitter supports automatic/manual mode for source signal input. In
manual switching mode, press the SOURCE button to select HDMI/ USB-C input
source.
In automatic switching mode, the last connected or the currently connected
source signal will be selected automatically. When both HDMI and USB-C ports are
connected to active signal, HDMI signal input takes preference. When both HDMI
and USB-C ports are not connected to an active signal, it will switch to the source
signal of the Receiver.

- 7 -
ALF-WP70T/RS
7. Application Example

- 8 -
ALF-WP70T/RS
After-sales Service
Should you experience problems using the Alfatron ALF-WP70T/RS please refer to
the manual and operation controls and functions (6). Should the error persist,
note that any transport costs of the equipment to the distributor are borne by the
user during the warranty.
Product Limited Warranty: Alfatron warrants that its products will be free from
defects in materials and workmanship for seven years, which starts from the first
day of purchase.
Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the unit is within the warranty period must be presented to obtain
warranty service.
What the warranty does not cover (servicing available for a fee):
•Warranty expiration.
•Factory applied serial number has been altered or removed from the
product.
•Damage, deterioration, or malfunction caused by:
•Normal wear and tear.
•Use of supplies or parts not meeting product specifications.
•No certificate or invoice as the proof of warranty.
•The product model showed on the warranty card does not match with the
product or if the product had been altered.
•Damage caused by force majeure.
•Servicing not authorized by Alfatron.
•Any other causes which do not relate to a product defect.
•Delivery, installation or labour charges for installation or setup of the
product.
Technical Support: Contact our after-sales department at
www.alfatronelectronics.com

- 9 -
ALF-WP70T/RS
Warranty
1.1 This limited warranty covers defects in materials and workmanship in this
product.
1.2 Should warranty service be required, proof of purchase must be presented to
the Company. The serial number on the product must be clearly visible and not
have been tampered with in any way whatsoever.
1.3 This limited warranty does not cover any damage, deterioration or
malfunction resulting from any alteration, modification, improper or
unreasonable use or maintenance, misuse, abuse, accident, neglect, exposure to
excess moisture, fire, improper packing, and shipping (such claims must be
presented to the carrier), lightning, power surges, or other acts of nature. This
limited warranty does not cover any damage, deterioration or malfunction
resulting from the installation or removal of this product from any installation,
any unauthorized tampering with this product, any repairs attempted by anyone
unauthorized by the Company to make such repairs, or any other cause which
does not relate directly to a defect in materials and/or workmanship of this
product. This limited warranty does not cover equipment enclosures, cables or
accessories used in conjunction with this product.
This limited warranty does not cover the cost of normal maintenance. Failure of
the product due to insufficient or improper maintenance is not covered.
1.4 The Company does not warrant that the product covered hereby, including,
without limitation, the technology and/or integrated circuit(s) included in the
product, will not become obsolete or that such items are or will remain
compatible with any other product or technology with which the product may be
used.
1.5 Only the original purchaser of this product is covered under this limited
warranty. This limited warranty is not transferable to subsequent purchasers or
owners of this product.
1.6 Unless otherwise specified, the goods are warranted in accordance with the
manufacturer’s product specific warranties against any defect attributable to
faulty workmanship or materials, fair wear and tear being excluded.
1.7 This limited warranty only covers the cost of faulty goods and does not
include the cost of labor and travel to return the goods to the Company’s

- 10
ALF-WP70T/RS
premises.
1.8 In the event of any improper maintenance, repair or service being carried out
by any third persons during the warranty period without the Company’s written
authorization, the limited warranty shall be void.
1.9 A 7 (seven) year limited warranty is given on the aforesaid product were used
correctly according to the Company’s instructions, and only with the use of the
Company’s components.
1.10 The Company will, at its sole option, provide one of the following three
remedies to whatever extent it shall deem necessary to satisfy a proper claim
under this limited warranty:
1.10.1 Elect to repair or facilitate the repair of any defective parts within a
reasonable period of time, free of any charge for the necessary parts and labor to
complete the repair and restore this product to its proper operating condition.; or
1.10.2 Replace this product with a direct replacement or with a similar product
deemed by the Company to perform substantially the same function as the
original product; or
1.10.3 Issue a refund of the original purchase price less depreciation to be
determined based on the age of the product at the time remedy is sought under
this limited warranty.
1.11 The Company is not obligated to provide the Customer with a substitute unit
during the limited warranty period or at any time thereafter.
1.12 If this product is returned to the Company this product must be insured
during shipment, with the insurance and shipping charges prepaid by the
Customer. If this product is returned uninsured, the Customer assumes all risks of
loss or damage during shipment. The Company will not be responsible for any
costs related to the removal or re-installation of this product from or into any
installation. The Company will not be responsible for any costs related to any
setting up this product, any adjustment of user controls or any programming
required for a specific installation of this product.
1.13 Please be aware that the Company’s products and components have not
been tested with competitor’s products and therefore the Company cannot
warrant products and/or components used in conjunction with competitor’s
products.

- 11
ALF-WP70T/RS
1.14 The appropriateness of the goods for the purpose intended is only warranted
to the extent that the goods are used in accordance with the Company’s
installation, classification, and usage instructions.
1.15 Any claim by the Customer which is based on any defect in the quality or
condition of the goods or their failure to correspond with specification shall be
notified in writing to the Company within 7 days of delivery or (where the defect
or failure was not apparent on reasonable inspection by the Customer) within a
reasonable time after discovery of the defect or failure, but, in any event, within 6
months of delivery.
1.16 If delivery is not refused, and the Customer does not notify the Company
accordingly, the Customer may not reject the goods and the Company shall have
no liability and the Customer shall pay the price as if the goods had been
delivered in accordance with the Agreement.
1.17 THE MAXIMUM LIABILITY OF THE COMPANY UNDER THIS LIMITED
WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE
PRODUCT