Algo 8301 Quick setup guide

1
Paging Adapter Amplifier Integration Guide
Algo Support, 604-454-3792
[e-mail]
www.algosolutions.com 2019-06-20 v1.5

2
Table of Contents
➢Paging Adapter Hardware Interface
▪8301 Paging Adapter & Scheduler………………….………………...5
▪8373 Zone Paging Adapter………………………………….……….....6
▪Hybrid IP & Analog Infrastructure Integration……………………...8
➢Paging Amplifier Wiring Diagrams
▪AT&T/Lucent PagePal with 8301……………………………..………10
▪AT&T PagePac 20 PowerMate ……………………………………...…11
▪Bogen TPU-35/60/100/250 with 8301…………………….……………12
▪Bogen TPU-35/60/100/250 with 8373…………………………….……13
▪Bogen PCM2000 with 8301……………...………….…………………..14
▪Bogen C35/C60/C100 with 8301………...………….………………….15
▪Valcom V-2001a with 8301………………...………………….………...16
▪Valcom V-2003a with 8301……………………………………..............17

3
Table of Contents
➢Paging Amplifier Wiring Diagrams (continued)
▪Valcom V-2006a with 8301……………………………………………..18
▪Valcom V-9940 with 8301……………………………………………….19
▪Valcom V-9941A with 8301 ……………………………………………..20
▪Valcom V-1109RTVA with 8301……………………………..………… 21
▪Valcom V-1094A with 8301…………………………………….………. 22
▪Valcom V-2924A with 8301 ……………………………………………..23
▪Viking PA-2A with 8301………………………………………….………24
▪Viking PA-15 with 8301………………………………………….……….25

4
Paging Adapter
Hardware Interface

5
8301 Paging Adapter & Scheduler
Music Input
➢SIP (50 Page ext., 10
Emergency Alert ext. &
10 Ring ext.)
➢Multicast Send &
Receive
➢Scheduler for
Automated Tones &
Announcements
➢1GB Memory

6
8373 Zone Paging Adapter
➢SIP (50 Page ext.)
➢Switches up to 280W
using one 70V amplifier
➢Multicast Send &
Receive

7
8373 Zone Paging Adapter

Analog Amplifier &
Speakers
Simultaneous Multicast
To Speakers, Strobes &
Phones
Hybrid IP & Analog Infrastructure
Integration
Simultaneous
Line Level Output
to Amplifier
SIP Call
8

9
Paging Amplifier
Wiring Diagrams

10
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line
Out' Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8301 Installation Example with
AT&T/Lucent PagePal
Set the PagePal to DL (Dry Loop) mode using the
switch in the front

11
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line
Out' Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8301 Installation Example with
AT&T PagePac 20 PowerMate

12
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8301 Installation Example with
Bogen TPU-35/60/100/250

13
On the 8373 web interface, go to Basic Settings -> Features and set the 'Line Out'
Analog Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8373 Installation Example with
Bogen TPU-35/60/100/250
The 8373 is designed to provide a Line Out for audio to
a traditional amplifier.
Loop the power of the amplifier into the 8373 to
switch up to 280w into 1-3 audio channels.
The speaker runs will be connected to the channel
outputs on the 8373.

14
Before connecting, power off PCM2000 system. Set the dip switch as
demonstrated above (CC switch down and P/P switch middle)
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.
To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).
8301 Installation Example with
Bogen PCM2000

15
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8301 Installation Example with
Bogen C35/C60/C100

16
8301 Installation Example with
Valcom V-2001a
The 8301 Line Out (terminal 3 and 4) connects to either the
Tip and J3) using an RJ11 modular connector or the Page T
and Page R inputs on the Valcom V-2001A Amplifier via a 2-
wire connection to the terminal strip.
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line
Out' Analog Output Level to “-10dBm 600 ohm (0.245 Vrms)”.
SW1 Off for Page Port Access

17
On the Valcom V2003a, set the dip switch SW3. Set
10, 7, 4 in the off position (up position). SW2 in the off
position.
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”.
To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).
8301 Installation Example with
Valcom V-2003a

18
Set the he Battery Feed switch to off for Page Port
access on the V2006a
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “-10dBm 600 ohm (0.245 Vrms)”.
To play DTMF tones and control the zones, make sure to enable Generate In-Band DTMF
Tones (Advanced Settings -> Advanced Audio).
8301 Installation Example with
Valcom V-2006a

19
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “-20dBm 600 ohm (0.077 Vrms)”.
8301 Installation Example with
Valcom V-9940
Ensure that only DIP Switches 1 and 8 are ON. If the
device is not working try turning DIP Switch 1 OFF.

20
On the 8301 web interface, go to Basic Settings -> Features and set the 'Line Out' Analog
Output Level to “0dBm 600 ohm (0.775 Vrms)”.
8301 Installation Example with
Valcom V-9941A
Note there will be no talk back from the Valcom
speakers.