Algolith Dual SD/HD Frame Synchronizer FRS-1002-MD User manual

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
About this manual...
Overview.
Main Features.
Main Features.
Main Features .
The Algogear Series
Static Discharge.7
Board Installation.7
Proc Amp.21
Legalizer.21
Audio Setup Window.22
Audio mixing Window.23
The Alarm Setup Window.26
Load the new product onto your card.28
Power Consumption.9
Front Module.9
Rear Input / Output Module Labels.10
Output Channels.11
Controls.12
Card Info & Card Status.12
Product Status Area.12
The Dashboard Software Interface.12
The Basic Tree View Window.13
The Product Status Area.13
The Card Info Window.13
Valid License List.13
The Card Status Window.14
Control.14
Login to administrator level.15
Adjusting Parameters.15
The Administrator Level.15
Recall & apply settings.16
Save settings.16
The Card Setup Window.16
Selecting the Reference.17
Video Setup Window.19

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
About this manual
This user guide covers both the FRS-1002-MD and FRS-1002-MD-LG-PA
cards. The FRS-1002 cards share many common features and the general
content of this user guide applies to both products. Content and features
fa fa
1^^9^94,To8(^!"7^p/M!T20^9 f !H^oIv50, l, 576^50^d
sa'SSISSrSEiKss
increments. Up to 11 additional frames of delay can be added in HD.
b “ i "
1 " 4 1
Main Features

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA
MD
LG-PA
Main Features
The FRS-1002-MD-LG-PA has all the features of the FRS-1002-MD, plus:
• Adjustable brightness, contrast, saturation, and hue (SD only)
• Programmable video legalizer
The graphic below represents a functional block diagram of the FRS-
1002-MD-LG-PA.

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to
The Algogear Series
The list of Algogear applications is quickly evolving. Visit www.algolith.
com fora current list of available applications and news about products

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA
H
Static Discharge
A Whenever handling the FRS-1002 and other related equipment, please
observe all static discharge precautions as described in the following
note:
Static discharge can cause serious damage to sensitive semiconductor
devices. Avoid handling circuit boards in high static environments such
as carpeted areas, and when wearing synthetic fiber clothing. Always
exercise proper grounding precautions when working on circuit boards
and related equipment.
Board Installation
Use the following procedure to install the FRS-1002 in an openGear (DFR-
8310-N) distribution frame with cooling fans:
A Due to power consumption and heat dissipation requirements, the
FRS-1002 must only be installed in a frame with the cooling fan option
installed.
1. Refer to the User Manual of the openGear 8300 series frame
to ensure that the frame is properly installed according to
instructions.
A 2. A maximum of 8 FRS-1002 or other Algogear cards can be
installed in the DFR-8310 series frame.
Do not populate the openGear frame with more than 8 Algogear
cards. Attempting to do so may damage the cards, the frame
3. After selecting the desired frame and installation slot, hold the
FRS-1002 card by the edges and carefully align the card edges
with the slots in the frame. Then fully insert the card into the
frame until the rear connection plugs are properly seated on
the midplane and rear modules.

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
m
The FRS-1002 card requires a BNC rear output module. Depending on the
frame model you purchased, your frame may be equipped with a fixed 100
BNC rear panel.
Your frame model may have a modular rear panel, to accommodate different
types of cards. You will then need to purchase and install a 10 BNC single rear
module for each FRS-1002 card in your openGear frame.

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA
Power Consumption
than 8 slots.
Front Module

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
6 status LEDs are located near the FRS-1002 card’s front edge.
Consult the graphic and color code below to identify the LEDs and their
meanings
Rear Input / Output Module Labels
Algolith’s FRS-1002 card comes with the rear module labels of every
available Algogear product at the time of purchase. To identify your card
and the connectors at the back of the openGear frame, simply push the
appropriate label onto the BNC connectors to identify the card's inputs
and outputs.

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA
Output Channels
The FRS-1002 has 2 HD/SD-SDI inputs and 4 HD/SD-SDI outputs. Each
channel in the Dashboard user interface corresponds to the matching
input number. The label on the card's BNC rear output module, at the back
of the openGear frame, identifies the inputs and outputs.
► ,A @
► ,B @
► 2A 0
► B ©

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
e, the FRS-1002 card is ct
SITS S SKt
sthey

Guide to installation and opera

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
The Card Status Window
The Card Status window displays the input video format for each channel,
the input audio format for each channel, and the reference video input.
Control
The user can control the FRS-1002 card’s various parameters in the
Card Setup, Video Setup, Audio Setup and Alarm Setup windows.
The following section describes how to adjust the parameters.

FRS-1002-MD / FRS-1002-MD-LG-PA
The Card Setup Window

i installation and operation
Selecting the
is automatically saved and will be restored after power-up.
SXta one video

FRS-1002-MD / FRS-1002-MD-LG-PA
Guide to installation and operation
External Card (BNC 10): Uses the reference signal from the FRS-1002
card’s rear module REF input.
External 1 (Frame ref 1) External Card (BNC 10)

Guide to installation and operation
FRS-1002-MD / FRS-1002-MD-LG-PA
:asd«r ISjESESSits 5 ”

FRS-1002-MD / FRS-1002-MD-LG-PA