AliMed ONE User manual

Figure 5
PAIR indicator
located on
right side of
Motion Sensor
Match PAIR on Motion Sensor
to PAIR on Base
1. Universal Status Indicator
Illuminates at varying times:
when Motion Sensor is turned
on, pairing with Alarm Base is
complete, or infrared beam is
broken
2. Infrared Motion Sensor
Infrared beam detects motion
3. On/Off Switch Turns Motion
Sensor on or off
4. Pair Status Indicator
Illuminates when Alarm Base
is in range for pairing
5. Battery Compartment
Button Press to open battery
compartment
6. Universal Wall Mount and
Bracket Holds Motion Sensor
and mounts to wall
Intended Use
Key Features
The AliMed ONE Wireless Motion Sensor pairs with the Alarm Base to provide caregiver notication of patient falls or elopement as part of an overall fall
management program. The Motion Sensor can be mounted to a wall for wandering protection anywhere in the room.
Figure 1
2.
5.
1.
6.
Setup and Operating Instructions
The Motion Sensor is installed by Nurse or Biomedical staff.
1. Motion Sensor requires one (1) 9V battery to operate (sold separately, see reverse).
2. Press the Battery Compartment Button (Fig. 3) to open the battery compartment.
3. Align the male and female connectors on the top of the battery to the connectors
attached to the unit. Place in battery compartment.
4. The Motion Sensor is now ready for pairing.
5. Close the battery compartment door until it snaps into place.
Pairing the Motion Sensor with the Alarm Base:
1. Ensure the On/Off Switch is set to the “OFF” position (Fig. 2).
2. Press Pair Button on the Alarm Base.
3. The Base will beep and the rst open channel will blink green and red indicating
channel is ready for pairing.
4. Place Motion Sensor next to the Base matching PAIR on the Motion Sensor to PAIR
on the Base (Fig. 4). Note: Pair Status Indicator on Motion Sensor (Fig. 3) will
illuminate when in range of the Base.
5. If pairing is successful, the Base will beep and the assigned channel will blink green
once. The Universal Status Indicator (Fig. 1) on Motion Sensor will blink three (3)
times.
6. The Motion Sensor is now paired with the Base. The assigned channel on the Base
will continuously blink at approximately 5-second intervals indicating Motion Sensor
is in use. Figure 4
Figure 2 Figure 3
3.
4.
AliMed ONE™Wireless Motion Sensor
Instructions for Use, Setup, and Care

AliMed
®
Inc.
297 High St., Dedham, MA 02026 USA
PH 800.225.2610 • FAX [phone]
Manufactured for:
AliMed.com
#7721REV0919 CCO982
©2019 AliMed®Inc. All rights reserved.
Made in China
EC REP
MDSS GmbH
Schiffgraben 41
30175 Hannover,
Germany
Wall Mounting Instructions
1. Secure the bracket to the wall with the screws
provided (Fig. 3).
2. Align mounting slot on Motion Sensor with
mounted bracket.
3. Slide Motion Sensor from the left until secured
in place on the mounted bracket (Fig. 5).
3. Adjust Motion Sensor angle as needed.
Note: Once mounted to wall, Motion Sensor can
be easily removed following the same installation
instructions.
4. The Motion Sensor is now ready to use.
Figure 5
Slide Motion Sensor
from the left until
secured in place on
bracket
Environmental Conditions
Symbol Glossary
Operational Storage Transport
Temperature 10°–40°C -25°–70°C -25°–70°C
50°–104°F -13°–158°F -13°–158°F
Humidity 30%–75% 0%–95% 0%–95%
Non-condensing Non-condensing Non-condensing
Pressure 700–1060 hPa 700–1060 hPa 700-1060 hPa
Manufacturer
LOT
Batch Code/Lot Number
REF
Catalog Number/Item Number
SN
Serial Number
European Conformity Mark
Authorized representative in the
European Community
Tested/certication for compliance
to published industry standards
Consult instructions for use
Caution: Read all warnings and
precautions in instructions for use
Indicates FCC has certied device
Indicates compliance to RoHS and is free
of substances banned by RoHS
DO NOT THROW IN TRASH
Failure to comply with warning may result in injury or death. This device is not suitable for all
individuals. Other devices may be required. This device is not a substitute for visual monitoring by
caregiver. The manufacturer does not claim that this device will stop elopement and/or stop falls. This
device is designed to augment caregiver’s comprehensive resident mobility management program. This
product is to be used by a licensed caregiver only. As such, it is the entire responsibility of the caregiver
to ensure that the system is properly installed and tested. Further, the system is not designed to replace
good caregiving practices including, but not limited to:
a.) Direct patient supervision
b.) Adequate training for personnel for fall prevention and elopement
c.) Testing of the system before each use
Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and
manufacturing for a period of one year from the date of sale.
#713817 AliMed ONE Wireless Motion Sensor
#71088 9V Battery, 12/pk
Additional AliMed ONE System Components
#713815 Wireless Alarm Base
#713816 Wireless Hall Alert
#713818 Wireless Sensor Pad Transmitter (one required for each sensor pad)
#713819 30-Day Wireless Bed Sensor Pad, ea #713866, 10/pk
#713834 6-Month Wireless Bed Sensor Pad, ea #713867, 10/pk
#713838 1-Yea r Wireless Bed Sensor Pad, ea #713868, 10/pk
#713821 30-Day Wireless Chair Sensor Pad, ea #713822, 10/pk
#713836 6-Month Wireless Chair Sensor Pad, ea #713837, 10/pk
#713840 1-Yea r Wireless Chair Sensor Pad, ea #713841, 10/pk
#713823 14-Day Wireless Toilet Sensor Pad, ea
Reorder Information
Warning
Care
1. Wipe with soft, non-abrasive cloth using a 1:10 bleach solution (contains 0.5% chlorine concentration)
or follow your facility’s cleaning protocol.
2. Do not immerse in uids.
3. After cleaning, check unit is functioning properly.
CONFORMS TO AAMI STD ES60601-1, IEC STD 60601-1-6
CERTIFIED TO CSA STD C22.2 NO. 60601-1, NO. 60601-1-6