Allegro ASEK21-T-KIT User manual

8 July 2015
ASEK-21-T-KIT Page 1of 7
ASEK21-T-KIT Quick Guide
The ASEK-21-T-KIT as described below is for the purpose of programming customer
modules that contain multiple Allegro devices.
ASEK21 T-KIT Bill of Materials
•ASEK-21 Main Board(Part #: 85-0712)
•ASEK-21 Calibration Board(Part #: 85-0712-100)
•ASEK-21 Daughter Board(Part #: 85-0712-103)
•ASEK-21 Cable(Part #: 85-0712-301)
•USB A male to B male 3 foot cable (Part#: 3021001-03)
•ASEK-21 Power Supply (Part #: EMMA050400-P5P-IC)
Figure 1: Complete ASEK21 Kit

8 July 2015
ASEK-21-T-KIT Page 2of 7
Instructions for Configuring ASEK-21-T-KIT for Device Programming
1. Connect one end of the USB cable to a personal computer
2. Connect the other end of the USB cable to the USB port on the ASEK-21.
3. Connect the DSUB62 cable to ASEK-21 and the other end to J4 connector on the ASEK-21
daughterboard board (85-0712-103).
4. Connect the DC Power Supply/Cable to the 5V port on the ASEK-21.
5. Plug in the DC Power Supply to a 110V/220AC 60/50Hz outlet with the proper adapter
6. Complete setup is shown in Figure 2
Figure 2: Assembled ASEK21

8 July 2015
ASEK-21-T-KIT Page 3of 7
Daughterboard Pinout and Jumpers
It is advised to remove all 4 jumpers in the image below, and place them on one side of the pins
for safe storage. Jumpers may be necessary in very specific applications (RS232, sensor
modules without i2C pull up resistors).
ASEK21 daughterboard supports multiple communication protocols. Figure 3 below shows test
points for analog, i2c and SPI communications. Note: Analog test REQUIRES the connection of
kelvin contacts either on the daughterboard or at the sensor module.
Figure 3: ASEK21 daughterboard
Refer to Table 1through Table 4below for daughterboard pin names and brief description of
their function. Refer to Table 5for information regarding jumpers.
Pin Name
Description
Provided/Driven by
MOSI0
Master out, Slave in 0
ASEK-21
MISO0
Master in, Slave out 0
Sensor Module
SCLK0
SPI Clock 0
ASEK-21
CSN0
Chip Select 0
ASEK-21
MOSI1
Master out, Slave in 1
ASEK-21
MISO1
Master in, Slave out 1
Sensor Module
SCLK1
SPI Clock 1
ASEK-21
CSN1
Chip Select 1
ASEK-21
Table 1: SPI channels 1 and 2 on ASEK21 daughterboard

8 July 2015
ASEK-21-T-KIT Page 4of 7
Pin Name
Description
Provided/Driven by
I2CSDA0
I2C Data Channel 0
ASEK-21/Sensor Module
I2CCLK0
I2C Clock Channel 0
ASEK-21
I2CSDA1
I2C Data Channel 1
ASEK-21/Sensor Module
I2CCLK1
I2C Clock Channel 1
ASEK-21
Table 2: i2C channels 1 and 2 on ASEK21 daughterboard
Signal Description
Provided/Driven
by
VCC_F_S1 VCC Force Sensor 1 ASEK-21
VCC_S_S1
VCC Sense Sensor 1
Sensor Module
VOUT_F_S1 VOUT Force Sensor 1 ASEK-21
VOUT_S_S1 VOUT Sense Sensor 1 Sensor Module
GND_F_S1 Ground Force Sensor 1 ASEK-21
GND_S_S1
Ground Sense Sensor 1
Sensor Module
VCC_F_S2 VCC Force Sensor 2 ASEK-21
VCC_S_S2 VCC Sense Sensor 2 Sensor Module
VOUT_F_S2 VOUT Force Sensor 2 ASEK-21
VOUT_S_S2
VOUT Sense Sensor 2
Sensor Module
GND_F_S2 Ground Force Sensor 2 ASEK-21
GND_S_S2 Ground Sense Sensor 2 Sensor Module
VCC_F_S3 VCC Force Sensor 3 ASEK-21
VCC_S_S3
VCC Sense Sensor 3
Sensor Module
VOUT_F_S3 VOUT Force Sensor 3 ASEK-21
VOUT_S_S3 VOUT Sense Sensor 3 Sensor Module
GND_F_S3 Ground Force Sensor 3 ASEK-21
GND_S_S3
Ground Sense Sensor 3
Sensor Module
VCC_F_S4 VCC Force Sensor 4 ASEK-21
VCC_S_S4 VCC Sense Sensor 4 Sensor Module
VOUT_F_S4 VOUT Force Sensor 4 ASEK-21
VOUT_S_S4
VOUT Sense Sensor 4
Sensor Module
GND_F_S4 Ground Force Sensor 4 ASEK-21
GND_S_S4 Ground Sense Sensor 4 Sensor Module
Table 3: Analog Channels 1 through 4 on ASEK21 daughterboard. Note: Analog testing requires the
connection of kelvin contacts either on the daughterboard or at the sensor module.

8 July 2015
ASEK-21-T-KIT Page 5of 7
Signal Description Provided/Driven by
Dsupply *1
Digital Power Supply
Sensor Module
D+3.3 *
2
Digital +3.3V Test Point
Sensor Module
+5V
5V Test Point
ASEK-21
GPIO5
GPIO 5
ASEK-21
GPIO6
GPIO 6
ASEK-21
RS232+5V *
3
RS232 +5V
RS232
RS232GND *3
RS232 Ground
RS232
TXD
RS232 Transmit
RS232
RXD
RS232 Receive
RS232
DGND
Digital Ground
Sensor Module
DGND
Digital Ground
Sensor Module
TPGND
Scope Ground Bar
ASEK-21
Table 4: Other Pins on ASEK21 daughterboard. See notes below regarding limits
*1Dsupply
•Do not supply negative voltages
•Do not supply voltage exceeding +5.5V
•Do not apply voltage if providing digital voltage (+2.7 V, +3.3V or +5V) to module
with ASEK21
•Voltages applied to Dsupply should be in reference to DGND
*2D+3.3
•Do not supply negative voltages
•Do not supply voltages exceeding +5.5V
•Voltages applied to D+3.3 should be in reference to DGND
*3RS232+5V/GND
•Do not supply negative voltages
•Do not supply voltages outside of +3.3 to +5.5V
•Voltages applied to D+3.3 should be in reference to DGND
Jumper
Function
RS232+5
Required to enable RS232
RES232GND
Required to enable RS232
Dsupply
Will connect module Dsupply to ASEK21 Dsupply
DGND
Will connect module DGND to ASEK21 GND
Table 5: Jumpers on ASEK21 daughterboard

8 July 2015
ASEK-21-T-KIT Page 6of 7
Setting up USB Connection
Figure 4: Options for Connecting ASEK to PC
Windows will treat ASEK21 as a serial com port. The first time ASEK-21 is connected to the
computer windows will look for and install the necessary drivers. The exact port number can be
found using the device manager under “Ports.” See Table 5.
Figure 5: Screenshot from Windows device manager showing ASEK-21 as a USB Serial Port (COM3)

8 July 2015
ASEK-21-T-KIT Page 7of 7
Programming Software for ASEK-21-T-KIT
1. Register at Allegro’s software portal in order to download the ASEK21 programming
software. https://registration.allegromicro.com/login
Revision History Table
Revision
Change Description
Res.
Page(s)
Date
-
Original release
WB
All
8 July, 2015