Allen-Bradley 140MG Series User manual

DIN Mounting Adapter for 140G-G, 140G-H, 140G-I, 140G-J
Staffa per fissaggio su profilato DIN 50022
Montageclip für Befestigung auf DIN 50022 Hutschiene
Patte pour fixation sur profilé DIN 50022
Accesorio de fijación en perfil DIN 50022
Bul. 140G/140MG
DIR 1000719R0802 Version 03
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
DIR 1000719R0802 Version 03 - 140G-G-DRA, 140G-G-DRA4, 140G-H-DRA, 140G-I-DRA, 140G-I-DRA4
140G-H, 140G-J
140G-G, 140G-I 3p
140G-G, 140G-I 4p
140G-G, 140G-I
CLACK
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケスに取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件にってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
0.18"/4.6mm
from 0.75" to 0.79"
from 19 mm to 20 mm
dia. 0.13"
ø 3.5 mm
140G-H, 140G-J
x2
x2
x2
140G-H
140G-G 4p
140G-G 3p
140G-I
140G-J
A
B
C
0.18"/4.6 mm
140G-G, 140G-I
x2
Insulator
1
from 0.51" to 0.55"
from 13 mm to 14 mm
dia. 0.13"
ø 3.5 mm
LENGTH M
69 mm (2.71") M 4
LENGTH M
82 mm (3.23") M 4

DIR 1000719R0802 Version 03
(2)
2
3
1
OPTIONAL
4p
3p
BC
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut and remove
- Tagliare e rimuovere
- Durchschneiden und entfernen
- Couper et enlever
- Cortar y quitar
OPTIONAL
2
1
140G-G, 140G-I 140G-G, 140G-I
4
x2
140G-G
140G-H
140G-I
140G-J
140G-G

DIR 1000719R0802 Version 03
(3)
4p
3p
A
A
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut and remove
- Tagliare e rimuovere
- Durchschneiden und entfernen
- Couper et enlever
- Cortar y quitar
B
B
4p
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut and remove
- Tagliare e rimuovere
- Durchschneiden und entfernen
- Couper et enlever
- Cortar y quitar
4p
3p
A
A
- Cut and remove
- Tagliare e rimuovere
- Durchschneiden und entfernen
- Couper et enlever
- Cortar y quitar
- Cut and remove
- Tagliare e rimuovere
- Durchschneiden und entfernen
- Couper et enlever
- Cortar y quitar
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
- Cut
- Tagliare
- Durchschneiden
- Couper
- Cortar
5
7
6
140G-J
140G-I
140G-H

DIR 1000719R0802 Version 03
(4)
8140G-G, 140G-I
x2
140G-G
140G-G
140G-I
140G-I
1.1 Nm
9.7 lb-in
9140G-J 3p
140G-H 3p
140G-J 3p
140G-H 3p
140G-H, 140G-J 3p
x2
1.1 Nm
9.7 lb-in
LENGTH M
82 mm (3.23") M 4
LENGTH M
69 mm (2.71") M 4
LENGTH M
73 mm (2.87") M 4
LENGTH M
85 mm (3.35") M 4

DIR 1000719R0802 Version 03
(5)
11
10
1.1 Nm
9.7 lb-in
140G-J 4p
140G-J 4p
140G-H 4p
140G-H 4p
x2
140G-H, 140G-J 4p
LENGTH M
82 mm (3.23") M 4
LENGTH M
85 mm (3.35") M 4
3
1
2
1

12 DISASSEMBLY
1
2
DIR 1000719R0802 Version 03 (B0915) - B0830
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN089D-MU-P - July 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page