Allen-Bradley 2711R-APK10 User manual

Installation Instructions
Adapter Plate Kit
for PanelView 800, 7-inch and 10-inch Terminals
Catalog Numbers 2711R-APK7, 2711R-APK10
About This Publication
This document provides instructions on how to mount a PanelView 800 terminal using an adapter plate into
an existing cutout. The PanelView 800 7-inch terminal mounts to the 2711R-APK7 cutout adapter and the
10-inch terminal mounts to the 2711R-APK10 cutout adapter.
Topic Page
About This Publication 1
Package Contents 3
Tools Required 3
Disconnect the Terminal 3
Attach the Adapter Plate to the Panel 4
Attach the Terminal to the Adapter Plate 5

2Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals
Publication 2711R-IN002A-EN-P - March 2015
Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State
Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online
at http://www.rockwellautomation.com/literature/) describes some important differences
between solid-state equipment and hard-wired electromechanical devices. Because of this
difference, and also because of the wide variety of uses for solid-state equipment, all persons
responsible for applying this equipment must satisfy themselves that each intended application of
this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential
damages resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because
of the many variables and requirements associated with any particular installation, Rockwell
Automation, Inc. cannot assume responsibility or liability for actual use based on the examples
and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information,
circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of
Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety
considerations.
WARNING: Identifies information about practices or circumstances that can cause an
explosion in a hazardous environment, which may lead to personal injury or death,
property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss. Attentions help you identify
a hazard, avoid a hazard and recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment (for example,
drive or motor) to alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment (for example, drive
or motor) to alert people that surfaces may reach dangerous temperatures.
IMPORTANT Identifies information that is critical for successful application and understanding of the
product.

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 3
Publication 2711R-IN002A-EN-P - March 2015
Package Contents
The Cutout Adapter Kit includes:
• A cutout adapter plate with waterproof gasket
• #8-32 nuts with lock washers (6 sets)
• Thin mounting levers (8)
Tools Required
The following tools are required for installation:
• Socket driver with 11/32-inch socket
• Torque wrench capable of 1.36 Nm (12 in-lb) torque
Disconnect the Terminal
1. Disconnect power at the source and remove the power cord from the PanelView terminal.
2. Disconnect all communication cables from the terminal.
Remove the Existing Terminal
1. Remove the self-locking levers that secure the terminal to the panel.
2. Slide the existing terminal out from the panel.
IMPORTANT
Thin mounting levers are only included with 2711R-APK7 and are for use with 2711R-T7T.
There are no mounting levers included with 2711R-APK10. Use the regular mounting levers
that come with 2711R-T10T.
ATTENTION: Make sure the power cord and all communication cables have been
disconnected from the PanelView terminal.
Regular mounting leverThin mounting lever

4Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals
Publication 2711R-IN002A-EN-P - March 2015
Attach the Adapter Plate to the Panel
1. Align the studs on the cutout adapter plate with the existing stud holes on the front of the panel.
2. Place the adapter plate into the front of the panel cutout until the sealing gasket material is firmly
pressed against the front of the panel.
3. Using the supplied nuts with lock washers, fasten the cutout plate onto the studs until the sealing
gasket is slightly compressed against the front of the panel.
4. Using the torque wrench, tighten the nuts to not more than 1.36 Nm (12 in-lb) to maintain a
NEMA Type 4X, 12, or 13 rating. Do not overtighten.
Rear of panel or enclosure
Front of panel or enclosure
Nut
M3.5 H3.0
Screw
M3.5 L15 with Nyseal (waterproof)
Front of adapter plate
with waterproof gasket

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 5
Publication 2711R-IN002A-EN-P - March 2015
Attach the Terminal to the Adapter Plate
1. Insert the new terminal into the front of the enclosure until the terminal gasket is flush with the
adapter plate.
Rear of panel or enclosure
Nut
M3.5 H3.0
Rear of PanelView 800 terminal
(7-inch terminal shown)
Mounting levers

6Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals
Publication 2711R-IN002A-EN-P - March 2015
2. Insert all mounting levers into the mounting slots of the terminal.
Slide each lever until the flat side of the lever touches the surface of the panel.
3. When all levers are in place, slide each lever an additional notch or two until you hear a click.
4. Rotate each lever in the direction indicated until lever is in the final latch position. Follow the
latching sequence below to obtain the optimum terminal fit.
IMPORTANT
Use thin mounting levers only when using the 2711R-T7T terminal with the adapter plate.
Short, flat side of mounting lever
Mounting levers
Mounting slots
Rotate until notch in lever aligns with
proper alignment mark on terminal. Notch
Six alignment marks
Latching sequence for 2711R-T7T Latching sequence for 2711R-T10T
14
32
56
14
32
57
86

Adapter Plate Kit for PanelView 800, 7-inch and 10-inch Terminals 7
Publication 2711R-IN002A-EN-P - March 2015
5. Use this table as a guide to insure an adequate gasket seal between the terminal and the panel.
Terminal Markings for
Alignment
Lever
Position Panel Thickness Range Typical
Gauge
1 1.52…2.01 mm (0.060…0.079 in.) 16
2 2.03…2.64 mm (0.08…0.104 in.) 14
3 2.67…3.15 mm (0.105…0.124 in.) 12
4 3.17…3.66 mm (0.125…0.144 in.) 10
5 3.68…4.16 mm (0.145…0.164 in.) 8/9
6 4.19…4.75 mm (0.165…0.187 in.) 7
ATTENTION: Follow the instructions above to obtain a proper seal and to prevent potential
damage to the terminal. Rockwell Automation assumes no responsibility for water or
chemical damage to the terminal or other equipment within the enclosure because of
improper installation.
6
1
1
2
3
4
5
6
44881

Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products.
At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge
base of FAQs, technical and application notes, sample code and links to software service packs, and
a MySupport feature that you can customize to make the best use of these tools.
For an additional level of technical phone support for installation, configuration and troubleshooting,
we offer TechConnect support programs. For more information, contact your local distributor or
Rockwell Automation representative, or visit http://www.rockwellautomation.com/support/.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information
that's contained in this manual. You can also contact a special Customer Support number for initial
help in getting your product up and running.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when shipped
from the manufacturing facility. However, if your product is not functioning and needs to be returned,
follow these procedures.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on
how to improve this document, complete this form, publication RA-DU002, available at
http://www.rockwellautomation.com/literature/.
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
United States or Canada 1.440.646.3434
Outside United States or Canada Use the Worldwide Locator at
http://www.rockwellautomation.com/support/americas/phone_en.html, or
contact your local Rockwell Automation representative.
United States Contact your distributor. You must provide a Customer Support case number (call the phone
number above to obtain one) to your distributor to complete the return process.
Outside United States Please contact your local Rockwell Automation representative for the return procedure.
Samara
tel. [phone]
[email protected]
Yekaterinburg
tel. [phone]
yekat[email protected]
St. Petersburg
tel. [phone]
[email protected]
Moscow
tel. [phone]
[email protected]
Helsinki
tel. [phone]
[e-mail]
Vilnius
tel. [phone]
[email protected]
Riga
tel. [phone]
[email protected]
Мinsk
tel. [phone]
[email protected]
Tallinn
tel. [phone]
[email protected]
Кiev
tel. [phone]
[email protected].ua