Allen-Bradley 140G Series User manual

Battery Unit 140G-ELBU for electronic trip units
Unità di alimentazione 140-ELBU per relè elettronici
Versorgungseinheit 140-ELBU für elektronischen Auslöser
Unidad de alimentación 140-ELBU para relè electrónicos
Unité de alimentation 140-ELBU puor déclencheur électroniques
Bul. 140G
DIR 1000631R0001 Version 02
WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
1Performance 2Battery Check
DIR 1000631R0001 Version 02 - LSIG, LSIG-MM (140G-N, 140G-NS, 140G-R)
The trip unit for this MCCB is self powered when the main
power has been applied to the circuit braker. The battery unit is
used for self test/diagnostics when the circuit breaker has
been OFF or Tripper for extended periods of time.
Note:
For use with N/NS/R frame Circuit breakers
with LSIG, LSIG-MM Trip Units.
Led “ON”
Button -
Battery Check
With unit not connected to trip unit, press the button: LED “ON”
turned ON indicates battery charged.
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
ALKALINE

3Connection examples
LSIG:
LSIG-MM:
DIR 1000631R0001 Version 02 (L6826) - B0934
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN151C-MU-P - May 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
LSIG PR331/P
LSIG-MM PR332/P
Use the mechanical adapter to properly align the battery unit with the trip unit. Refer to the figures above.
4Battery replacement
This product contains an alkaline battery which is intended to be replaced during the life of the product.
At the end of its life, the battery should be collected separately from any unsorted municipal waste.