Allen Sports S555 User manual

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rack on any
vehicle on which it can not be properly mounted as described in this instruction sheet.
• Rack should only be used on vehicles with Class III or IV 2” receiver hitches.
• NEVER use on trailer or front of vehicles.
• Bikes must be tied to rack using tie-downs, or additional straps if necessary.
• Check periodically during use taht all bolts and pins are tight, and that rack and bicycles are secure.
• Never carry more than 5 bicycles (MAX CAPACITY: 175 LB) - no tandems, mopeds, or recumbents. Car tail lights
must remain visible. Bikes must be securely tied to rack. Use bike tie-downs, or additional straps if necessary.
• Drive conservatively, especially over bumps. Never use off-road.
• Do not use if any part of the rack is damaged, worn, or missing. Contact R. A. Allen Co., Inc. for replacement parts..
CAUTION: Use Allen S-555 only in accordance with local motor
vehicle and traffic regulations.
• Install rack and load bicycles only at a safe distance away from
moving traffic.
• Make sure that all of rack and bicycles are kept at a safe distance
from road and hot exhaust.
• Only operate vehicle with rack in an upright, locked position.
• Bicycles should never extend beyond sides of vehicle.
• Remove rack from car, or fold carry arms down when not in use.
• INSERT LOWER PORTION OF RR POST INTO
HITCH INSERT SO THAT THE HOLES AT THE
BOTTOM OF EACH PART LINE UP.
• INSERT THE 3/8” X 3” BOLT THROUGH THE HOLE,
AND THREAD 1—3/8” LOCK NUT ONTO THE END
OF THE BOLT.
• PIVOT THE RR POST INTO THE UPRIGHT
POSITION, SO THAT THE SECURING LATCH
SNAPS INTO PLACE.
• TIGHTEN NUT AND BOLT FIRMLY USING TWO
WRENCHES.
• INSERT CARRY ARM ASSEMBLY
INTO UPPER PORTION OF RR
POST, LINING UP THE HOLES IN
EACH PART.
•INSERT THE 3/8” X 2 1/2” BOLTS
THROUGH EACH HOLE, AND
THREAD 1—3/8” LOCK NUT ONTO
THE END OF THE BOLTS.
• TIGHTEN EACH NUT AND BOLT
FIRMLY USING TWO WRENCHES.
NOTE: UPON COMPLETION, BOTH
PARTS SHOULD BE FIRMLY
JOINED TOGETHER.
.
IMPORTANT:
WHEN RACK IS IN AN
UPRIGHT POSITION,
SECURING LATCH MUST
BE FULLY ENGAGED FOR
RACK TO FUNCTION
PROPERLY.
CARRY ARM ASSEMBLY
TOOLS REQUIRED: 2—9/16” WRENCH & 2—3/4” WRENCH;
or 2 ADJUSTABLE WRENCHES
PARTS
HITCH INSERT
S-555 BOX SHOULD CONTAIN THE
FOLLOWING ITEMS:
1- CARRY ARM ASSEMBLY 1-
1—HARDWARE KIT,
CONTAINING:
2 - 3/8” X 2 1/2“ BOLT
1 - 3/8” X 3” BOLT
4 - 3/8” LOCK NUT
1 - 1/2” LOCK NUT
1 - 1/2” WOBBLE BOLT
1 - 70” BOTTOM STRAP
RR POST
1- 1- SPINE SHIELD
A. ASSEMBLING RACK: B.
STEP 1 STEP 2
STEP 3
3/8”
LOCK
NUT
3/8”x 2 1/2”
BOLT
RR POST
HITCH INSERT
3/8” X 3”
BOLT
SECURING LATCH
3/8”
LOCK NUT
INSTALLING SPINE PAD
WITH “ALLEN SPORTS” IN THE UPPER
POSITION, LINE UP THE RECESSES
FOR THE NUT AND BOLT HEADS, AND
SNAP THE SPINE PAD INTO PLACE
ONTO THE RECEIVER RACK’S
VERTICAL POST.
MODEL S555
INSTRUCTIONS
ENGLISH - PAGE 1
PRODUCT REGISTRATION:
MAKE SURE TO REGISTER YOUR PURCHASE AT
http://allensportsusa.com/about/product-registration
TO QUALIFY FOR PRODUCT WARRANTY AND TO
RECEIVE IMPORTANT PRODUCT NOTIFICATIONS

INSTALLING RACK ONTO VEHICLE:
• WITH ARMS IN FOLDED
POSITION, INSERT RACK
INTO RECEIVER HITCH. LINE
UP HOLE IN THE BASE WITH
HOLE OF RECEIVER HITCH.
• INSERT NO-WOBBLE BOLT
INTO HOLE, MAKING
SURE THAT THE SHOULDER
OF THE BOLT COMES AGAINST
RECEIVER RACK INSIDE OF
HITCH.
• TIGHTEN FIRMLY USING TWO
- 3/4” WRENCHES. THERE
SHOULD NOT BE ANY
MOVEMENT OF THE RACK
INSIDE OF THE HITCH WHEN
C.
D.
LOADING BICYCLES ON RACK:
E.
MODEL S-555 SHOULD ONLY BE USED ON 2” RECEIVER HITCHES
INSTALLED ON AUTOMOBILES. NEVER USE THIS RACK ON A TRAILER.
FOLDING UP CARRY ARMS:
• REMOVE ALL LOOSE ITEMS FROM BICYCLES (PUMPS, BAGS, ETC.), AND CHECK THAT ALL QUICK RELEASE HUBS ARE TIGHT.
• LOAD FIRST BICYCLE WITH ITS CHAIN AND GEARS FACING AWAY FROM RACK. MAKE SURE THAT BICYCLES DO NOT COME IN
CONTACT WITH VEHICLE.
• LOAD SUBSEQUENT BICYCLES IN ALTERNATING DIRECTIONS. FOR BEST WEIGHT DISTRIBUTION, LOAD HEAVIEST BICYCLES
FIRST, WITH LIGHTER BICYCLES ON THE OUTSIDE. ADD PADDING BETWEEN BICYCLE CONTACT POINTS, IF NECESSARY.
• AFTER BICYCLES ARE LOADED, CHECK THAT ENTIRE RACK IS SECURE AND THAT NO-WOBBLE BOLT IS TIGHT, AND THAT THE
RACK IS STILL FIRMLY IN PLACE. VISION OUT OF REAR WINDOW MAY BE RESTRICTED—USE SIDE MIRRORS ACCORDINGLY
WHEN BACKING UP.
SPECIAL NOTE ON INSTALLING WOMEN’S STYLE FRAMES:
PLACE ONE CARRY ARM UNDER FRONT TOP TUBE. WITH THE OTHER CARRY ARM, ROTATE TIE-DOWN CRADLE, AND
PLACE CARRY IN SPACE BEHIND SEAT TUBE AND BELOW REAR DOWN-STAY. THE ALLEN 900B ADAPTOR BAR IS ALSO
RECOMMENDED FOR THIS APPLICATION.
SECURING BIKES TO RACK:
F. ALL BIKES MUST BE SECURELY TIED TO RACK. USE INDIVIDUAL TIE-DOWN STRAPS, OR
ADDITIONAL STRAPS IF NECESSARY.
3. USE 70” STRAP TO PULL
ALL BICYCLES TOGETHER
AROUND BOTTOM BRACK-
ETS. STRAP SHOULD ALSO
SECURE WHEELS.
1.PLACE BICYCLE IN CRADLE. 2. LOCK DOWN TIE-DOWN STRAP.
• TO FOLD UP CARRY ARMS,
SQUEEZE TOGETHER THE TWO RED
TABS ON THE BACK OF THE CARRY
ARM ASSEMBLY, AND SWING
CARRY ARMS INTO UPRIGHT
POSITION.
• THE PINS CONNECTED TO THESE
TABS SHOULD “SNAP” INTO PLACE
TO HOLD THE CARRY ARMS IN AN
UPRIGHT POSITION.
• REVERSING THIS PROCESS WILL
KEEP THE CARRY ARMS LOCKED IN
A DOWN POSITION.
• IF BOTH PINS ON YOUR RACK DO
NOT PROPERLY ENGAGE THE
CARRY ARMS IN THE UPRIGHT
POSITION, DO NOT USE YOUR
RACK, AND CONTACT R. A. ALLEN
CO..
.
1. SQUEEZE
RED TABS
2.
ROTATE ARMS INTO
UPRIGHT POSITION
LOCK NUT
NO-WOBBLE BOLT
ALLEN LIFETIME WARRANTY:
IF AN ALLEN BIKE RACK IS FOUND TO HAVE A DEFECT IN
WORKMANSHIP OR MATERIAL OVER THE LIFETIME OF THE
ORIGINAL PURCHASER, ALLEN WILL REPAIR OR REPLACE
THE RACK FREE OF CHARGE. THE WARRANTY DOES NOT
COVER DAMAGE OR WEAR WHICH OCCURS AS A RESULT OF
DAY TO DAY USE OR GENERAL WEAR AND TEAR.
Get the lastest news, info,
give-a-ways and pics on
our social media sites! @AllenSportsUSA
@AllenSportsUSA
/AllenSportsUSA
R. A. ALLEN CO., INC.—ALLEN SPORTS USA 60
THOREAU ST. - #161
CONCORD, MA 01742, USA
[email protected]
WWW.ALLENSPORTSUSA.COM
©2015 R. A. ALLEN CO., INC., ALL RIGHTS RESERVED V.3.15
For More
Product Info &
List of Dealers
Scan Our QR Code
MODEL S555
INSTRUCTIONS
ENGLISH - PAGE 2