TruXedo Lo Pro QT User manual

 It is the responsibility of the owner/user to read this manual and comply
with the operating procedures. The owner/user is also responsible for
inspecting the TruXedo® cover, and for having parts repaired or replaced
when worn or damaged.
Failure to follow safety instructions and warning labels could result in
failure of your cover system and/or personal injury.
• Always wear safety glasses and/or other necessary protective
equipment when installing your TruXedo®.
• These instructions are complete for most pickup models. Additional
instructions are included, if required for your truck. Please read entire
manual before installing your TruXedo®.
Vinyl cover can be hand washed with mild soap and water or cleaned in
a car wash. Thoroughly rinse cover to remove any soap residue. Cover
can be treated with any vinyl protectant made for tonneau covers. 




 

  
 
 
 
 

 
 
 
Premium Soft roll-uP tonneau Cover


TruXedo warrants that all new, unused products are free from defects
in material and workmanship. This Warranty is effective if the product
is properly installed and used for the purpose intended for the life of the
product. It applies to the original buyer only. TruXedo’s obligation under
this Warranty is limited to repairing, or at its option, replacing any part that is
returned, transportation prepaid, to TruXedo, Yankton, South Dakota, if the
product is, in our judgment, defective. All materials must be accompanied
by an RMA (Returned Material Authorization) number requested by and
authorized in advance of returning the materials. TruXedo shall not be
liable or responsible to supply or pay labor to replace any part found
defective, nor shall it be liable for any damages of any kind or nature to
person, product, or property.

Inside Bulkhead
side rail
header seal on
top of bulkhead
approx 8”

Passenger’s
Side Rail
Header Guide
Bracket
Spring Plunger Safety Straps
 Attach the TruXedo rails to the truck’s vertical inside ange as
shown in Detail A. To get the correct TruXedo rail alignment
from front to back, See Detail-B. Compress the rear D-seal
against the closed tailgate and hold. Attach clamps starting at
the tailgate. Evenly space 3 clamps along each TruXedo rail,
leaving approximately 8” on each end.
 For optimum latching performance and cover t, side rails
must be level. To adjust rails, loosen screws and reposition
male clamps higher or lower. Tighten all clamps.
 Push header guides into place under side rail. A  sound
will indicate a secure attachment. See detail D & E below.
 Set cover assembly behind cab with header seal on top of of
bulkhead. See detail C.

Driver’s
Side Rail
Cover
Assembly
Rubber
Seal
End
Plug

truck’s vertical
inside flange










cover assembly
truck box front
side rail



!
clamp
assembly
 
 
 Note:Clamp congurations shown are for reference only and
are not intended to be standard for all pickups.
detail-a
height
flush
see step 2 for correct
clamp height.
detail-b
3/16” compress
d-seal
closed tailgate


Header Guide
Caution
Cover Must Be Secured On Both Sides
This cover system is equipped with header guide slides on both sides of the vehicle. Both slides
MUST BE ENGAGED UNDER THE SIDE RAILS before operating the vehicle. Failure to do so could
cause accidental release of the cover, resulting in personal injury or property damage.
P/N 1704607 Rev. A
Push
Click
(Passenger Side Shown)
Notice
DetAiL “c”
DetAiL “e”
DetAiL “D”
Header Guide Retainer

pull cover over rails
toggle
press edges
 To release cover, Trigger pull rear release toggle. Start rolling
cover toward cab making sure both sides of cover roll evenly. For
best results leave unrolled portion of cover attached to the hook
fastener and Velcro® loop fasteners while opening.
 Set tension during With cover closed, release hook and loop fastener from both side rails near cab. Check
compression of both spring plungers against the front header per diagram. Roll cover open and make adjustments. Close cover and
re-check adjustment. Repeat until satisfactory tension has been achieved.
header
cover
toggle
header seal
header stop
adjust
with
at screwdriver

cover secured
open
safety
straps
side rail
front header
spring plunger




• Spring plunger compensates for material expansion &
contraction caused by temperature changes.
• Check cover tension after installation, seasonally, and after
extreme temperature changes.
• For best performance, adjust tension regularly to protect
your cover against wind wear.

lock toggle into header
header seal
inside tailgate
spring plunger
front header
Note:Adjust tension in small increments.
Slight adjustments will gain signicant results.

Check side rails to make sure they are level. See Step 2.
Make sure the header seal is not caught between side rail & header.
Check position of side rails on pickup box, they may be positioned too low. See Step 1.
Make sure cover has proper tension. See Step 9.
 See Step 9 to adjust tension.
* VELCRO® is a registered trademark of the Velcro companies.


Call our friendly customer service staff
at TruXedo Toll Free:

Mon - Fri 8 am - 5 pm CST
 
Unroll cover toward tailgate and rest bows on side rails.
Rotate header into header stops and press down to lock
toggle into header.
 



 Secure hook fastener and Velcro® loop fastener strips on
one side of rail, by pressing along full length of rail. Pull
cover tight across pickup bed, and secure fasteners on
opposite side rail.
Note: Secure hook fastener and Velcro®
loop fastener along entire length
of both side rails before driving
vehicle. This will prevent wind lifting
the cover and causing damage.
Note: If tailgate has a key lock, TruXedo® is secured until tailgate
is unlocked and opened.
hook and loop
fastener






no less than 1/16”
  push up on
retainer tab with thumb and pull header guide over retainer
until it stops. Do this for both passenger and driver side. Then
lift cover assembly off of side rails.
Push Up To
Release
Move Header Guide To
Disengage.


Header Guide
Retainer Tab


 1115353 Header Safety Strap
 1703344 Blind Rivet, 1/8” x 3/16”
 1701595 End Plug, 1” OD
 ___*___ Black Bow
 1702992 Spring Plunger, 5/8” x 2.15”
 1703260 Tension Control Bracket
1115354 Header Insert Safety Clip
 ___*___ Hook and Loop Fasteners
 1703332 Hitch Pin, 1/16” x 1 5/16”
 1115191 Aluminum Clamp Assy
 ___*___ Side Rail, Passenger’s Side
 ___*___ Side Rail, Driver’s Side
 1114773 Flat Spring, 5/8” x 3 7/8”
 1704213 Latch Assembled
25 1702926 Cap Screw, 5/16” x 7/8”
 1704187 Header Stop
 1115373 Side Rail End Plugs w/Seal (Set of Two)
 1704383 Filister Head Screw
 1117467 Rear Header 08 End Plugs (Set of Two)
 ___*___ Black Rear Header
1704194 Weld Nut 5/16-18 ZP
* Please specify length or make and model of vehicle.
 ___*___ TruXedo® Lo Pro QT Replacement Cover
 ___*___ Black Front Header
 ___*___ Header Seal, Notched
 1117540 Front Header 08 End Plugs (Set of Two)
 1117592 Header Guide, Driver’s Side
 1117593 Header Guide, Passenger’s Side
 ___*___ Safety Strap
 1700428 Washer Flat 5/16”
 1704606 Cap Screw, 5/16-18 x 5/8”
 1117591 Header Guide Retainer.



2
3
6
4
31
7
10
11
9
2
14
16
15 27
20
21
18
19
12
17
1
5
13
3
26
27 24
23
22
25

28
29
30
8
TONNEAU COVERS CAR ACCESSORIES