Allnet ALL0234Nano User manual

User´s Manual
ALL0234Nano
USB Wireless N 150Mbit Adapter

ALLNET GmbH 2011 ALL0234Nano
1
Network Card Installation
Please follow the following steps to install your new wireless network card:
1. Insert the ALL0234Nano into an empty USB2.0 port of your computer when computer has power on.
Never use force to insert the stick, if you feel it’s stuck, flip the stick over and try again.
2. Insert device driver CD into the CDROM drive of your computer, double click the ‘Setup.exe’ icon and
run the ‘Setup.exe’ program.
3. Then pop up the installshield Wizard.
4. Click ‘Next’.

ALLNET GmbH 2011 ALL0234Nano
2
5. Please wait while the installation procedure is running. Finally, click ‘Finish’ and restart your
computer to finish the driver installation.

ALLNET GmbH 2011 ALL0234Nano
3
Connect to Wireless Access Point
1. After installation has finished, wireless configuration utility will be shown on the desktop of your
computer, and it will try to connect to any unencrypted wireless access point automatically. If you
want to connect to a specific wireless access point, or the access point you wish to connect uses
encryption, you have to configure the wireless network card and input the correct password to get
connected to the wireless access point. Double click the icon on your desktop.
2. Scan available wireless access point. Scan results will display in the ‘Available Network’ zone. If you
can’t find the access point you wish to connect here, click the ‘Refresh’ button, until you can find your
wireless access point..
3. Choose the wireless access point’s SSID, and click ‘Add to Profile’.

ALLNET GmbH 2011 ALL0234Nano
4
4. If it’s an open wireless network system, you will be warned by this pop up dialogue .
5. Click ‘OK’, and fill your information in the ‘Wireless network properties’, or just click ‘OK’. If the
wireless access point has enabled encryption, you will have to input the WEP key or WPA preshared
key in the form.

ALLNET GmbH 2011 ALL0234Nano
5
6. Then, you can find your wireless access point in the ‘Profile’, it will automatically connect to the
access point every time you use your usb network card.
7. After you have connected to the wireless access point successfully, click the ‘General’ menu, you
can get the detail information of connected access point, such as status、IP address、speed and so on.

ALLNET GmbH 2011 ALL0234Nano
6
8．Click the ‘Wi-Fi Protect Setup’ menu, by a simple setting allows you to secure connection to your
wireless AP.
9．This wireless network card with a WPS button, you can easily connect to a wireless router and
achieve encryption; press this button, the computer screen appears around the vicinity of the AP signal
search interface.

ALLNET GmbH 2011 ALL0234Nano
7
10．At this point just press the WPS button wireless router; wait a while to realize the connection and
encryption.
11．Click on the available network we can see that encryption is WPA-WPA2-PSK/TKIP-AES. You have
established a good secure wireless network.

ALLNET GmbH 2011 ALL0234Nano
8

ALLNET GmbH 2011 ALL0234Nano
9
CE-Declaration of Conformity
For the following equipment:
Germering, December 08, 2011
USB Wireless N 150Mbit Adapter
ALL0234Nano
The safety advice in the documentation accompanying the products shall be
obeyed. The conformity to the above directive is indicated by the CE sign on the
device.
The Allnet ALL0234Nano conforms to the Council Directives of 1999/5/EC.
This equipment meets the following conformance standards:
EN60950-1:2006/A11:2009
EN62311:2008
EN301489-1 V1.8.1:2008-04
EN301489-17 V2.1.1:2009-05
EN300328 V1.7.1:2008-10
This equipment is intended to be operated in all countries.
This declaration is made by
ALLNET Computersysteme GmbH
Maistraße 2
82110 Germering
Germany
Germering, 08.12.2011