2
SAFETY PRECAUTIONS
- Hands-free monitor.
- 4.3”TFT colour screen.
- Monitor with simple installation (non-polarised 2 wire BUS).
- Capacitive buttons to access and select menu functions.
- .User menu
- Installer setup.
- Screen and volume settings menu.
- Start/stop communication button.
- Door release push button.
- .Status LEDs
- Dip switches for setting the monitor address (call code).
-Always disconnect the power supply before installing or making modifications to the device.
- installationThe and handling of these devices must be carried out by authorised personnel.
- The wiring must run at least 40 cm away from any other wiring.
- Do not overtighten the screws on the terminal block.
- I and place without projectionsnstall the monitor in a dry protected risk of drip or water .
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the system to the mains, check the connections between the door panel,
power supply, distributors and monitors.
- Always follow the instructions contained in this manual.
CHARACTERISTICS
SYSTEM OPERATION
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that
the call is being made and LED will turn on. If vocal synthesis is activated then a “call inis
progress”message will indicate a call is being made. At this moment the apartment's monitor(s)
receives the call. During the call the visitor can correct his call by pressing a push button
corresponding to a different apartment, in which case the original call is cancelled.
- The ring tone lasts for 40 seconds. Without alerting the visitor, their image appears on the master
monitor . : the image appears on the monitor (with code 0to receive the call For Villakit application
“apartment 1”or monitor with code 16 if the call is in “apartment 2”) when receiving the call
without the visitor being alerted.
If the call is not answered within 40 seconds, LED will turn off and the channel will be freed.
- To establish communication, press button on any monitor in the apartment. Door panel LED
will turn on. If the vocal synthesis is enabled the message "you can speak now" will be heard
confirming the communication is activated.
- Communication will last for one and a half minutes or until button is pressed again. When
communication has finished, LEDs and will turn off and the channel will be freed. If vocal
synthesis is activated, a “Communication is finished”message will indicate that the call is over.
- To open the door, press button during the call or communication processes: one press will
activate the lock release for five seconds and LED will also turn on for five seconds. If vocal
synthesis is activated, a “Door pen”message will be indicated on the door panel.is o
- The descriptions of the function push buttons are found on page 3.
*
( )
( )* For more information, see the “TVESTA2 GB2 User Manual".
http://interco.ms/awd211
3
MONITOR DESCRIPTION
Monitor address (code) setup:
*
( )
VESTA2
CODE 0
APARTMENT 1
VESTA2
CODE 0 CODE 16
APARTMENT 1
1-apartment kit 2-apartment kits
( )* For more information, see the “TVESTA2 GB2 User Manual"
http://interco.ms/awd211
MONITOR INSTALLATION
1.60m
x4 30
Screws supplied with the
embedding box.
Surface Embedding boxLocation
*
( )
*
( )
Building
1 2 3
ON
E : 0 +0 +4+0+16 = 20xample
Switch number: 1 2 3 4 5
valueON : 1 2 4 8 16
Value chart DIP
4 5 6
Dip6: Sets the end of line. Set to ON in monitors where the video cable
terminates. Remainder set to OFF.
Dip1 Dip5:to .Set the monitor address (addresses 0 to 31)
Switches set to OFF have a value of zero.
The values of the switches set to ON are shown in the enclosed chart.
The monitor code will be the sum of the values of the switches set to ON.
VESTA2
APARTMENT 2
2-apartment kit: Monitor code 16 is the last,s
dip 6 of the end of line to ON.
1
( )
1
( )
VESTA2 G 2 MONITORB VESTA2 G 2 MONITORB
a. .Microphone
b. 4.3”TFT colour screen.
c. Close push button.
d. Menu push buttons.
e. “Do not disturb”push button/indicator.
f. Start/stop communication .function push button
During standby: Display door panel image.
g. releaseDoor function push button.
During standby: Press for 10 seconds to
activate/deactivate the “doctor mode”function
(function code [9018] must be activated).
h. Attachment holes.
i. Horizontal cable input.
j. Con ector.n
k. BUS connection terminals.
l. Con!guration DIP switch.
Menu access and function selection push button.
Menu back push button.
Menu push buttons and status LEDs:
Menu scroll down push button.
Menu scroll up push button.
Power supply .status LED
Push button: End call/communication.
During standby: Enter/exit menu mode.
“Do not disturb”function access push button.
LED on: “do not disturb”mode activated.
LED blinking: “doctor mode”activated.
LED off: function not activated.
1 2 3
ON DIP
4 5 6
l
h
j
i
k
b
c
f
d
g
a
e
