Philips 86BDL4152T User manual

www.philips.com/welcome
86BDL4152T
V1.00
User Manual (English)

86BDL4152T
ii
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specied in this documentation may result in exposure to
shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keepthedisplayoutofdirectsunlightandawayfromstovesoranyotherheatsources.
• Removeanyobjectthatcouldfallintoventilationholesorpreventpropercoolingofthedisplay’selectronics.
• Donotblocktheventilationholesonthecabinet.
• Whenpositioningthedisplay,makesurethepowerplugandoutletareeasilyaccessible.
• Whenturningoffthedisplaybydetachingthepowercord,wait6secondsbeforere-attachingthepowercordfornormaloperation.
• EnsuretheuseofanapprovedpowercordprovidedbyPhilipsatalltimes.Ifyourpowercordismissing,pleasecontactyourlocalservicecenter.
• Donotsubjectthedisplaytoseverevibrationorhighimpactconditionsduringoperation.
• Donotknockordropthedisplayduringoperationortransportation.
• Theeyeboltisforusageinshort-timemaintenanceandinstallation.Wesuggestnottousetheeyeboltformorethan1hour.Prolongusageis
prohibited.Pleasekeepaclearsafetyareaunderthedisplaywhileusingtheeyebolt.
Maintenance:
• Toprotectyourdisplayfrompossibledamage,donotputexcessivepressureontheLCDpanel.Whenmovingyourdisplay,grasptheframetolift;do
notliftthedisplaybyplacingyourhandorngersontheLCDpanel.
• Unplugthedisplayifyouarenotgoingtouseitforanextensiveperiodoftime.
• Unplugthedisplayifyouneedtocleanitwithaslightlydampcloth.Thescreenmaybewipedwithadryclothwhenthepowerisoff.However,never
useorganicsolvent,suchas,alcohol,orammonia-basedliquidstocleanyourdisplay.
• Toavoidtheriskofshockorpermanentdamagetotheset,donotexposethedisplaytodust,rain,wateroranexcessivelymoistenvironment.
• Ifyourdisplaybecomeswet,wipeitwithdryclothassoonaspossible.
• Ifaforeignsubstanceorwatergetsinyourdisplay,turnthepoweroffimmediatelyanddisconnectthepowercord.Thenremovetheforeignsubstance
orwater,andsendtheunittothemaintenancecenter.
• Donotstoreorusethedisplayinlocationsexposedtoheat,directsunlightorextremecold.
• Inordertomaintainthebestperformanceofyourdisplayandensurealongerlifetime,westronglyrecommendusingthedisplayinalocationthatfalls
withinthefollowingtemperatureandhumidityranges.
-Temperature:0-40°C32-104°F
-Humidity:20-80%RH
• LCDpaneltemperatureneedtobe25degreesCelsiusatalltimeforbetterluminanceperformance.
IMPORTANT:Alwaysactivateamovingscreensaverprogramwhenyouleaveyourdisplayunattended.Alwaysactivateaperiodicscreenrefresh
applicationiftheunitwilldisplayunchangingstaticcontent.Uninterrupteddisplayofstillorstaticimagesoveranextendedperiodmaycause“burnin”,
alsoknownas“after-imaging”or“ghostimaging”,onyourscreen.Thisisawell-knownphenomenoninLCDpaneltechnology.Inmostcases,the“burned
in”or“after-imaging”or“ghostimaging”willdisappeargraduallyoveraperiodoftimeafterthepowerhasbeenswitchedoff.
WARNING:Severe“burn-in”or“after-image”or“ghostimage”symptomswillnotdisappearandcannotberepaired.Thisisalsonotcoveredunderthe
termsofyourwarranty.
Service:
• Thecasingcovershouldbeopenedonlybyqualiedservicepersonnel.
• Ifthereisanyneedforrepairorintegration,pleasecontactyourlocalservicecenter.
• Donotleaveyourdisplayunderdirectsunlight.
Ifyourdisplaydoesnotoperatenormally,havingfollowedtheinstructionssetoutinthisdocument,pleasecontactatechnicianoryour
localservicecenter.

86BDL4152T
iii
Read and follow these instructions when connecting and using your display:
• Unplugthedisplayifyouarenotgoingtouseitforanextensiveperiodoftime.
• Unplugthedisplayifyouneedtocleanitwithaslightlydampcloth.Thescreenmanybewipedwithadryclothwhenthepoweris
off.However,neverusealcohol,solventsorammonia-basedliquids.
• Consultaservicetechnicianifthedisplaydoesnotoperatenormallywhenyouhavefollowedtheinstructionsinthismanual.
• Thecasingcovershouldbeopenedonlybyqualiedservicepersonnel.
• Keepthedisplayoutofdirectsunlightandawayfromstovesoranyotherheatsources.
• Removeanyobjectthatcouldfallintotheventsorpreventpropercoolingofthedisplay’selectronics.
• Donotblocktheventilationholesonthecabinet.
• Keepthedisplaydry.Toavoidelectricshock,donotexposeittorainorexcessivemoisture.
• WhenturningoffthedisplaybydetachingthepowercableorDCpowercord,waitfor6secondsbeforere-attachingthepower
cableorDCpowercordfornormaloperation..
• Toavoidtheriskofshockorpermanentdamagetothesetdonotexposethedisplaytorainorexcessivemoisture.
• Whenpositioningthedisplay,makesurethepowerplugandoutletareeasilyaccessible.
• IMPORTANT:Alwaysactivateascreensaverprogramduringyourapplication.Ifastillimageinhighcontrastremainsonthe
screenforanextendedperiodoftime,itmayleavean‘after-image’or‘ghostimage’onthefrontofthescreen.Thisisawell-known
phenomenonthatiscausedbytheshortcomingsinherentinLCDtechnology.Inmostcasestheafterimagewilldisappeargradually
overaperiodoftimeafterthepowerhasbeenswitchedoff.Beawarethattheafter-imagesymptomcannotberepairedandisnot
coveredunderwarranty.
EU Declaration of Conformity
ThisdevicecomplieswiththerequirementssetoutintheCouncilDirectiveontheApproximationoftheLawsoftheMemberStatesrelatingto
ElectromagneticCompatibility(2014/30/EU),Low-voltageDirective(2014/35/EU),RoHSdirective(2011/65/EU),andRadioEquipmentDirective(2014/53/
EU).
ThisproducthasbeentestedandfoundtocomplywiththeharmonizedstandardsforInformationTechnologyEquipment,theseharmonizedstandards
publishedunderDirectivesofOfcialJournaloftheEuropeanUnion.
ESD Warnings
Whenuserclosetothemonitormaycausetheequipmentdischargeandreboottothedisplayofmainmenu.
Warning:
ThisequipmentiscompliantwithClassAofEN55032/CISPR32.Inaresidentialenvironmentthisequipmentmaycauseradiointerference.
Federal Communications Commission (FCC) Notice (U.S. Only)
NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuanttopart15ofthe
FCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhentheequipmentisoperated
inacommercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin
accordancewiththeinstructionmanual,maycauseharmfulinterferencetoradiocommunications.Operationofthisequipmentina
residentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillberequiredtocorrecttheinterferenceathisown
expense.
Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatethe
equipment.
UseonlyanRFshieldedcablethatwassuppliedwiththedisplaywhenconnectingthisdisplaytoacomputerdevice.
Topreventdamagewhichmayresultinreorshockhazard,donotexposethisappliancetorainorexcessivemoisture.
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
EnvisionPeripheralsInc.
490NMcCarthyBlvd,Suite#150
Milpitas,CA95035
USA

86BDL4152T
iv
Europe – EU Declaration of Conformity
ThisdevicecomplieswiththeessentialrequirementsoftheRadioEquipmentDirective(2014/53/EU).Thefollowingtestmethodshavebeenappliedin
ordertoprovepresumptionofconformitywiththeessentialrequirementsoftheRadioEquipmentDirective(2014/53/EU):
-EN60950-1/EN62311/EN300328/EN301893/EN301489
Europe Statement
IMPORTANT NOTE:
 Thedeviceisrestrictedtoindooruseonlywhenoperatinginthe5150to5350MHzfrequencyrange.

AT BE BG HR CY CZ DK
EE FI FR DE EL HU IE
IT LV LT LU MT NL PL
PT RO SK SI ES SE UK
Radiation Exposure Statement:
 ThisequipmentcomplieswithCEradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledand
operatedwithminimumdistance20cmbetweentheradiator&body.
 Thefrequency,modeandthemaximumtransmittedpowerinEUarelistedbelow:
 2412-2472MHz(802.11g6Mbps):19.98dBm
 2402-2480MHz(EDR3Mbps):9.65dBm
 2402-2480MHz(LE1Mbps):9.80dBm
 5180-5240/5260-5320/5500-5700MHz(802.11acVHT40MCS0/NSS1):22.95dBm
Taiwan:
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Caution:
Anychangesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatethisequipment.
Thistransmittermustnotbeco-locatedoroperatinginconjunctionwithanyotherantennaortransmitter.
Operationsinthe5GHzproductsarerestrictedtoindoorusageonly.
Radiation Exposure Statement:
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperated
withminimumdistance20cmbetweentheradiator&yourbody.

86BDL4152T
v
Canada:
IndustryCanadastatement:
ThisdevicecomplieswithRSS-247oftheIndustryCanadaRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcause
harmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
CedispositifestconformeàlanormeCNR-247d’IndustrieCanadaapplicableauxappareilsradioexemptsdelicence.Sonfonctionnementestsujetaux
deuxconditionssuivantes:(1)ledispositifnedoitpasproduiredebrouillagepréjudiciable,et(2)cedispositifdoitacceptertoutbrouillagereçu,ycompris
unbrouillagesusceptibledeprovoquerunfonctionnementindésirable.
Radiation Exposure Statement:
ThisequipmentcomplieswithISEDradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperated
withminimumdistance20cmbetweentheradiator&yourbody.
Déclarationd’expositionauxradiations:Cetéquipementestconformeauxlimitesd’expositionauxrayonnementsISEDétabliespourunenvironnement
noncontrôlé.Cetéquipementdoitêtreinstalléetutiliséavecunminimumde20cmdedistanceentrelasourcederayonnementetvotrecorps.
Polish Center for Testing and Certication Notice
Theequipmentshoulddrawpowerfromasocketwithanattachedprotectioncircuit(athree-prongsocket).Allequipmentthatworkstogether(computer,
display,printer,andsoon)shouldhavethesamepowersupplysource.
Thephasingconductoroftheroom’selectricalinstallationshouldhaveareserveshort-circuitprotectiondeviceintheformofafusewithanominalvalue
nolargerthan16amperes(A).
Tocompletelyswitchofftheequipment,thepowersupplycablemustberemovedfromthepowersupplysocket,whichshouldbelocatednearthe
equipmentandeasilyaccessible.
Aprotectionmark“B”conrmsthattheequipmentisincompliancewiththeprotectionusagerequirementsofstandardsPN-93/T-42107andPN-89/
E-06251.

86BDL4152T
vi
Electric, Magnetic and Electromagnetic Fields (“EMF”)
1. Wemanufactureandsellmanyproductstargetedatconsumers,which,likeanyelectronicapparatus,ingeneralhavetheabilitytoemitandreceive
electromagneticsignals.
2. OneofourleadingBusinessPrinciplesistotakeallnecessaryhealthandsafetymeasuresforourproducts,tocomplywithallapplicablelegal
requirementsandtostaywellwithintheEMFstandardsapplicableatthetimeofproducingtheproducts.
3. Wearecommittedtodevelop,produceandmarketproductsthatcausenoadversehealtheffects.
4. Weconrmthatifitsproductsarehandledproperlyfortheirintendeduse,theyaresafetouseaccordingtoscienticevidenceavailabletoday.
5. WeplayanactiveroleinthedevelopmentofinternationalEMFandsafetystandards,enablingustoanticipatefurtherdevelopmentsinstandardization
forearlyintegrationinitsproducts.
Information for U.K. only
(A)
(B)
WARNING -THIS APPLIANCE MUST BE EARTHED.
Important:
Thisapparatusissuppliedwithanapprovedmoulded13Aplug.Tochangeafuseinthistypeofplug
proceedasfollows:+
1. Removefusecoverandfuse.
2. FitnewfusewhichshouldbeaBS13625A,A.S.T.A.orBSIapprovedtype.
3. Retthefusecover.
Ifthettedplugisnotsuitableforyoursocketoutlets,itshouldbecutoffandanappropriate3-pin
plugttedinitsplace.
Ifthemainsplugcontainsafuse,thisshouldhaveavalueof5A.Ifaplugwithoutafuseisused,thefuse
atthedistributionboardshouldnotbegreaterthan5A.
NOTE: Theseveredplugmustbedestroyedtoavoidapossibleshockhazardshoulditbeinserted
intoa13Asocketelsewhere.
How to connect a plug
Thewiresinthemainsleadarecolouredinaccordancewiththefollowingcode:
BLUE-“NEUTRAL”(“N”)
BROWN-“LIVE”(“L”)
GREEN&YELLOW-“EARTH”(“E”)
1. TheGREEN&YELLOWwiremustbeconnectedtotheterminalintheplugwhichismarkedwith
theletter“E”orbytheEarthsymbolorcolouredGREENorGREEN&YELLOW.
2. TheBLUEwiremustbeconnectedtotheterminalwhichismarkedwiththeletter“N”orcoloured
BLACK.
3. TheBROWNwiremustbeconnectedtotheterminalwhichmarkedwiththeletter“L”or
colouredRED.
Beforereplacingtheplugcover,makecertainthatthecordgripisclampedoverthesheathofthelead
-notsimplyoverthethreewires.
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRADIGOMATTHUVUDBRYTAREOCHUTTAGÄRLÄTÅTKOMLIGA,NÄRDUSTÄLLERDINUTRUSTNINGPÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRGVEDPLACERINGENFOR,ATNETLEDNINGENSSTIKOGSTIKKONTAKTERNEMTTILGÆNGELIGE.

86BDL4152T
vii
Paikka/Ilmankierto
VAROITUS:
SIJOITALAITESITEN,ETTÄVERKKOJOHTOVOIDAANTARVITTAESSAHELPOSTIIRROTTAAPISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅRDETTEUTSTYRETPLASSERES,MÅDUPASSEPÅATKONTAKTENEFORSTØMTILFØRSELERLETTEÅNÅ.
China RoHS
根据中国大陆《电子电气产品有害物质限制使用标识要求》，以下部分列出了本产品中可能包含的有害物
质的名称和含量。
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
外壳 ○ ○ ○ ○ ○ ○
液晶显示屏 ×○ ○ ○ ○ ○
电路板组件*×○ ○ ○ ○ ○
电源适配器 ×○ ○ ○ ○ ○
电源线/连接线 ×○ ○ ○ ○ ○
遥控器 X ○ ○ ○ ○ ○
本表格依据SJ/T 11364 的规定编制。
*: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
上表中打“×”的部件，应功能需要，部分有害物质含量超出GB/T 26572规定的限量要求，但符合欧盟RoHS
法规要求（属于豁免部分）。
备注：上表仅做为范例，实际标示时应依照各产品的实际部件及所含有害物质进行标示。
10 環保使用期限
此標識指期限(十年)，電子電氣產品中含有的有害物質在正常使用的條件下不會發生外泄或突變，電子
電氣產品用戶使用該電子電氣產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。

86BDL4152T
viii
《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品
回收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。
娤⌈
㨢᳸$䵥ᵥ⍿Ʋ◦䏝㯹䉭❁ᳫ濕媣ᵥ⍿⊭侻󰵹廞ノ㒞䵽䏳ⴰㄮƲ◦店䢋⾃⁳᳉濕⊭侻斾堿䏦ヵ
⪷ⴰㄮ悅⊔⃅⩜⊭圊䕂㉨㑻Ʋ
單元
限用物質及其化學符號
鉛
(Pb)
汞
(Hg)
鎘
(Cd)
六價鉻
(Cr+6)
多溴聯苯
(PBB)
多溴二苯醚
(PBDE)
塑料外框 ○ ○ ○ ○ ○ ○
後殼 ○ ○ ○ ○ ○ ○
液晶面板 － ○ ○ ○ ○ ○
電路板組件 － ○ ○ ○ ○ ○
底座 ○ ○ ○ ○ ○ ○
電源線 － ○ ○ ○ ○ ○
其他線材 － ○ ○ ○ ○ ○
遙控器 － ○ ○ ○ ○ ○
喇叭（選配） － ○ ○ ○ ○ ○
風扇（選配） － ○ ○ ○ ○ ○
備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考2.〝－〞係指該項限用物質為排除項目。
警語 : 使用過度恐傷害視力。
注意事項 :
(1) 使用30分鐘請休息10分鐘。
(2) 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。
警告使用者 :
此為甲類資訊技術設備 , 於居住環境中使用時 , 可能會造成射頻擾動 , 在此種情況下 , 使用者會被
要求採取某些適當的對策。
Turkey RoHS:
TürkiyeCumhuriyeti:EEEYönetmeliğineUygundur
Ukraine RoHS:
ОбладнаннявідповідаєвимогамТехнічногорегламентущодообмеженнявикористаннядеякихнебезпечнихречовинвелектричномута
електронномуобладнанні,затвердженогопостановоюКабінетуМіністрівУкраїнивід3грудня2008№1057

86BDL4152T
ix
End-of-Life Disposal
YournewPublicInformationDisplaycontainsmaterialsthatcanberecycledandreused.Specializedcompaniescanrecycleyourproducttoincreasethe
amountofreusablematerialsandtominimizetheamounttobedisposedof.
PleasendoutaboutthelocalregulationsonhowtodisposeofyourolddisplayfromyourlocalPhilipsdealer.
(For customers in Canada and U.S.A.)
Thisproductmaycontainleadand/ormercury.Disposeofinaccordancetolocal-stateandfederalregulations.Foradditionalinformationonrecycling
contactwww.eia.org(ConsumerEducationInitiative)
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
Thismarkingontheproductoronitspackagingillustratesthat,underEuropeanDirective2012/19/EUgoverningusedelectricaland
electronicappliances,thisproductmaynotbedisposedofwithnormalhouseholdwaste.Youareresponsiblefordisposalofthis
equipmentthroughadesignatedwasteelectricalandelectronicequipmentcollection.Todeterminethelocationsfordroppingoffsuch
wasteelectricalandelectronic,contactyourlocalgovernmentofce,thewastedisposalorganizationthatservesyourhouseholdorthe
storeatwhichyoupurchasedtheproduct.
Attention users in United States:
PleasedisposeofaccordingtoallLocal,StateandFederalLaws.Forthedisposalorrecyclinginformation,contact:www.mygreenelectronics.comor
www.eiae.org.
End of Life Directives-Recycling
YournewPublicInformationDisplaycontainsseveralmaterialsthatcanberecycledfornewusers.
PleasedisposeofaccordingtoallLocal,State,andFederallaws.
Restriction on Hazardous Substances statement (India)
Thisproductcomplieswiththe“E-Waste(Management)Rules,2016”CHAPTERV,rule16,sub-rule(1).WhereasNewElectricalandElectronic
EquipmentandtheircomponentsorconsumablesorpartsorsparesdonotcontainLead,Mercury,Cadmium,HexavalentChromium,polybrominated
biphenylsandpolybrominateddiphenylethersbeyondamaximumconcentrationvalueof0.1%byweightinhomogenousmaterialsforlead,mercury,
hexavalentchromium,polybrominatedbiphenylsandpolybrominateddiphenylethersandof0.01%byweightinhomogenousmaterialsforcadmium.
exceptofexemptionssetinSchedule2oftheRule.
E-Waste Declaration for India
Thissymbolontheproductoronitspackagingindicatesthatthisproductmustnotbedisposedofwithyourotherhouseholdwaste.
Insteaditisyourresponsibilitytodisposeofyourwasteequipmentbyhandingitovertoadesignatedcollectionpointfortherecycling
ofwasteelectricalandelectronicequipment.Theseparatecollectionandrecyclingofyourwasteequipmentatthetimeofdisposal
willhelptoconservenaturalresourcesandensurethatitisrecycledinamannerthatprotectshumanhealthandtheenvironment.
FormoreinformationaboutE-wastepleasevisithttp://www.india.philips.com/about/sustainability/recycling/index.pageandtoknow
whereyoucandropoffyourwasteequipmentforrecyclinginIndiapleasecontactonbelowgivencontactdetails.
Helplinenumber:1800-425-6396(MondaytoSaturday,9a.m.to5:30pm)
CentralizedE-wastecollectioncenter
Address:TPVTechnologyIndiaPrivateLimited,
59,MaheswariNagar,1stMainRoad,MahadevapuraPost,WhiteeldRoad
Bangalore,Karnataka,PIN:560048,Tel:080-3023-1000
E-mail:[email protected]

86BDL4152T
x
Batteries
ForEU:Thecrossed-outwheeledbinimpliesthatusedbatteriesshouldnotbeputtothegeneralhouseholdwaste!Thereisaseparate
collectionsystemforusedbatteries,toallowpropertreatmentandrecyclinginaccordancewithlegislation.
Pleasecontactyourlocalauthorityfordetailsonthecollectionandrecyclingschemes.
ForSwitzerland:Theusedbatteryistobereturnedtothesellingpoint.
Forothernon-EUcountries:Pleasecontactyourlocalauthorityforcorrectmethodofdisposaloftheusedbattery.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be separated
to collect by local service.
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial ou
e/ou baterias
rede de assistência técnica
autorizada.
Information for EAC
Month and year of manufacturing please refer information in Rating label.
Name and location of manufacturer ООО “Профтехника”
Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия
Importer and information
Наименование организации: ООО “Профтехника”
Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия
Контактное лицо: Наталья Астафьева,
[phone]
[e-mail]

86BDL4152T
xi
Table Of Contents
1. Unpacking and Installation.......................................................1
1.1. TransportationandUnpacking.............................................1
1.2. PackageContents........................................................................4
1.3. InstallationNotes.........................................................................4
1.4. MountingonaWall....................................................................5
1.5. MountinginPortraitOrientation.......................................6
2. Parts and Functions...................................................................7
2.1. ControlPanel.................................................................................7
2.2. Input/OutputTerminals.............................................................8
2.3. RemoteControl........................................................................10
2.4. SDcardCover...........................................................................14
2.5. 4GModule...................................................................................14
2.6. RubberCover.............................................................................15
3. Connecting External Equipment.......................................... 16
3.1. ConnectingExternalEquipment(DVD/VCR/
VCD)...............................................................................................16
3.2. ConnectingaPC.......................................................................16
3.3. ConnectingAudioEquipment...........................................17
3.4. ConnectingMultipleDisplaysinaDaisy-chain
Conguration..............................................................................18
3.5. IRconnection..............................................................................19
3.6. IRPass-throughConnection...............................................20
3.7. TouchOperation......................................................................21
4. Operation................................................................................. 23
4.1. WatchtheConnectedVideoSource............................23
4.2. ChangePictureFormat.........................................................23
4.3. Overview.......................................................................................23
4.4. MediaPlayer.................................................................................25
4.5. Browser..........................................................................................28
4.6. PDFPlayer....................................................................................30
4.7. CMND&Play.............................................................................33
4.8. CustomApp................................................................................34
5. Setting........................................................................................ 35
5.1. Wi-Fi(availablewhenWi-Fidongleisinserted)....35
5.2. Ethernet..........................................................................................35
5.3. More(availablewhen4Gmoduleisconnected)...35
5.4. SignageDisplay...........................................................................35
5.5. Display.............................................................................................43
5.6. Apps.................................................................................................43
5.7. Security...........................................................................................44
5.8. Date&time.................................................................................44
5.9. Developeroptions...................................................................44
5.10. About..............................................................................................44
5.11. Supplementary...........................................................................45
6. OSD Menu ............................................................................... 47
6.1. NavigatingtheOSDMenu................................................47
6.2. OSDMenuOverview...........................................................47
7. Supported Media Formats .................................................... 56
8. Input Mode............................................................................... 58
9. Pixel Defect Policy.................................................................. 60
9.1. PixelsandSub-Pixels...............................................................60
9.2. TypesofPixelDefects+DotDenition....................60
9.3. BrightDotDefects...................................................................60
9.4. DarkDotDefects.....................................................................61
9.5. ProximityofPixelDefects...................................................61
9.6. PixelDefectTolerances.........................................................61
9.7. MURA.............................................................................................61
10. Cleaning and Troubleshooting.............................................. 62
10.1. Cleaning..........................................................................................62
10.2. Troubleshooting.........................................................................63
11. Technical Specications ......................................................... 65

86BDL4152T
1
1. Unpacking and Installation
1.1. Transportation and Unpacking
Notice for transportation
• Alwayskeepthecartoninaverticalposition.
DoNOTplacethecartoninanyotherdirection.
• DoNOTplaceanyobjectonthecarton. • DoNOTapplyshock/vibrationtotheproduct.
• Movethecartonbystacker. • DoNOTdroptheproduct.Strongimpactsmay
damagethecomponentsinside.
• Movesinglecartonwithsmallpalletbystacker.
Carton
Small Pallet
Big Pallet

86BDL4152T
2
Notice for transportation
1. Removethestraparoundthecarton.
2. Useabladetocutthetapeonthetopandopenthecarton.
3. Takeoutthecushionscarefully.
4. Removetheplasticcartonlockersandthetopcarton.

86BDL4152T
3
5. Movethedisplayfromthecartonbytwoadultswithbothhands.
• Donottouchthescreenofdisplaytoavoidpossible
scratches.Movethedisplaybyholdingthehandles.
• Keepthedisplayverticallywhenmovingit.
90°90°
• Placethedisplayverticallyanditsweightshouldspreadevenlyonthesurface.

86BDL4152T
4
Before installing the display
• Thisproductispackedinacarton,togetherwiththestandardaccessories.
• Anyotheroptionalaccessorieswillbepackedseparately.
• Movethedisplaybyatleasttwo(2)adults.
• Afteropeningthecarton,ensurethatthecontentsarecompleteandingoodcondition.
1.2. Package Contents
Pleaseverifythatyoureceivedthefollowingitemswithyourpackagecontent:
• LCDdisplay
• Quickstartguide
• RemoteControlandAAAbatteries
• Powercord
• RS232cable
• RS232daisychaincable
• IRsensorcable
• HDMIcable
• USBcablex2(1forPC,1forOPS)
• DipoleAntennax2
• SDcardcoverX1
• M3screwx1
• M2screwx3
• Logo
* The supplied power cord varies depending on destination.
Quick start guide
Remote Control
and AAA Batteries
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
IDSET ENTER
Power Cord RS232 Daisy Chain CableRS232 Cable
HDMI Cable SD card cover M3
IR Sensor Cable
Dipole Antenna x2 M2 Logo
Touch USB x2
LCD Display

*Itemsmaydifferindifferentlocations
*Displaydesignandaccessoriesmaydifferfromtheimagesshown..
NOTES:
• Forallotherregions,applyapowercordthatconformstotheACvoltageofthepowersocketandhasbeenapprovedbyandcomplieswiththe
safetyregulationsoftheparticularcountry(TypeH05W-F,2Gor3G,0.75or1mm2shouldbeused).
• Keepthepackagingmaterialsappropriatelyafterunpackingtheproduct.
1.3. Installation Notes
• Onlyusethepowercableprovidedwiththisproduct.Ifanextensioncordisrequired,pleaseconsultyourserviceagent.
• Theproductshouldbeinstalledonaatsurface,ortheproductmaytipover.Leaveaspacebetweentherearoftheproductandthewallforproper
ventilation.Donotinstalltheproductinakitchen,bathroomoraplaceexposedtomoisture,failuretodosomayshortenthelifeoftheinternal
parts.
• Donotinstalltheproductwhereitis3000mandhigherinaltitude.Failuretodosomayresultinmalfunctions.

86BDL4152T
5
1.4. Mounting on a Wall
Tomountthisdisplayonawall,astandardwall-mountingkit(commerciallyavailable)isrequired.Itisrecommendedthatyouuseamountinginterfacethat
compliedwithTUV-GSand/orUL1678standardinNorthAmerica.
Protective Sheet
VESA Grid
Table
1. Prepareaatandhorizontalsurfacethatislargerthanthedisplayandspreadathickprotectivesheetonittofacilitateyouroperationwithout
scratchingthescreen.
2. Ensureyouhaveallaccessoriesforalltypesofmounting(wallmount,ceilingmount,tablestand,etc).
3. Followtheinstructionsthatcamewiththebasemountingkit.Failuretofollowthecorrectmountingprocedurescouldresultindamagetothe
equipment,orinjurytotheuserorinstaller.Theproductwarrantydoesnotcoverthedamagecausedbyimproperinstallation.
4. Forthewall-mountingkit,usetheM8mountingscrews(withalength15mmlongerthanthethicknessofthemountingbracket)andtightenthem
securely.
5. Weightoftheunitwithoutbase=96.21kg.Theequipmentanditsassociatedmountingfacilitiesstillremainsecureduringthetest.UseonlytheUL
listedWallMountBracketwithaminimumweight/loadof96.21kg.
1.4.1. VESA Grid
86BDL4152T 600(H)x400(V)mm
Caution:
Topreventthedisplayfromfalling:
• Forwallorceilingmounting,werecommendthatyouinstallthedisplaywithmetalbracketswhicharecommerciallyavailable.Fordetailedinstructions
abouttheinstallation,refertotheguideprovidedwiththebracket.
• Topreventthedisplayfromfallingincaseofearthquakeorothernaturaldisaster,pleaseconsultthemanufacturerofthebracketforthemounting
location.
• Asthisproductishighandheavy,theinstallationofthisproductisrecommendedtobeperformedbyfourtechnicians.
Ventilation Requirements for enclosure locating
Leaveaspaceof100mmatthetop,rear,rightandleftofthedisplayforventilation.
100 mm 100 mm
100 mm
100 mm

86BDL4152T
6
1.5. Mounting in Portrait Orientation
Thisdisplaycanbeinstalledinportraitposition.
1. Ifthetablestandisattached,removeitrst.
2. Rotatethedisplaycounterclockwiseby90°.The“ ”logoshouldbeinaverticalpositionwhenfacingthedisplayfromtheback.
90
90
1.5.1. How to remove the logo
1. Prepareapieceofpaperwithacuttingareaoflogoasaprotectorto
preventthefrontbezelfromscratching.
2. Useaknifeandcarefullyremovethelogostickerwiththepaperplacing
beneath.
3. Tearoffthelogosticker.
123
NOTE: Werecommendyoucontactaprofessionaltechnicianwheninstallingthedisplayonawall.Wearenotresponsibleforanydamagetothe
productiftheinstallationisnotperformedbyaprofessionaltechnician.

86BDL4152T
7
2. Parts and Functions
2.1. Control Panel
MUTE INPUT MENU
1 2 3 4 5 6 7 8
9
1[ ] button
TurnthedisplayOnorturnthedisplaytostandbymode.
2[MUTE] button
Mutethesoundorreactivatesound.
3[INPUT] button
Selectaninputsource.
4[ ] button
IncreasetheadjustmentwhileOSDmenuisOn,orincreasethe
audiooutputlevelwhileOSDmenuisOff.
5[ ] button
DecreasetheadjustmentwhileOSDmenuisOn,ordecreasethe
audiooutputlevelwhileOSDmenuisOff.
6[ ] button
MovetheselecteditemonelevelupwhiletheOSDmenuisOn.
7[ ] button
MovetheselecteditemoneleveldownwhiletheOSDmenuisOn.
8[MENU] button
ReturntothepreviousmenuwhiletheOSDmenuisOn.This
buttoncanalsobeusedtoactivatetheOSDmenuwhentheOSD
menuisOff.
9
Remote control sensor and power status indicator
• Receivecommandsignalsfromtheremotecontrol.
• IndicatetheoperatingstatusofthedisplaywithoutOPS:
-LightgreenwhenthedisplayisturnedOn
-Lightredwhenthedisplayisinthestandbymode
-When{SCHEDULE}isenabled,thelightblinksgreenandred
-Ifthelightblinksred,itindicatesthatafailurehasbeen
detected
-Lightsoffwhenthemainpowerofthedisplayisturnedoff
* Use an IR sensor cable for better remote control performance.
(Please refer to the instructions on 3.5)

86BDL4152T
8
2.2. Input/Output Terminals
100-240V
50-60Hz 2.5A
22
20
24
16
17
18
19
21
23
25
26
27
28
1 3 4 5 7 9 10 11 12 14 15
2 6 8 13
VGA IN
USB
Service Port
DP IN
DP OUT
EXT. SPK
TERMINAL
SPEAKER
SWITCH
AUDIO IN
AUDIO OUT
IR-IN
IR-OUT
SPDIF
OUT
DVI IN
RS232
OUT
RS232
IN
MICRO SD LAN
RS232
HDMI1 IN HDMI2 IN HDMI3 IN
USB
Service Port
DP OUT
USB 2.0
USB 3.0
TOUCH
1AC IN
ACpowerinputfromthewalloutlet.
2MAIN POWER SWITCH
SwitchthemainpowerbetweenOnandOff.
3AC OUT
ACpowersupplytotheACINjackofamediaplayer.
4DisplayPort OUT
AndroidDisplayPortout.
5USB PORT
ConnecttoaUSBstoragedevice.
6USB SERVICE PORT
ConnecttoaUSBstoragedeviceforupdatingAndroidADB
Firmware.
NOTE:Reservedforupdatingthermwareonly.
7MICRO SD CARD
InsertaMicroSDcard.
8RJ-45
TheLANcontrolfunctionisusedforsendingtheremotecontrol
signalfromthecontrolcenterinordertoinstalltheoptionalOPS
module.
9RS232C
AndroidRS232networkinputisreservedforcustomizedprotocol
usagefromSystemIntegrator.
10 HDMI1 IN / 11 HDMI2 IN / 12 HDMI3 IN
ConnecttoasourcedeviceviaanHDMIcable.
13 RS232C IN / 14 RS232C OUT
RS232Cnetworkinput/outputfortheloop-throughfunction.
15 DVI IN
ConnecttoasourcedeviceusingaDVIcable.
16 DisplayPort IN / 17 DisplayPort OUT
DisplayPortvideoinput/output.
18 VGA IN (D-Sub)
VGAvideoinput.
19 IR IN / 20 IR OUT
IRsignalinput/outputfortheloop-throughfunction.
NOTES:
• Theremotecontrolsensorofthisdisplaywillstopworkingifthe
jack[IR IN]isconnected.
• ToremotelycontrolyourA/Vdeviceviathisdisplay,refertopage
20forIR Pass Throughconnection.
21 SPDIF OUT
Digitalaudiooutput
22 AUDIO IN
AudioinputforVGAsource(3.5mmstereophone).
23 AUDIO OUT
AudiooutputforexternalAVdevice.
24 SPEAKER SWITCH
InternalspeakerOn/Offswitch.
25 SPEAKERS OUT
Audiooutputforexternalspeakers.
26 USB SERVICE PORT
ConnecttoaUSBstoragedeviceforupdatingthermwareofthe
mainboard.
NOTE:Reservedforupdatingthermwareonly.

86BDL4152T
9
27 Touch USB
Touch connector to PC.
28 OPS SLOT
Slot for installing the optional OPS module.
2.2.1. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace the batteries:
1. Press and then slide the cover to open it.
2. Insert the batteries with the correct polarity (+) and (–).
3. Replace the cover.
Caution:
Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below:
• Insert “AAA” batteries with the correct polarity (+ and -).
• Do not mix battery types.
• Do not use a new battery with a used one together. Otherwise, it may cause leakage or shorten the life of the batteries.
• Remove the dead batteries immediately to avoid battery leakage in the battery compartment. Do not touch exposed battery acid, as it may cause
injury to your skin.
NOTE: Remove the batteries from the battery compartment when not using for an extended period of time.
2.2.2. Handling the remote control
• Do not drop or apply shock to the remote control.
• Do not allow any liquid to get inside the remote control. If water has entered the remote control, wipe the remote control with a dry cloth
immediately.
• Do not place the remote control near heat and steam sources.
• Do not attempt to disassemble the remote control, unless you need to place batteries in the remote control.
2.2.3. Operating range of the remote control
Point the top front of the remote control at the remote sensor on the display when you press the
buttons.
Use the remote control within a distance of less than 5m/16ft from the display’s sensor, and a
horizontal and vertical angle of less than 30°.
NOTE: The remote control may not function properly when the remote control sensor on the
display is under direct sunlight or strong illumination, or when there is an object between
the remote control and the remote sensor of the display.
3030