Alpha CONNECT User manual

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide

Schedule Mode
In Manual Mode you will
permanently override the schedule.
Exit Manual Mode by switching
to Schedule or turning off the
thermostat.
Frost protection temperature can be set between 5.0ºC and
9.0ºC. To turn on Frost Mode activate Off Mode or Holiday Mode
via the App.
Frost Mode can also be de-activated or activated on the device,
by pressing the frost button once.
After the Holiday Mode ends, the thermostat will follow the
previous setting (Schedule, Manual or Off.)
RXBC605 App
Features available only on the App:
• Temperature format
• Clock format
• Time zone
• Daylight Saving Time
• Heating or Cooling Mode
• Temperature accuracy
• Display tolerance
• Temperature offset
• Schedule/Manual/Off Mode
• Holiday Mode
• Location Mode
• Delay Start
Download the ALPHA CONNECT
App, create an account and
register your device. Follow
the on screen instructions to
complete all the steps.
Customize your setttings according to
your preferences. Time and date will be
set automatically once connected to the
internet. Set the mode (heat/cool). Heat
Mode is used for controlling a heating boiler.
Cool Mode is used for controlling a cooling
device. In Cool Mode, you can choose
temperature accuracy between ± 0.5 °C and
± 0.25 °C. In Heat Mode, you can select as
well between a lower comfort level (6 on/off
cycles per hour) and a higher comfort level
(9 on/off cycles per hour). Also, in order to
calibrate the temperature, you can offset it
using a ± 3 °C range.
Registration
All 5/2 Individual
Set one
schedule
for the
entire
week
(each day
the same)
Set a
schedule
for the
working
days and
for the
weekend
Set a daily
schedule
(each day
different)
1
4
321
13
2
1 2 3
00000000
00000000
00
23 4
6 7
5
iIf the internet connection is lost the thermostat will follow
the schedule. If it was in Frost Mode you can disable the
Frost function from the device and continue following
the schedule (see Frost Mode section of the guide).
There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24
hours), 2. Manual and 3. Off.
Location Mode is an automated task
designed to change your heating settings
according to the current distance from your
home.
1
If Location Mode is enabled, you can drag
the slider in order to set the distance limit.
Go to “Setting” to manage your settings.
2
Frost Mode
General Operation
Device Settings Via the App
Select the period for this function. Frost Mode temperature will be
activated during this period.
Holiday Mode
Location Mode

Schedule Mode
In Manual Mode you will
permanently override the schedule.
Exit Manual Mode by switching
to Schedule or turning off the
thermostat.
Frost protection temperature can be set between 5.0ºC and
9.0ºC. To turn on Frost Mode activate Off Mode or Holiday Mode
via the App.
Frost Mode can also be de-activated or activated on the device,
by pressing the frost button once.
After the Holiday Mode ends, the thermostat will follow the
previous setting (Schedule, Manual or Off.)
RXBC605 App
Features available only on the App:
• Temperature format
• Clock format
• Time zone
• Daylight Saving Time
• Heating or Cooling Mode
• Temperature accuracy
• Display tolerance
• Temperature offset
• Schedule/Manual/Off Mode
• Holiday Mode
• Location Mode
• Delay Start
Download the ALPHA CONNECT
App, create an account and
register your device. Follow
the on screen instructions to
complete all the steps.
Customize your setttings according to
your preferences. Time and date will be
set automatically once connected to the
internet. Set the mode (heat/cool). Heat
Mode is used for controlling a heating boiler.
Cool Mode is used for controlling a cooling
device. In Cool Mode, you can choose
temperature accuracy between ± 0.5 °C and
± 0.25 °C. In Heat Mode, you can select as
well between a lower comfort level (6 on/off
cycles per hour) and a higher comfort level
(9 on/off cycles per hour). Also, in order to
calibrate the temperature, you can offset it
using a ± 3 °C range.
Registration
All 5/2 Individual
Set one
schedule
for the
entire
week
(each day
the same)
Set a
schedule
for the
working
days and
for the
weekend
Set a daily
schedule
(each day
different)
1
4
321
13
2
1 2 3
00000000
00000000
00
23 4
6 7
5
iIf the internet connection is lost the thermostat will follow
the schedule. If it was in Frost Mode you can disable the
Frost function from the device and continue following
the schedule (see Frost Mode section of the guide).
There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24
hours), 2. Manual and 3. Off.
Location Mode is an automated task
designed to change your heating settings
according to the current distance from your
home.
1
If Location Mode is enabled, you can drag
the slider in order to set the distance limit.
Go to “Setting” to manage your settings.
2
Frost Mode
General Operation
Device Settings Via the App
Select the period for this function. Frost Mode temperature will be
activated during this period.
Holiday Mode
Location Mode

Schedule Mode
In Manual Mode you will
permanently override the schedule.
Exit Manual Mode by switching
to Schedule or turning off the
thermostat.
Frost protection temperature can be set between 5.0ºC and
9.0ºC. To turn on Frost Mode activate Off Mode or Holiday Mode
via the App.
Frost Mode can also be de-activated or activated on the device,
by pressing the frost button once.
After the Holiday Mode ends, the thermostat will follow the
previous setting (Schedule, Manual or Off.)
RXBC605 App
Features available only on the App:
• Temperature format
• Clock format
• Time zone
• Daylight Saving Time
• Heating or Cooling Mode
• Temperature accuracy
• Display tolerance
• Temperature offset
• Schedule/Manual/Off Mode
• Holiday Mode
• Location Mode
• Delay Start
Download the ALPHA CONNECT
App, create an account and
register your device. Follow
the on screen instructions to
complete all the steps.
Customize your setttings according to
your preferences. Time and date will be
set automatically once connected to the
internet. Set the mode (heat/cool). Heat
Mode is used for controlling a heating boiler.
Cool Mode is used for controlling a cooling
device. In Cool Mode, you can choose
temperature accuracy between ± 0.5 °C and
± 0.25 °C. In Heat Mode, you can select as
well between a lower comfort level (6 on/off
cycles per hour) and a higher comfort level
(9 on/off cycles per hour). Also, in order to
calibrate the temperature, you can offset it
using a ± 3 °C range.
Registration
All 5/2 Individual
Set one
schedule
for the
entire
week
(each day
the same)
Set a
schedule
for the
working
days and
for the
weekend
Set a daily
schedule
(each day
different)
1
4
321
13
2
1 2 3
00000000
00000000
00
23 4
6 7
5
iIf the internet connection is lost the thermostat will follow
the schedule. If it was in Frost Mode you can disable the
Frost function from the device and continue following
the schedule (see Frost Mode section of the guide).
There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24
hours), 2. Manual and 3. Off.
Location Mode is an automated task
designed to change your heating settings
according to the current distance from your
home.
1
If Location Mode is enabled, you can drag
the slider in order to set the distance limit.
Go to “Setting” to manage your settings.
2
Frost Mode
General Operation
Device Settings Via the App
Select the period for this function. Frost Mode temperature will be
activated during this period.
Holiday Mode
Location Mode

Schedule Mode
In Manual Mode you will
permanently override the schedule.
Exit Manual Mode by switching
to Schedule or turning off the
thermostat.
Frost protection temperature can be set between 5.0ºC and
9.0ºC. To turn on Frost Mode activate Off Mode or Holiday Mode
via the App.
Frost Mode can also be de-activated or activated on the device,
by pressing the frost button once.
After the Holiday Mode ends, the thermostat will follow the
previous setting (Schedule, Manual or Off.)
RXBC605 App
Features available only on the App:
• Temperature format
• Clock format
• Time zone
• Daylight Saving Time
• Heating or Cooling Mode
• Temperature accuracy
• Display tolerance
• Temperature offset
• Schedule/Manual/Off Mode
• Holiday Mode
• Location Mode
• Delay Start
Download the ALPHA CONNECT
App, create an account and
register your device. Follow
the on screen instructions to
complete all the steps.
Customize your setttings according to
your preferences. Time and date will be
set automatically once connected to the
internet. Set the mode (heat/cool). Heat
Mode is used for controlling a heating boiler.
Cool Mode is used for controlling a cooling
device. In Cool Mode, you can choose
temperature accuracy between ± 0.5 °C and
± 0.25 °C. In Heat Mode, you can select as
well between a lower comfort level (6 on/off
cycles per hour) and a higher comfort level
(9 on/off cycles per hour). Also, in order to
calibrate the temperature, you can offset it
using a ± 3 °C range.
Registration
All 5/2 Individual
Set one
schedule
for the
entire
week
(each day
the same)
Set a
schedule
for the
working
days and
for the
weekend
Set a daily
schedule
(each day
different)
1
4
321
13
2
1 2 3
00000000
00000000
00
23 4
6 7
5
iIf the internet connection is lost the thermostat will follow
the schedule. If it was in Frost Mode you can disable the
Frost function from the device and continue following
the schedule (see Frost Mode section of the guide).
There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24
hours), 2. Manual and 3. Off.
Location Mode is an automated task
designed to change your heating settings
according to the current distance from your
home.
1
If Location Mode is enabled, you can drag
the slider in order to set the distance limit.
Go to “Setting” to manage your settings.
2
Frost Mode
General Operation
Device Settings Via the App
Select the period for this function. Frost Mode temperature will be
activated during this period.
Holiday Mode
Location Mode

ALPHA CONNECT THERMOSTAT
Installation Guide
Introduction
Alpha Connect is a Smart phone controlled programmable
thermostat. The thermostat will switch your heating system on
or off, as needed, in accordance with the temperature set by you,
locally on the device or remotely using the dedicated app.
Installation - Step 1
iThe thermostat is pre-set from factory in Manual Mode
allowing you to set the desired temperature. This is the
default working mode if not connected to the internet
during installation.
1. RXBC605
Install receiver and connect wiring as shown in boiler manual.
Turn power on to boiler before inserting batteries into the
thermostat.
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your
equipment completely dry. Disconnect your equipment before
cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED
2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of
Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm
Installation - Step 3
3. iTG310
Connect the gateway to your router.
Gateway is online when the green LED is on.
Issue date: DEC2020
Version: V0016
HEAD OFFICE
Alpha Heating Innovation
Nepicar House
London Road
Wrotham Heath
Kent
TN15 7RS
For Technical Help or Service call :
0344 871 8764
These instructions have been carefully prepared but we reserve the right to alter the specification
at any time in the interest of product improvement.
www.alpha-innovation.co.uk
Button Functions
TEST/PAIRING
1
2
3
4
5
Decrease button
4
Test Mode/ Pairing Mode
5
Turn on the LCD backlight
Turn On/Off the Frost Mode
1
2
Increase button
3
Installation - Step 2
2. ALPHA CONNECT THERMOSTAT
Before inserting the batteries, please make a note of
your SRT number and register your device on the app.
SRT
123
TEST / PAIRING
SRT0000000-00
TEST / PAIRING
+ −
+ −
2. Press and hold the Test/Sync button on your thermostat for
5 seconds then release. The thermostat should display words
“SYNC 9”. A 9 minute countdown will appear on thermostat’s
screen.
1. Press and hold the Sync button on your receiver for 5 seconds
then release, the red led will flash every second.
3.The pairing process is over when the LED stops flashing and
disappears.
4. The countdown on the thermostat’s screen will continue.
Once the pairing process is successful, there is no need for
you to wait for the the countdown to stop. To return to normal
display, press and hold the Test/Sync button on your thermostat
for 5 seconds.
5. You may now use your thermostat.
TEST / PAIRING
5 sec
TEST / PAIRING
Re-pairing Process
Before the pairing process, please ensure that the switch
button on the receiver is next to the white circle in the AUTO
position. Also, please ensure that the distance between the
thermostat and the receiver is at least 1m. If you need to re-
pair your thermostat with the receiver, follow the next steps:
iThe thermostat and the receiver are pre-paired from
factory.
5 Sec
TEST / PAIRING
5 sec
Remove the connector between red wires 3 & 4 and
plug all wires onto the matching numbers on the receiver.
4
Fix the RF receiver in place using screws provided.
5
6
1
2
Access the control panel as shown in the boiler manual.
3
DO NOT remove link wire between terminals 1 & 2 on
the boiler.
Replace the front panel.
Power up the boiler and check correct operation.
RXBC605 Wiring Terminals
Terminal Identifier Description
1 N Neutral
2 L Live input (230V AC)
3COM Common terminal (volt free)
4 N.O. Normally Open (volt free)
TEST / PAIRING
5 sec
ALPHA CONNECT THERMOSTAT
Installation Guide