Alpine Power Beam PLM310T User manual

PLM310T
Power Beam
Set of 3, 10 Watt Lights w/
Transformer
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, and Pond Supplies & More. All of our products are
constructed from the highest quality materials. In the event that we have not achieved our usual
standard of excellence, we will repair or replace, at our discretion, within the warranty period. A valid
proof of purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
•Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper storage
that allows water to freeze within a product may cause damage, is considered negligence,
and will not be covered under this warranty. The use of “hard water,” and/or caustic cleaners,
can affect the painted or other finishes. Failure to keep the unit clean, and use of such
additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for
some splashing to occur and protecting the immediate surfaces is not the responsibility of
Alpine Corporation.
•Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up using
standard paint. The paint is designed to protect the entire finish against breakdown of
color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading, within the first year from date of
purchase, with the above exclusion.
•Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to show
proof of purchase, provide photographs and any other information needed to validate your
claim. This may be necessary to distinguish between a partial or complete replacement of
a defective product. The warranty does not cover any items with multiple parts; the
warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department. Item is covered under one year limited warranty from the date of
purchase. When requesting replacement parts due to a warranty claim after 30 days
of purchase, credit card information will be requested for shipping charges.
•Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to:
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim.
3

Caution: Before assembling and operating please
read the entire manual
Must be operated with a transformer (included):
Before reading instructions below, this light MUST BE used with a transformer.
Use with Alpine multi-light transformer which comes included in the packaging.
Please use a transformer with the correct wattage and never exceed the
maximum wattage indicated on the transformer.
Operating Instructions:
•Before plugging in the unit, be sure the input voltage indicated on your
transformer is the same as your local power supply. If not, please do not
operate the light until you obtain the appropriate transformer from your
local dealer.
•To reduce the risk of electrical shock, inspect all cords for damage before
installation.
•Plug the connector of the Power Beam™ Light into the socket on the
transformer and screw the coupling until tight.
•Plug the transformer into the nearest 120-volt outlet. Your Power Beam™
Light should light up.
Changing the MR11 Bulb or Colored Lenses to your Power Beam™:
•To replace the MR11 volt 10 watt halogen bulb, first make sure to unplug
the transformer and remove it from the water (if submerged).
•After allowing a sufficient amount of time for the light to cool down, let it
dry and remove the lens retainer from the Power Beam™ light by pushing
on it and turning counter-clockwise quickly.
•Remove the lens carefully and make sure the “O” ring stays in place and
is not lost during this process.
•Gently pull out the socket and remove the MR11 bulb and replace with
the new MR11 12 volt 10 watt bulb by aligning the pins of the bulb into
the socket. Gently push the new bulb down, DO NOT force it. Turn the
MR11 12 volt 10 watt bulb around if it does not fit easily.
•Re-Install the lens and lens retainer ensuring the “O” ring remains in the
correct position in the groove of the Power Beam™ light.
1
2
•To maintain a good water tight seal, make sure the lens is flush with the
front lip of the rubber seal.
•To charge your Power Beam™ color lens, remove the lens and replace it
with a colored lens of your choice.
•Make sure the lens is on the rubber seal then take the cover and place it
correctly onto the slots of the Power Beam™ turning tightly clockwise.
•Make sure the cover is tightly locked.
Limited Warranty Information:
For complete limited warranty information and details,
please visit our website at www.alpine4u.com
3 X 10 Watt Low Voltage Power Beam™ Lights can be used indoor or
outdoor, out of water or in water. Light must be used with provided Alpine
transformer at all times.
Troubleshooting your Power Beam™:
If light fails to illuminate, please check the following:
•Check that the light set is getting power by testing another applicant in the power
outlet that the lights use.
•Check to ensure that your light bulb has not burned out from usage.
•If water gets into any of your Power Beam™ lights, lift it out of the water, remove the
lens and empty the water until dry.
Caution & Warning:
•Always handle the light from the base. The light housing can and will become HOT!
•Operating the lights with missing or damaged covers can result in risk of fire or
electrical shock.
•Use ONLY recommended MR11 12 volt 10 watt halogen bulbs.
•Do not exceed the voltage & wattage indicated on the transformer.
•Keep away from flammable and/or children.
•This light assembly has not been tested or designed for use in swimming pools and
hot tubs.