Altair 52269 Manual

Parts List
No. Part Name Qty (pcs) Pic
Maintenance & Instructions A Bar 4
B Screw 4
C Nut 12 (8 pcs pre-assembled on
tub)
D Washer 12 (8 pcs pre-assembled on
tub)
E Fastener washer 4
FAdjustable metal
feet 4
TOOLS REQUIRED
Step 1
* Turn over the tub on soft surface to make sure it is protected from scratches.
* Take off the plastic covers of screws and unscrew nuts and washers from the
tub(pre-assembled on the tub).
* Place the bars on the tub, position washers and screws, then fix the screws
but not tighten them, because the bars could be adjusted during assembling.
Important:
* Two people are required for installation.
* Freestanding tub is not designed to take weight on the rim.
Do not sit or stand on the tub rim.
Altair Inc.
Do not tighten the
screws before
adjustment.
Please retain this manual after installation for future reference and
maintenance
Product must be installed in compliance with relevant Water
Bylaws
The Product is CUPC certified
Original certification model Code: DM1003-1.7 File No. 10288
Adjustable Wrench
Adjustment
space
52269-BAT-WH-MB

Step 2
Cleaning & Maintenance:
* Position the feet on the bar, fasten with washers, fastener washers and screws, A) To preserve the polished surface, after using your tub, clean with soft
but not tighten screws right away. cloth and warm soapy water to wash away any body oils or soap residue
* Adjust the feet to match the shape of the tub, bars could be adjusted if needed. that forms a ring tide mark.
* Hold the feet firmly when tightening all screws, the feet must be secured fully to B) Do not use powders, pastes, crème cleaners, thinners, window cleaning
prevent any movement. sprays or dry cleaning liquid, etc.
C) When coloured essentials oils are used, first test that the colour won't
stain your tub. Always add oils into a tub full of water. Never pour them
into an empty tub.
* Pay attention to below points if the tub is designed with tap deck.
* The tap holes are not pre-drilled on the deck, drill holes according to your need.
* Check and siliconed the tap holes to make sure the reinforcement layer holes are
solid before installing the faucet.
Step 3
* Check and make sure that there is no water leakage at the faucet.
* Assemble the overflow and waste. Connect the tub trap (not supplied with the tub)
to the fitted tub waste and connect that to the bathroom's waste pipes.
Step 4
* Place the tub to the desired location and water test the tub for any leaks before use.
Receive Your Tub
A) Unpack and check for damage.
After receiving your tub, please unpack and remove all covering, checking
whether there is any damage. Repack the tub if it is not being immediately
installed. It will be rejected any claim for damage if not notified in a timely
manner.
B) Protect your tub.
Before commencing installation, ensure the tub is completely protected, leave
covering in place until the bathroom is complete. Scratches and cracks incurred
during installation are not covered by the warranty.
Illustrations below are for reference only
A : Bar
F : Adjustable feet
D: Washers
E: Fastener washer
C: Nut
Tap Holes Area
52269-BAT-WH-MB
Altair Inc.

Important:
We recommend that this product is installed by a qualified professional contractor.
Do NOT overtighten the waste as this may cause long term damage to the bath.
Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric acid or phosphoric acid.
1. Remove cap, screw and gasket from fitting;
3. Tighten the screw to the overflow body;
4. Aim another side to the drain hole and screw the pop up cover slowly, but donot
overtighten it;
5. Loosen the screws on the three pipes and strentch the pipes to the appropriate length,
fitting for the bathtub, and then tighten the screws.
6. Connect approproate drain pipe;
7. Check if there's any leakage.
52269-BAT-WH-MB
Altair Inc.