Altec Lansing SHOCKWAVE 100 User manual

Quick Start Guide
Item: IMT7001

Quick Start Guide
IMT7001
IMT7001 Wireless
Party Speaker
Adapter
AUX. Audio cable
Wired Mic.x1

AUX:To connect devices via auxiliary
cable
USB OUT: For charging mobile devices
DC IN: Power adapter port
MIC2: For 2nd wired microphone
MIC1: For 1st wired microphone
INPUT/OUTPUT PORTS

Play/Pause
Previous song/
change FM station
Next song/change
FM station
Adjust Bass level
Press and hold for 3 seconds to
turn speaker ON and OFF
FM and AUX modes
Bluetooth/Stero
Pairing mode
Light mode
Adjust speaker volume
Brief introduction to buttons on top panel
Press MIC volume buttons to
increase or decrease the volume of
each microphone
MIC Volume Control
：Power Button:
(BT mode only)
Hold: FM Scan

ALShockwave 100
BLUETOOTH CONNECTION
Stereo pairing (requires two speakers) :
1. Have one speaker turned on, paired, and playing music. It will serve as the
HOST (the Primary speaker). The display will be showing ‘Bt’. (Pair by pressing the
BT/PAIR button, ‘Bt’ flashes on the display screen and becomes solid when pairing
is complete.
2. Turn on an additional compatible speaker, it will serve as the Secondary
speaker.
3. Press and hold the BT/PAIR button on the Primary speaker for approximately
two seconds or until the display changes from solid ‘Bt’ to flashing ‘HOSt’.
4. Quickly press the BT/PAIRbutton on the Secondaryspeaker. The display will change
from flashing ‘Bt’ to flashing ‘St PAIr’ (stereo pairing).
5. The speakers will connect and both displays will show ‘Bt’. The speakers
will now play the same music from the same audio source, one will play Left and
one will play Right.
Go to the Bluetooth settings page on your phone. Make sure Bluetooth
is on before connecting to the available device “AL Shockwave 100”.
Primary Speaker Secondary Speaker

LIGHTING CONTROL
Lights
(Noted: Cone’s light will be displayed while unit is playing music)
Briefly press the LIGHTS button for lighting control:
LED 1: Side lights scrolling multi-color, cones color change with the beat;
press and hold to change as single color scrolls one by one.
Side lighting one colore, cones follow music to flash the same color;
press and hold for 3 seconds to change color.
L267 x W238 x H504 (mm)
15V 1.5A
LED 2: Sides and cones follow music and change color automatically every 3
seconds.
LED 3:
LED 4: Sides o and cones flash into one color; press and hold for 3 seconds
to change color.
LED 5: Sides do a bar graph from the middle in one color and cones flash the
same color; press and hold for 3 seconds to change color.
LED 6: Sides and cones slowly change colors automatically every 3 seconds;
press and hold to turn the cone lights o.
LED 7: Sides flash one color and cones are o. Press and hold for 3 seconds
to change color.
LED 8: Sides do a multi-color bar graph from the middle and cones flash.
Sides fade between colors and cones are o.
Lighting o.
LED 9:
OFF:
Power Audio: 43W (RMS) 150W (Peak) Total
Driver Units: 5.25” x 2+2” x 1
Seperation: ≥40dB
S/N: ≥70dB
Distortion: ≤o.5% (1K, 1W)
DC Input:
Dimension:
Length of adaptor: 110cm
Length of Audio cable(stereo-to-stereo): 90cm
Length of wired micphone’s cable: 285cm

Call us 24/7 at 1-855-292-4087 or
email us at [email protected]
or visit us at alteclansing.com
Having Trouble?
We’re here to help!