Altec Lansing Shockwave 200 User manual

IMT7100
SHOCKWAVE 200
180W

IMT7100
Quick Start Guide UL Adaptor
IMT7100
SHOCKWAVE 200
180W

Press and hold button for 3 seconds to
power on or power off speaker
Brief introduction to buttons on top panel
Power Button：
Play/Pause (BT mode only),
AUX mode: Short press MUTE
Previous song Next song
Reset to default settings:
Press and hold the BASS button for 10S to reset all settings back to factory default.
Light Modes:
Briefly press to turn on the lighting.
Cycles through 9 modes and
then back to off
FM Mode:
Briefly press to enter into FM mode
AUX mode:
Briefly press to enter into AUX mode
BT & Party-sync Button:
Briefly press to enter into Bluetooth pairing mode,
Press and hold for Bluetooth disconnect,
Double-click for party-sync connect or disconnect
Bass Modes:
Briefly press to cycle through 3 bass
modes, Standard (flat), Bass Enhance
1 and Bass Enhance 2

AL Shockwave 200
Bluetooth Connection
Party-sync with AL SHOCKWAVE Family
Go to the Bluetooth settings menu on your phone. Make sure
that Bluetooth is turned on. Connect to the device listed
as “AL Shockwave 200”
If needed briey press the BT button to enter into BT mode;
Item Number Item name Pairing Name
IMT7000
IMT7100
IMT7200
IMT7300
Shockwave Wireless Party Speaker AL Shockwave
Shockwave 200 Wireless party speaker
Shockwave 300 Wireless Party Speaker
Shockwave 400 Wireless Party Speaker
AL Shockwave 200
AL Shockwave 300
AL Shockwave 400
ALShockwave 200
If you want to change to a dierent BT device when already paired press and
hold the BT button, the speaker will disconnect from its paired device. A dierent
device can now be paired.
A double press of the BT button is used to enter/exit party-sync mode on
extra speakers if you have them as below.

LIGHTING CONTROL
The Altec Lansing SHOCKWAVE family has four members that support party-sync.
You can mix and match between any of these four models, setting up one
speaker as the primary unit connected to up to 100 other speakers all playing
in sync.
1. Connect one speaker to your Bluetooth device in the normal way via Bluetooth.
2. Double press the BT button on this rst speaker to enter Party sync and
make it the primary speaker.
3. Double-press the BT button on the next speaker to enter Party-sync mode,
its BT LED will ashes slowly and it will nd and connect to the rst (primary)
speaker.
4. Repeat No 3 if you have more speakers you want to connect.
5. To exit party-sync double press the BT button on the speakers you wish
to disconnect and return to normal operation.
Notes:
Playback volume is adjusted via the rst (primary) speaker.
The BT playback controls only operate on the rst (primary) speaker.
Turning o the rst (primary) speaker turns o all speakers.
All secondary speakers can be turned on/o individually and their light modes
changed via their individual controls.
Briey press the LIGHTS button to switch lighting mode.
(Note: Some modes which use ‘sound-to-light’ need music playing to be visible)
Mode 1: Rotating ring in three colors
Mode 2: Flashing to music
Mode 3: ‘Spectrum’
Mode 4: ‘Stacking/re-stacking’ lights both sides
Mode 5: Rotating lights in multi-colors
Mode 6: Breathing on/o
Mode 7: Flashing to music, solid lighting when no audio
Mode 8: ‘Bar-graph’ in multi-colors
Mode 9: Rotating ‘stacking/re-stacking’ lights
Each press moves to the next mode and back round to o.

Descriptions about the various ports on the speaker
INPUT/OUTPUT PORTS
Knob to adjust the volume of microphone
Input socket for wired microphone
USB OUT:
For charging your mobile devices
LINE IN (AUX-IN):
For connecting the line level output or headphone
output of mobile devices or CD players etc.
DC IN:
charging your speaker from the PSU
Charging-in indicator:
Solid red when charging, will be off when fully charged
RESET:
Button is recessed inside.
For use only in the unlikely case of a lock up.
Use paperclip or pin to perform restart of the speaker.
USB-A output: 5V 1A
Power Audio: 180W (Peak) Total
Driver Units: 2 x 5.25” Bass + 2” Tweeter.
S/N: ≥70dB
Distortion: ≤0.5%(1K,1W)
USB-C charging Input: 19V 1.5A
Length of UL Adaptor cable: 110cm
Dimensions: L223*H465*D190 mm