Altelix NP141105-DIN User manual

IS0133 Rev B 11/14/19
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [e-mail] www.altelix.com
Copyright (C) 2019 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or RegisteredTrademarks of Altelix LLC.
Specificationsare subjectto change without notice. See www.altelix.com for most current information
Page-4 NP141105/NP171406 DIN Enclosure Guide
WARNING: INSTALLATION OF THIS PRODUCT NEAR POWERLINES IS
DANGEROUS. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS
Under some conditions, this enclosure may not prevent electrocution. Users should keep
enclosure away from any overhead wires. If enclosure contacts a power line, any initial
protection could fail at any time. IF ENCLOSURE NEARS ANY OVERHEAD WIRES,
IMMEDIATELY LET GO, STAY AWAY, AND CALL UTILITY COMPANY
THIS ENCLOSURE IS DESIGNED TO BE INSTALLED ONLY BY A TRAINED PROFESSIONAL
INSTALLER
Warning: To avoid electric shock, grounding must be installed by the installer as part of the
installation. The unit must be grounded and installed in accordance with National Electrical
Codes (NEC) and any local codes. Note that non-metallic enclosures do not provide
grounding between conduit connections.
Warning: Enclosure must be secured using a pad-lock when energized to prevent
unauthorized access and shock hazard.
Important: Look over the site before beginning installation, and anticipate possible hazards.
Select a safe site to install the enclosure.
If you have power lines in the area, call your local electric utility for assistance.
NEVER work alone; always have someone near who can summon help.
Check weather conditions. Be sure that the area is not slippery and make sure that rain or
thunderstorms are not predicted for the day you install the enclosure.
If you need to use a ladder, make sure it is made of non-conductive (non-metallic) material.
Enclosures improperly installed or installed to an inadequate structure are susceptible to
wind damage that can be very serious or even life threatening. Ensure that the installation is
properly grounded. Ensure that the enclosure is properly secured and structurally sound to
support all loads (weight, wind & ice).
Rooftop Installation Warning
DO NOT assume that just because you're on a roof, you're isolated from ground. You may
still be electrocuted or fall off the roof.
Got Questions?
We are here to help.
Contact us at:
[e-mail]
USA & Canada: 866-660-9434
International: [phone]
When mounting, ensure the rubber bonded washers completely cover the
enclosure mounting holes to provide a water-tight seal. Silicone sealant
can also be added to enhance the seal.
Wall Mounting
Mounting Hole Dimensions
NP141105-DIN NP171406-DIN
Note:
Drilling Templates can be download by visiting www.ALTELIX.com in the
Resources section.
Shown with Equipment Mounting Plate Removed for Clarity

Page-2
Wall Mounting
Page-3
NP171406-DIN Shown
1. Using a ¼” drill bit, drill two
holes into the rear of the
enclosure at the locations shown.
The NP141105-DIN and NP171406-DIN enclosures can be wall mounted using
the supplied hardware or pole mounted using the optional NMK Series pole
mounting kits available from www.ALTELIX.com.
2. Drill wall as required. See
mounting hole dimensions on
page 3.
Included with the enclosure are
(4) Rubber Bonded Washers and
(4) Screws with Wall Anchors.
Drill Locations
Top of Enclosure
3. Place Rubber Bonded
Washers onto the Screws
as shown.
4. Secure the enclosure to wall using the (4) screws in locations shown.
NP141105-DIN Shown
1. Install the Equipment Mounting Plate into the enclosure as shown
using the supplied (4) self-tapping screws.
2. Install the DIN rails onto the equipment mounting plate as shown
using supplied #8-32 screws and washers. Threaded holes are
provided in the plate for mounting.
Installing Equipment Mounting Plate & DIN Rails
Equipment Mounting Plate
DIN Rails
Additional DIN Rails for both the NP141105-DIN and NP171406-DIN are
available from www.ALTELIX.com
(Note: Installing additional DIN Rails will require mounting holes to be drilled in the
equipment mounting plate)