Altera EN5319QI User manual

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
EN5319QI1.5ASynchronousDC/DC Converter
Evaluation Board User Guide
Introduction
Thank you for choosing Altera Enpirion power products!
This evaluation board user guide applies to the EN5319 devices mounted on PCB’s with
the part number 08251 rev A on the backside. This user guide should be used together
with the latest device datasheet. The datasheet can be found at
www.altera.com/enpirion.
Following are the features of this evaluation board.
•Populated with one EN5319QI 1.5A PowerSoC with integrated inductor.
•Pre-tinned pads are available for a wide range of input and output capacitor
configurations.
•There are four positions available for the output capacitors. The first position,
closest to the IC, can accommodate a 1206, 0805, or 0603 case size while the
other three positions can accommodate either 0805 or 0603 capacitor case
sizes.
•The base output capacitor configuration is 2 x 22uF 0603 MLCC.Refer to the
product datasheet for output capacitor requirements.
•There are two positions for the input capacitors. The first position, closest to the
IC, can accommodate an 0805 or 0603 case size while the other position can
accommodate an 0805 case size. The base input capacitor configuration is a
single 10uF 0805 MLCC. Refer to the product datasheet for input capacitor
requirements.
•Output voltage programming is accomplished via a simple resistor divider.
Jumpers are provided for 4 pre-configured output settings. These settings are as
follows:
•1.0V, 1.2V, 1.5V, 1.8V
•Easy jumpers are provided for the following signals:
•Enable
•Numerous test points are provided as well as clip leads for input and output
connections
•The board comes with input decoupling and reverse polarity protection.
Page 1 of 6
www.altera.com/enpirion

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
Quick StartGuide
Figure 1 shows a photograph of the evaluation board. Please refer to this figure while
configuring the board for evaluation.
STEP 1: Set the “ENABLE” jumper to the Disable Position.
STEP 2: Select the desired VOUT voltage setting by placing the jumper J2 on the
correct jumper pin. Figure below shows the VOUT jumper options and their
nominal voltages. Note that depending on the tolerance of the resistors
populated on the board, each output voltage setting may have a larger
tolerance than just the VFB pin as specified in the datasheet. Please see
Figure 3 and the Bill of Materials section. Multiple jumpers can be populated to
get other output voltages not listed below. With the resistors shown below, if all
4 jumper positions are populated, the output voltage will be approximately
3.7V. Note that for any VOUT higher than 3.3V, the output capacitors need to
be changed to 2 x 22uF/0805.
CAUTION:the VOUT jumper settings can only be changed when the device is
off. Failure to follow this guideline may result in damage to the part.
Please note: The loop compensation circuit for this evaluation board has been
chosen for a wide range of VIN and VOUT values. In order to optimize the loop for
any specific VIN/VOUT operating point, please see the compensation table in the
datasheet. See Figures 1 and 3.
STEP 3: Connect a Power Supply to the input power connectors, VIN (J4) and GND
(J5). DO NOT turn the power supply on yet.
DISABLE
ENABLE
Page 2 of 6
www.altera.com/enpirion

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
CAUTION:Be mindful of the input voltage magnitude and polarity. Even though
the evaluation board comes with reverse polarity protection diodes, it may not
protect the device under all conditions.
STEP 4: Connect an electronic load, or load board to the load to the output connectors
VOUT (J6) and GND (J7).
STEP 5: Turn on the input supply, and move the ENABLE jumper to the enabled
position. The EN5319QI is now powered up.
Figure 1. Evaluation Board top view.
J2 VOUT Jumpers
C9 = Ca
ENABLE
Output Capacitors
Input Capacitor
Page 3 of 6
www.altera.com/enpirion

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
TestRecommendations
To guarantee measurement accuracy, the following precautions should be observed:
Make all input and output voltage measurements at the board using the test
points provided (TP5 to TP8). This will eliminate voltage drop across the line and
load cables that can produce false readings.
Measure input and output current with series ammeters or accurate shunt
resistors. This is especially important when measuring efficiency.
Use a low-loop-inductance scope probe tip similar to the one shown in Figure 2
to measure switching signals and input / output ripple to avoid noise coupling into
the probe ground lead. Input ripple, output ripple, and load transient deviation are
best measured near the respective input / output capacitors. For more accurate
ripple measurement, please see Enpirion App Note regarding this subject
(www.altera.com/enpirion).
Figure 2.Recommended probe configuration.
If you need to measure radiated EMI, place a 10uF/0805, X7R capacitor at the
input and output edges of the PCB (C13 and C14 positions), and connect the
PVIN power and the load to the board at or near these capacitors. The added
capacitor at the input edge is for high-frequency decoupling of the input cables.
The one added at the output edge is meant to represent a typical load decoupling
capacitor.
Page 4 of 6
www.altera.com/enpirion

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
EvaluationBoardSchematic
Figure 3. Engineering Evaluation board schematic.
TP12
1
2
TP13
1
2
R8
C11
0603
TP14 TP15
Short across R8 when all
other routing completed
SCH 06783
PCB 08251
C3
C1
C4
C10
C5
C6
FB1
TP2
1
2
TP1
1 2
VOUT
Vin
Vin
TP5 1
TP6 1
TP7 1
TP8
1
ENABLE
R1
R2
+
C8
Vin
Input Protection
1206
0805
0805
0805
0805
0805
C9
0805
0805
0805 0805 0805 0805
C13
C14
VOUT
C12
J4
J6
J5
J7
0805
TP16
TP17
TP18
TP19
VOUT
VIN
PGND
POK
GND
GND
VOUT
VIN
TP10
1
TP31
TP4 TP11
J1
1
2 3
D1
U1
EN53x9
NC(SW)1
1
PGND
2
PGND
3
VOUT
4
VOUT
5
VOUT
6
VOUT
7
PGND
8
PGND
9
TST2
10
TST1
11
TST0
12
AVIN 16
AGND 15
VFB 14
NC(13) 13
NC(SW)24 24 NC(SW)23 23
NC(SW)22 22 NC(SW)21 21
PVIN 20
PVIN 19
ENABLE 18
POK 17
J2
1 3
5
2
4 6
87
R3
R5
R6
R4
R7
TP9
1
C1, C4-6 should be
combination 0805/0603.
C3 should be combination
1206/0805/0603.
Page 5 of 6
www.altera.com/enpirion

Enpirion®Power EvaluationBoardUser Guide
EN5319QI PowerSoC
Bill of Materials
Designator
Qty
Description
C1, C10
2
CAP CER 10UF 10V 10% X7R 0805
C3, C4
2
CAP CER 22UF 6.3V X5R 0603
C8
1
CAPACITOR, SMTELECTROLYTIC, 150UF, 20%,10V
C9
1
CAP CERM 6.8PF 50V NP0 0805
C11
1
CAPACITOR CER 1UF 10V X5R 0603
C5, C6, C12-C14,
R8
6 NOT USED
D1
1
TVS UNIDIRECT 600W 6.5V SMBJ6.5A
FB1
1
SMT FERRITE BEAD4A 0805, Wurth Electronik 742792012
J1
1
CONNECTOR HEADER, 3 POSITION, Samtec ASP-121920-02
J2
1
CONNECTOR HEADER, 8 POSITION Dual, Samtec TSW-104-24-T-D
J4-J7
4
BANANA JACK,KEYSTONE 575-4
R1, R3
2
RES 348K OHM 1/8W 1%0805
R2
1
RES 523K OHM 1/8W 1%0805 SMD
R4
1
RES 100K OHM 1/8W 1%0805 SMD
R5
1
RES 232K OHM 1/8W 1%0805 SMD
R6
1
RES 174K OHM 1/8W 1%0805 SMD
R7
1
RES ZERO OHM 1/8W 5% 0805 SMD
TP5-TP9,
TP16-TP19
9 TESTPOINT SURFACE MOUNT, KEYSTONE 5016
U1
1
EN5319QI QFN 1.5A
ContactInformation
Altera Corporation
101 Innovation Drive
San Jose, CA 95134
Phone: [phone]
www.altera.com
© 2013 Altera Corporation—Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX,
MEGACORE,NIOS,QUARTUSandSTRATIX wordsand logosare trademarksof Altera Corporation and registered in the U.S.
PatentandTrademarkOfficeand in other countries. All other wordsand logosidentified astrademarksor service marksare the
property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its
semiconductor products to current specifications in accordance with Altera'sstandard warranty, but reservesthe right to make
changesto any productsand servicesat any time without notice. Altera assumesno responsibility or liability arising out of the
application oruse ofanyinformation,product,orservicedescribedhereinexceptasexpressly agreedtoin writing by Altera. Altera
customersareadvised toobtain thelatestversionofdevicespecificationsbeforerelyingonany published information and before
placing ordersfor productsor services.
Page 6 of 6
www.altera.com/enpirion

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Altera manufacturer:
Other Similar products are found below :
5AGTMC3D3F31I5N 5AGXBA5D4F27I5N 5AGXBA5D4F31C4N EP2S30F672C5 EP4CE6E22A7N EP4CE75F23C8N
EPF10K30ETI144-2 EPM2210GF324C4N EPM7128AETC100-7 5AGXMA5D6F27C6N 5CEFA2F23C7N EP1C20F400C7N
EP2AGX95EF35I5N EP2S90F1020C5N EP3C25F324C8 EP4CE30F23C7 EP4CE75F29I7N EPF10K50VBC356-3N EPM7128AETC144-10
EPM7256SRC208-10 EVB-EN5322QI EVB-EN5329QI EVB-EN6347QI EVB-ER3105DI EVB-EV1320QI EVB-EV1340QI EVB-
EV1380QI 5AGXMA7G6F31C6N 5CEBA4F23C8N 5M160ZM100I5N EPM7064AETC44-10 EP4CE15F23C8N EP4CE115F23C8N
EP4CE10U14I7N EP3C40F484C8N EP3C16E144C8 EP3C120F780I7 EP2C35F484I8N EP2C20F484I8N EP1S10F780C7
EP1AGX60DF780C6N EVB-EN6360QI EVB-EP5382QI EVB-EY1602SI-ADJ EPF10K20RC208-3 EP4CGX110DF27C7N
EP4CE40F29C7N EP1C6F256I7N HAFBSF0200C4AX3 CSNB121