Alvarado VSG-1-SS Operating and safety instructions

VSG/VSGX
WAIST HIGH SECURITY GATE
INSTALLATION & MAINTENANCE GUIDE
Serial Number:
ALVARADO MANUFACTURING COMPANY, INC.
12660 Colony Street, Chino, CA 91710
Tel: [phone] | Toll: (800) 423 –4143 | Fax: [phone]
http://www.alvaradomfg.com/ PUD2996R2-6

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
2
ALVARADO TURNSTILES

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
3
ALVARADO TURNSTILES
TABLE OF CONTENTS
1.0 SAFETY....................................................................................................................5
1.1.0 SAFETY SYMBOLS USED IN THIS HANDBOOK ........................................................................................5
1.2.0 GENERAL SAFETY INFORMATION..........................................................................................................6
1.3.0 IMPORTANT SAFETY PRECAUTIONS......................................................................................................6
1.4.0 IMPORTANT PRE-INSTALLATION NOTES................................................................................................6
2.0 MODELS...................................................................................................................8
2.1.0 OVERVIEW..........................................................................................................................................8
2.2.0 DESCRIPTION......................................................................................................................................8
2.3.0 CONFIGURATIONS...............................................................................................................................9
2.4.0 DIRECTION .........................................................................................................................................9
2.5.0 OPTIONS ..........................................................................................................................................10
3.0 PLAN & ELEVATION VIEWS.................................................................................12
3.1.0 SINGLE DIRECTION GATES /VSG-1 &VSGX-1 MODELS....................................................................12
4.0 SETUP & INSTALLATION .....................................................................................13
4.1.0 PACKAGED COMPONENTS .................................................................................................................13
4.2.0 TOOLS REQUIRED.............................................................................................................................13
4.3.0 SLAB REQUIREMENTS .......................................................................................................................14
4.4.0 POWER REQUIREMENTS....................................................................................................................14
4.5.0 OPERATING ENVIRONMENT................................................................................................................14
4.6.0 OVERVIEW OF INSTALLATION STEPS ..................................................................................................14
4.7.0 LAYOUT &INSTALLATION...................................................................................................................16
4.8.0 ELECTRICAL ACTIVATION &WIRING INSTRUCTIONS.............................................................................18
4.8.1 WIRING INSTRUCTION AT THE GATE LOCATION ...................................................................................18
4.8.2 WIRING INSTRUCTION AT THE CONTROL LOCATION.............................................................................20
4.8.3 INSTRUCTIONS FOR TESTING THE ELECTRICAL GATE ..........................................................................20
4.8.4 LOCK SPECIFICATIONS ......................................................................................................................20
4.8.5 ELECTRICAL LOCK WIRING DIAGRAMS ...............................................................................................21
4.8.6 INSTRUCTIONS FOR TESTING THE ELECTRICAL GATE WITH OPTIONAL PUSH BAR .................................22
APPENDIX A –TROUBLESHOOTING........................................................................23
A.1.0 SYMPTOMS,POSSIBLE CAUSES,&SOLUTIONS ..................................................................................23
APPENDIX B –MAINTENANCE..................................................................................26
B.1.0 MAINTENANCE POINTS......................................................................................................................26
B.1.1 ANCHOR TENSION ............................................................................................................................26
B.1.2WIRING INSPECTION .........................................................................................................................26

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
4
ALVARADO TURNSTILES
B.1.3 LUBRICATION ON PIVOT POINTS ........................................................................................................27
B.1.4 LOCK ALIGNMENT.............................................................................................................................27
B.1.5 EXTERIOR CARE...............................................................................................................................27
APPENDIX C –CLEANING..........................................................................................27
C.1.0 PRIMARY FINISHES:STAINLESS STEEL #4 SATIN FINISH &#8 MIRROR FINISH.....................................27
C.2.0 EXTERNAL COMPONENT FINISHES.....................................................................................................27
APPENDIX D –PARTS LIST .......................................................................................28
D.1.0 VSG/VSGX PARTS LIST ..................................................................................................................28

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
5
ALVARADO TURNSTILES
1.0 SAFETY
1.1.0 Safety Symbols Used in this Handbook
The following symbols are used in this operating instruction manual to indicate potential risks and other
safety information:
FIGURE 1.1.0.1
WARNING!
This symbol is used in this manual to warn installer(s) and/or operator(s) of
potential harm. Please read these instructions very carefully.
FIGURE 1.1.0.2
CAUTION!
This symbol is used in this manual to designate actions or situations which
represent a potential hazard to pedestrians, personnel, property and/or
equipment. Please read these instructions very carefully.
FIGURE 1.1.0.3
NOTE!
This symbol is used in this manual to designate useful information for the
installer(s) and/or operator(s). Please read these instructions very carefully.
FIGURE 1.1.0.4
QUESTION?
For questions, please contact Alvarado at [phone], Monday –Friday,
6:00 AM to 4:30 Pacific Standard Time. Remember to read this manual
completely before installing or operating the gate.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
6
ALVARADO TURNSTILES
1.2.0 General Safety Information
The VSG-1/VSGX-1 Single Direction Waist High Gate has been designed, built, and tested by Alvarado.
Every unit is factory tested for safety and reliability before shipping. However, the unit may present a risk
to persons and property if it is not installed and/or operated correctly. The installation and operating
instructions must therefore be read in their entirety and all safety information contained therein must be
complied with.
The manufacturer shall refuse to accept liability and shall withdraw warranty if this system is used
incorrectly or is used for a purpose for which it was not intended.
If there are questions, you may contact Alvarado at [phone], Monday through Friday, 6:00 AM to
4:30 PM PST.
1.3.0 Important Safety Precautions
Follow the installation and/or operating instructions in this manual along with the following precautions:
The product is designed for indoor use only.
Use only skilled individuals to install and service the gate.
The gate is not a toy. Do not allow children to play on or near the gate. Do not allow horseplay near
the unit.
Follow a proper maintenance schedule.
Do not operate the unit if it has been damaged in any manner. Have the unit repaired or adjusted by a
skilled service person before use.
Do not modify or alter the gate.
In access control applications, train all personnel that will be using the gate in the proper method of
operation. Ensure that as new users are added, they are properly trained.
Do not use non-Alvarado parts.
1.4.0 Important Pre-Installation Notes
The pre-installation notes listed below must be reviewed before installing the gate. These notes also
serve as a checklist after installation that must be complied with. The installation site should also be
evaluated before actual installation of the gate to ensure that future gate placement is possible and
installed as desired. This evaluation includes proper spacing, a firm foundation, and conduit runs for low
voltage power lines. More details of the site preparation may be found in, SECTION 4.0 titled, “Setup &
Installation.”
WARNING
The manufacturer shall refuse to accept liability and shall withdraw warranty if this gate
system is used incorrectly or is used for a purpose for which it was not intended. This
includes incorrect installation of the product and/or mishandling the product. The installation
and operating instructions must therefore be read in their entirety and all safety information
contained therein must be complied with.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
7
ALVARADO TURNSTILES
Follow the pre-installation notes listed below for proper operation of gate:
NOTE
See SECITION 4.0 titled, “Setup & Installation,” for more information; such as: slab
requirements, anchoring centerline dimensions, et cetera…
The gate is designed for indoor use only. Do not expose the gate to outside weather conditions.
Weather conditions may damage the unit and it’s physical appearance.
Both posts must be plumb, level to each other, and square to the gate. This will ensure peak
performance.
Both posts must be firmly bolted to the mounting surface. This will maximize the performance of the
gate and minimize noise from loose “rocking” posts.
All wires connected to the gate must be properly concealed.
Do not sit or place excessive weight on the gate. Doing so will damage the gate, as they’re not
designed to carry additional weight.
Do not make any adjustments to the components inside the gate. The components are tested,
configured, and assembled at the factory.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
8
ALVARADO TURNSTILES
2.0 Models
2.1.0 Overview
The VSG Gate is a manual, waist high, self-closing gate. Various models, configurations, and options
exist for this gate. The following overview will provide a short description of each model:
TABLE 2.1.0.A –VSG Gate Models
Non-Electrical
Electrical
Single
Direction
VSG-1
VSGX-1
For a complete listing of possible gate configurations, see TABLE 2.1.0.B for details. Gates may also be
customized, please contact Alvarado for specific needs.
TABLE 2.1.0.B –Most Common VSG Gate Model Listings with Options
Model Number
Short Product Description
VSG-1-SS
36” Single Direction Manual Gate with Bars
VSG-1P-SS
36” Single Direction Manual Gate with Acrylic Panel
VSGX-1-SS
36” Single Direction, Fail-Safe Electric Mag Lock Gate with Bars
VSGX-1-SS (w/ Push Bar)
36” Single Direction, Fail-Safe Electric Mag Lock Gate with Bars + Push Bar
VSGX-1P-SS
36” Single Direction, Fail-Safe Electric Mag Lock Gate with Acrylic Panel
2.2.0 Description
The following provides a functional description for each model (SEE SECTION 2.3.0 FOR CONFIGURATIONS).
The VSG-1 Gate is a manual, waist high, self-closing gate with a closure mechanism installed on the
hinge post. The gate arm is equipped with a stop tab and swings in one direction. The hinge post
assembly includes a hydraulic dampener to minimize gate arm from slamming.
The VSGX-1 Gate is a manual, failsafe electrical locking, waist high, self-closing gate with a closure
mechanism installed on the hinge post. The gate arm is equipped with a stop tab and swings in one
direction. The hinge post assembly includes a hydraulic dampener to minimize the gate arm from
slamming. An electrically controlled magnetic lock secures the gate when the gate arm has been closed.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
9
ALVARADO TURNSTILES
2.3.0 Configurations
The VSG Gate Models described in the previous sections may be summarized with the following
illustrations.
VSG-1 (Non-Electrical Configuration)
Non-Locking, self-closing gate with a stop tab.
The gate swings in ONE direction.
FIGURE 2.3.0.A – VSG-1 Single Direction Gate
( Non-Locking & Non-Electrical )
ENTRY
HINGE
POST
VSGX-1 (Electrical Configuration)
Electric locking, self-closing gate with a stop tab.
The gate swings in ONE direction.
FIGURE 2.3.0.B – VSGX-1 Single Direction Gate
( Locking & Electrical )
ENTRY
HINGE
POST
NOTE
Application of the VSG/VSGX Gates meet selected guidelines contained in the Americans
with Disabilities Act Accessibility Guidelines (ADAAG) as issued by the Architectural and
Transportation Barriers Compliance Board. However, due to the potential for varying
standards, Alvarado makes no representation regarding the compliance of this product with
any state or local laws or regulations regarding public access.
2.4.0 Direction
The VSG models are supplied in either a right hand or left hand swing.
For description purposes only, the gate swing can be described in reference to the hinge location when
entering the gate by pushing the gate forward.
A Left Hand Gate swings with the hinge on the left when entering the gate (SEE FIGURE 2.4.0.A below).
A Right Hand Gate swings with the hinge on the right when entering the gate (SEE FIGURE 2.4.0.B below).

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
10
ALVARADO TURNSTILES
FIGURE 2.5.0.A – Gate with Infill Bars.
FIGURE 2.5.0.B – Gate with Acrylic Panel.
FIGURE 2.4.0.B – VSG-1 Right Hand Gate
FIGURE 2.4.0.A – VSG-1 Left Hand Gate
ENTRY
ENTRY
HINGE
POST
HINGE
POST
NOTE
The Right Hand Entry Direction and Left Hand Entry Direction terminology is used only to
describe the swing of the gate. The VSG-1 / VSGX-1 Models swing in a single direction. The
direction is referenced to the hinge location. This describes the direction of the gate and
must be specified when ordering.
2.5.0 Options
Other optional configurations:
Insert Style
All VSG/VSGX Models are available with either Infill Bars or a Clear
Acrylic Panel (with or without a Wheelchair Decal). See (FIGURES 2.5.0.A,
2.5.0.B, 2.5.0.C, & 2.5.0.D) for more details.
Finishes
All VSG/VSGX Gates are fabricated from Stainless Steel and come in
#4 Satin Finish.
Fail Safe Operation
For VSGX Models only, the gate unlocks in the event of power loss. The
gate will re-lock when power is supplied.
Panic Bar
For VSGX-1 Models only, a push-release bar opens the gate for emergency
exits. This is an optional component.
The Panic Bar is not available on the Acrylic Panel model VSG.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
11
ALVARADO TURNSTILES
Remote Activation
For VSGX Models only, the gate requires the use of a momentary dry contact switch to lock and unlock.
The gate lock will not re-engage until the switch is released. This switch is a “Momentary Normally
Closed Switch.”
This is an optional component.
When ordering please ask for Alvarado part number 10-1423.
Gate Status Relay
For VSGX Models only, the gate may be configured for remote monitoring of gate open/close status.
This is an optional component.
When ordering please ask for Alvarado part number”MSG-MC.”

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
12
ALVARADO TURNSTILES
3.0 PLAN & ELEVATION VIEWS
3.1.0 Single Direction Gates / VSG-1 & VSGX-1 Models
PLAN VIEW
ELEVATION VIEW
NOTE
Dimensions may vary slightly depending on locking mechanism used. Position the gate
components in the location they will be installed to determine the actual gate dimensions.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
13
ALVARADO TURNSTILES
4.0 SETUP & INSTALLATION
4.1.0 Packaged Components
The following components are included with the order. Determine which VSG/VSGX Model will be
installed. Electrical Gates will require a conduit to supply low power voltage and remote contacts for
control (optional).
VSG-1 (Non-Electrical) Components
1. Latch Post
2. Hinge Post with Gate Arm
3. This Manual
4. Base Package
Qty 2 each –Split Base Cover
5. Anchor Package
Qty 8 each –3/8 Anchors (2” length)
Qty 8 each –3/8 -16 x 2½” HHCS
Qty 8 each –3/8 Flat Washers
VSGX-1 (Electrical) Components
1. Latch Post with Lock Mechanism
2. Hinge Post with Gate Arm
3. This Manual
4. Base Package
Qty 2 Each –Split Base Cover
5. Anchor Package
Qty 8 Each –3/8 Anchors (2” length)
Qty 8 Each –3/8 –16 x 2½” HHCS
Qty 8 Each –3/8 Flat Washers
6. Power Transformer
4.2.0 Tools Required
Heavy Duty Drill or Roto Hammer
Torpedo Level
5/8” Concrete Drill Bit
Chalk Line
Ratchet with 9/16” Socket
Safety Glasses
Torque Wrench
Rubber Mallet
7/32” Allen Wrench
Wire Crimper (VSGX Models)
Shop VAC
Tape Measure
NOTE
For electrically locked gates (VSGX Models) only, cabling will need to be run to the gate
latch post. An electrical conduit is needed to safely provide cabling to power the electrical
lock. Additional cabling to the hinge post is required for gates with the Panic Bar Option.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
14
ALVARADO TURNSTILES
4.3.0 Slab Requirements
SLAB REQUIREMENTS
MINIMUM THICKNESS: 4” ON SOLID LEVEL CONCRETE
DO NOT INSTALL ON ASPHALT
4.4.0 Power Requirements
The electrical gates (VSGX Models) require a low voltage 12 VDC power supply. A power transformer is
provided with each electrical gate. However, it’s the responsibility of the installer to provide the necessary
conduit runs to the gate.
4.5.0 Operating Environment
Recommended Temperature Range for Operation: 0to 50C (air temperature)
Recommended Humidity Range for Operation: 5% to 95% non-condensing
WARNING
This product is designed for indoor use only. Operating the unit outside the suggested range
for temperature and humidity will result in degradation in performance, and can cause harm
to the device.
4.6.0 Overview of Installation Steps
A. Determine gate locations taking into account of power and activation wiring (if applicable).
B. Anchor gate posts.
C. Connect activation wiring (if applicable).
D. Connect power (if applicable).
E. Adjust gate for proper alignment.
F. Test the gate.
NOTE
Determine the VSG Model that will be installed, the direction of operation, and the
conduit runs for power (if the gate is electrical).
Determine if the gate requires an electrical activation signal. If so, provide necessary
conduit runs and review the wiring diagrams (depending on activation type).
Note the installation steps for your particular VSG Gate Model.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
15
ALVARADO TURNSTILES
VSG/VSGX Gate Installation considerations:
In order to ensure the gate will operate as intended, it is very important that the gate posts are correctly
installed and oriented.
If the posts are not installed at the correct distance, set plumb and square, the gate may not open or
close properly and could have an interference fit with the magnetic lock. Under no circumstances should
the hinge pivot or dampener be tampered with. These are pre-set at the factory.
In order to ensure a good installation the following steps are recommended and should be followed in
conjunction with installation instructions:
After locating the post positions, check for a level floor using a masons level or equivalent.
If not level, shim to correct height.
Locate post hole locations, mark hole centers, drill anchor holes and install anchors.
Position the “gate post” and loosely install bolts.
Using a level, adjust the post side to side and front/back position using shims.
The post surface where the gate hinges attach is critical and must be plumb.
Carefully tighten bolts and re-check with a level.
Once bolts are tight, articulate gate to the open position and slowly release it. The gate should
close to the lock position.
Be careful not to over travel beyond the closed position.
If the gate does not close, the post is likely not plumb. Re-check the post using a level and
ensure it is plumb. Re-check for proper operation of the gate.
Position the second post and loosely install bolts.
Using a level, adjust the post side to side and fore/aft position using shims.
Once the post is plumb, measure the post to post distance as per installation drawings and adjust
the post in or out as needed to the distance specified.
Tighten bolts and re-check to ensure post is to specified distance and is plumb.
Check for proper operation of gate, install plate covers.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
16
ALVARADO TURNSTILES
4.7.0 Layout & Installation
Follow the steps provided in this section to layout and install the gate. The references made in this
section refer to the components shown in the diagram below (FIGURE 4.7.0.A).
FIGURE 4.7.0.A
Single Direction Gates, VSG-1 or VSGX-1
Top Bracket
Hinge
Hinge Post
Latch Post
Gate Arm
VSGX-1 Lock
(Only if Provided)
Floor
Lower
Bracket
Hinge
WARNING
Use only skilled individuals to install and service the gate.
Do not modify or alter the gate.
Do not use non-Alvarado parts.
The gate is designed for indoor use only. Do not expose the gate to outside weather
conditions. Weather conditions may damage the unit and it’s physical appearance.
Both posts must be plumb, level to each other, and square to the gate. This will ensure
peak performance.
1. Determine the location where the gate will be installed taking into consideration the minimum width
opening required (See the “Plan & Elevation View” drawings for the minimum installation
requirements). Once the installation location and direction of swing has been determined, snap a
chalk line on the floor to mark the centerline of the gate. The chalked centerline should be at least 4
feet in length (See Figure 4.7.0.C below).
2. Mark the locations (perpendicular to the gate centerline) for the Hinge Post and Latch Post centerlines.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
17
ALVARADO TURNSTILES
NOTE
Determine the VSG Model that will be installed, the direction of operation, and the
conduit runs for power (if the gate is electrical).
Determine if the gate requires an electrical activation signal. If so, provide necessary
conduit runs and review the wiring diagrams (depending on activation type).
Note the installation steps for your particular VSG/VSGX Gate Model.
WARNING
Final dimensions may vary depending on the locking mechanism used. Position the
gate components in the location they will be installed to determine the proper centerline
locations.
For electrically locked gates (VSGX Models) only, cabling will need to be run to the
gate Latch Post. The power cable conduit should terminate flush with the floor at the
intersection of the gate and Latch Post centerlines.
3. Center the Hinge Post at the intersection of the gate and Hinge Post centerlines.
4. Center the Latch Post at the intersection of the gate
and Latch Post centerlines.
5. With the Gate Arm in it’s neutral position (home
position), ensure that the entire unit: Hinge Post, Gate
Arm, and Latch Post are parallel to the gate
centerline. Both posts must be plumb, level to each
other, and square to the gate. This will ensure peak
performance. Also verify proper alignment of the
locking mechanism.
6. Mark the center locations of the four anchor holes
for each post (Hinge Post & Latch Post). Move the
posts to the side and drill a 5/8” diameter hole at the
center of each marked location. Drill each hole 3”
deep (a total of eight holes). For terrazzo, ceramic
tile, or brick veneer installations, add the thickness
of the finished floor material to the anchor hole
depth. See FIGURE 4.7.0.D.
7. Vacuum out the holes thoroughly. If the holes are not clean, the anchors will not tighten.
8. Insert the anchors with the thread side down. One anchor for each drilled hole. Ensure that the
anchors are flush with the concrete floor.
STOP
For Electrical Gates (VSGX) only, review and follow the “Electrical & Activation Wiring
Instructions” before proceeding. Do not proceed further until the electrical conduits are
properly run to the posts and securely connected.
9. Place the Hinge Post back over the anchor holes. Anchor the Hinge Post with (4) each 3/8 –16 x 2 ½”
HHCS bolts and flat washers. Make sure that the installation is level. Do not tighten the bolts
completely.
10. Place the Latch Post back over the anchor holes. Anchor the Latch Post with (4) each 3/8 - 16 x 2 ½”
HHCS bolts and flat washers. Make sure that the installation is level. Do not tighten the bolts
completely.
Vacuum and remove
debris. Insert the
Anchors with the
thread side down.
Ensure the anchors
are flush with the
surface.
Insert the bolt
and tighten.
Drill hole.
Clean Hole.
FIGURE 4.7.0.D – Anchoring the Hinge Post & Latch Post.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
18
ALVARADO TURNSTILES
11. Confirm that the Gate Arm is properly aligned with the Latch Post when the Gate Arm is in the closed
position by ensuring that the Gate Arm, Hinge Post, Latch Post are installed plumb with the floor while
level and square to each other.
WARNING
For safety and operation of the gate, it’s extremely important that the Hinge Post, Gate
Arm, and Latch Post be level. Use a level to verify that the Hinge Post, Gate Arm, and Latch
Post are level horizontally with the floor and vertically level with each other. The Gate
Arm and Latch Post must be at a 90-degree angle.
12. Adjust and shim the post as required to properly align the gate. It is important that the posts be
plumb and level with the floor for the gate arm to self-close and center properly. The gate arm and
latch post must be at a 90-degree angle.
13. Tighten all of the anchoring bolts (8 bolts total) to 20 ft-lbs.
14. Install the (2) halves of the Split Base Cover around the Hinge Post Base Plate using supplied
8 -32 x ¼ screws and secure it by tapping down with a rubber mallet over the hinge post base.
15. Install the (2) halves of the Split Base Cover around the Latch Post Base Plate and secure it by
tapping down lightly with a rubber mallet over the latch post base.
NOTE
For all gates, ensure that all anchoring bolts are tighten to 20 ft-lbs.
For all gates, ensure the Gate Arm and Latch Post is at a 90-degree angle.
For all gates, both posts must be plumb, level to each other, and square to the Gate
Arm. This will ensure peak performance.

16. This completes the installation process.
4.8.0 Electrical Activation & Wiring Instructions
Electrical VSG Gates, such as the VSGX-1 must be connected to a low voltage power source in order to
operate. The following instructions will detail the steps to setup an electrical connection for the electrical
fail-safe locking gates. Additional information provided will also detail the steps of connecting a remote
activation switch or wiring to a Panic Bar Option.
WARNING
Use only skilled individuals to install and service the gate.
Ensure that the unit is completely powered off and all voltage sources are disabled.
Verify that the proper power supply of 12 VDC is supplied before beginning.
4.8.1 Wiring Instruction at the Gate Location
1. Before making any wiring connections verify that the proper power supplied is delivered:
For Single Directional Gates, Part Number: 10-1079 provides 1 A at 12 VDC.
2. Now, make sure that the primary power to the unit is off.
3. Wires from the Power Supply must be connected to the fail-safe electrical lock, located on the Latch
Post. Run the wires up to the Latch Post locations. To do this, pull 18 AWG cable through the conduit
from the transformer power supply such that the low voltage 12 VDC is terminated at the electrical
fail-safe lock on the VSGX gate Latch Post. Ensure that the cable length is sufficient to reach the wires
from the lock.

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
19
ALVARADO TURNSTILES
NOTE
Cable lengths should not exceed 50 feet.
Cables must never be wrapped in coils. This produces interference in signal
activation (VSGX Models ONLY).
4. Locate the “Electrical Lock Wiring Diagrams” in this manual if connecting the Fail-
Safe electrical magnetic lock on the VSGX-1 Model to a switch box. This switch box
contains a “Momentary Normally Closed Switch” that is required for a proper activation
signal.
5. On the gate side of the conduit, install crimp connector receptacles on the conduit
wire leads to properly receive the connectors provided on the lock leads coming out
of the bottom of the gate Latch Post.
6. On the gate side of the conduit, connect the POSITIVE (+) ORANGE/COLORED wire
coming out of the bottom of the gate Latch Post to the POSITIVE (+) conduit lead wire.
Connect the NEGATIVE (-) BLACK wire coming out of the bottom of the gate latch
post to the NEGATIVE (-) conduit lead wire (SEE FIGURE 4.8.1).

Installation & Maintenance Guide
VSG / VSGX || PUD2996R2-6 || 04/13/2012
20
ALVARADO TURNSTILES
4.8.2 Wiring Instruction at the Control Location
1. On the power supply and switch side of the conduit, install crimp connector plugs on the conduit wire
leads to properly connect to the switch and the power supply.
2. Again, on the power supply and switch side of the conduit, connect the POSITIVE (+) conduit lead
wire to the COMMON terminal on the 12 VDC gate activation switch that will be used. Connect the
NEGATIVE (-) conduit lead wire to the NEGATIVE (-) power supply wire. Connect the POSITIVE (+)
power supply wire to the 12 VDC gate activation switch (SEE FIGURE 4.8.5.A. on page 21) Use a
MOMENTARY NORMALLY CLOSED switch for the FAIL-SAFE electric lock.
4.8.3 Instructions for Testing the Electrical Gate
1. Plug the power supply into a 110 VAC power source. The electrical locking gate will be locked when
power is applied. Confirm that this is true.
2. Unplug the power supply. The electrical locking gate will be unlocked upon the loss of power. Confirm
that this is true.
3. Plug the power supply back into the power source. The gate should re-lock as long as the switch is
activated. Press the gate activation button (momentary normally closed switch). If the gate is
functioning correctly the lock will release and the gate will unlock.
4. Open the gate arm. If the gate is functioning correctly the gate arm will self close and automatically
re-lock after the gate arm closes and centers on the latch post.
NOTE
Use a MOMENTARY NORMALLY CLOSED SWITCH to activate the fail-safe
electrical magnetic lock.
4.8.4 Lock Specifications
Specifications:
VSGX-1 (Magnetic Lock)
Part Number:
10-3135
Voltage:
+12 VDC
Current:
1 A @ 12 VDC
Operating Temp:
-40 to +140 F
Shear Holding Force:
~300 lbs. (273 kg)
Details:
Wire Lead
Description
ORANGE/COLORED
+12 VDC Input
BLACK
Ground
This Magnetic Lock only operates in Fail-Safe Mode. When powered, use a “Momentary Normally
Closed Switch” to release the lock. The gate will re-lock after the gate arm closes and centers on the
latch post and aligns with the stop tab (VSGX).