Alvey 65H User manual

Key
Part
Description
Key
Part
Description
1
R6E4
Spindle Screw
15
R6J10
Spindle Fibre Washer
2
R7F2
Drag Handle Plate Lock Nut
16
R6A31
Spindle Titanium
3
R4F22
Handle Set
17
R6J8
Spindle Washer
4
R7E31
Drag Handle Plate Assy
18
R7J7
Drag Pawl
5
R7D19
Drag Star Adjusting Nut
19
R5G5
Drag Pawl Spring
6
R7B/C10
Drag Clutch Washers
20
R5K1
ON/OFF CAM
7
R4A
Spool
21
R7K10
Drag ON/OFF Lever & ACTV
8
R7H6
Fibre Washer Friction Tube
22
R1A
Back Plate Assembly
9
R8A3
Gear Tube & Gear Assy
23
R8C1
S/S Slide Washer
10
R7H3
Friction Tube Washer
24
R6F3
Dome Hex Nut
11
R8A2
Friction Tube/Gear Assy
25
R2G13
Base Lock Spring
12
R8B3
Idler Gear Shaft
26
R2DEF4
Base Bolt, Nut, Washer
13
R8A1
Idler Gear Assembly
27
R2A8
Turbo Cast Index
14
R8B1
Gear Spacer Bush
65H
..STEALTH HYBRID 65..
CONGRATULATIONS and thank you for purchasing our Australian made
Super Light Carbon Fibre High Speed Geared Reel as your choice of
fishing reel. These reels are constructed from the highest quality
materials including carbon fibre infused resin and space grade titanium
to ensure your reel will last for many years.
Plus, all these other
advantages -
Long, accurate casts:
Now, with only the minimum of
practice you will be able to cast
further and more accurately than
ever before.
Control large fish with ease:
Even with the fast recovery this
reel will still control a large fish
with drag pressure & pump and
wind action.
You can fish hard with this reel,
but more care needs to be taken
to avoid too much sand in the
working parts or the reel.
More comfortable fishing:
Low winch-mount rodslet you fish
with your arms in a relaxed
position.
No line twist: Use a small
free-running swivel as the last
piece in any rig and you’ll
minimise any line twist.
Care Instructions
We recommend a thorough
wash in fresh water after use in
salt water.
NOTE: DO NOT USE heavy
grease on gears or exposed
parts inside the back plate as
they will hold sand and cause
excessive wear or malfunction
to your reel.
Reel Icon Pty Ltd Trading as
Alvey Reels Australia ABN 57 625 261 707
2-6 Antimony Street Carole Park Qld 4300
t: [phone] f: [phone]
For more hints and tips on maintenance,
please visit the spare parts page at
www.alvey.com.au
e: [email protected]
#alveyreels
Special Features
→2:1 Gearing
→Super Light Carbon
Fibre Constructed
Spool & Backplate
→Titanium Handle
Plate
→Titanium Spindle
→Titanium Handle
Screw
3
4
5
6
7
89
10
11
12
13
14
15
16
17 18
19
20
21
22
23
24
25
26
27
23,24
24
25
21
1
2
2
4
5
6Special Note - View A
SLIPWASHER

Recommended Line Size
Your 65H reel will hold approximately 650
metres of 9 kg line. If fishing near rocks orother
hazards use heavier line to help avoid line
breakage.
Filling the Spool with Line
Always take the line from the front of the
dispenser, never the side.
Wind firmly and evenly onto the spool,
spreading the line with your fingers to give a
smooth casting base.
Never stretch a nylon monofilament onto a
spool; when it goes back to its original length it
will exert strong enough crushing action to
damage your spool.
Never allow loose coils to develop on your spool
through careless uneven winding.
Adopt the habit of applying light finger tension
when retrieving line and spread evenly over its
bed.
Selecting a Rod
Your rod and reel outfit should be
balanced so you can hold it comfortably
over long periods. A matched set, which
has a point of balance where it’s held in
the left hand, will give you the most
comfortable posture. The ideal rod for
this reel should be 3.3 to 4.4m in length.
The use of a short butt brings the reel into
a natural position for rewinding with your
elbows at your side and without strain.
Rigs & Swivels
When used properly a brass swivel is a very
inexpensive and efficient way to keep a fishing
line in good condition. Curls and twists in a line
can be caused by many things, but can be kept
to a minimum by the correct use of a swivel
Swivel Sizes
Line breaking strain
Swivel size
1 –5 kg
No 14
5 –8 kg
No 12
8 –15 kg
No 10
15 –20 kg
No 9
65H
Light machine oil is better to lubricate the reel
rather than grease which tends to make sand
stick to everything. Flush the reel out in salt
water when fishing to remove excess sand and
when you get home, flush well in a bucket of
water and wind reel when flushing.
To dismantle the reel,loosen the lock nut (Part
24) and slide away from the centre of the reel.
Remove spindle screw and ‘D’ washer (Part 1)
this will allow the spool to be removed from the
back plate.
To replace spool, slide spool back on to main
spindle and slide lock nut (Part 24) back toward
the reel centre until you feel the gears engage.
Lock lightly and tryto wind the handle ofthe reel.
If it is too tight, loosen lock nut slightly and tap
outwards and lock again. Repeat this until the
reel runs smoothly, then lock firmly.
2:1 Winding Ratio
Being a 2:1 winding ratio you will achieve nearly a
metre per turn recovery which is ideal for bait or lure
spinning for pelagic fish such as Mackerel, Tuna, etc.
As with any geared reel, when a load is applied by a
fish to the angler, the pump and wind method for
recovery of line is recommended. (Lift rod then wind
on line as you lower the rod, and then repeat. This
must be done at a rate not to create slack line.)
It should be remembered that fish do not always swim
away from you, quite often a fish will run towards you
to try and shake out the rig; with the high-speed reel
you can still have line pressure on the rig and the fish.
Maintenance
Because your high-speed reel has considerably more
working parts, than your normal Alvey side cast reel,
we do recommend a little more care is taken to keep
sand, particularly out of the reel where possible.
SPECIAL NOTE Refer to view ‘A’ If the reel keeps tightening up and won’t wind freely, then the check that lock nut
(Part 2) has not come loose or the distance between the lock nut and the stainless-steel gear tube & slip washer (Part
11) is too close. There must always be a small amount of clearance between (Part 11) the gear tube and the lock nut.
Make sure both lock nuts are kept tight (Loctite or super glue can be used on the threads to ensure this). The slip
washer must be free moving.
After stripping and cleaning, re-assemble as per the exploded view. Lubricate with light oil where oilcans are shown
and on any moving parts. The main shaft can also be greased or oil down front end of spindle. (Remove Part 1 & 2
to make easier) this should be done regularly.
Clutch washers are a special material, but a lubricant will improve the smoothness of the drag, and these are not affected
by water.
The Simple
method for
LONG DISTANCE
SURF CASTING
With the world’s
best side-cast
reel –ALVEY!
Swivel must be above sinker