ALW H-BEAM 1.25 User manual

A1035 22nd Avenue, Unit 1 nOakland, CA 94606 P510.489.2530 [e-mail] Walwusa.com
INSTALLATION INSTRUCTIONS
H-BEAM 1.25
Wall Mount

HB1.25 Wall Mount Installation Guide 2 of 11 102-000018 - IG110218-A.0
HB1.25 - Safety & Warnings!
1. Read all instructions.
2. Install in accordance with national and local electrical code regulations.
3. This product is intended to be installed and serviced by a qualied, licensed electrician.
4. Do not install in wet locations. For dry and damp use only.
5. Turn off electrical power before installing or servicing xture in any way.
6. To reduce the risk of re and overheating, make sure all connections are tight.
7. This product is suitable for continuous row mounting.
1. Lisez toutes les instructions.
2. Installez conformément à la réglementation du code électrique national et local.
3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualié.
4. Ne pas installer à l’extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec
seulement.
5. Coupez l’alimentation électrique avant de évoluer le système d’éclairage en aucune façon.
6. Pour réduire le risque d’incendie et de surchauffe, assurez-vous que toutes les connexions sont bien
serrées.
7. Peut être monté en rangée continue.
HB1.25 - Attention!
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior
to installation or servicing.

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 3 of 11 102-000018 - IG110218-A.0
Table of Contents
Luminaire Overview
Included Parts
Parts (by others)
Tools Required
Installation
Prepare Wall
Connect Wiring
Joining Straight Sections
Wiring Diagrams
Troubleshooting
Diagram
Traditional On/Off
0-10V Dimming
DMX
DALI
Lutron LDE
4
4
4
4
4
5
5
6
8
10
10
10
10
10
10
11
Mount Fixture 7
Quick Specs 4
Finishing (single-section xtures) 7
Finishing (multi-section xtures) 9

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 4 of 11 102-000018 - IG110218-A.0
Included Parts
3.35"
1.3"
Luminaire Overview
2” x 4” J-Box for wall
applications
Parts (by others)
Drill
#2 phillips bit
Screwdriver
Tools Required
HB1.25 Fixture Mounting Screws
Input Voltage / Frequency:
See product label
Rated Current:
See engineering drawing
Ambient Temperature:
-4° – 120°F (-20° – 50°C)
Environment:
Dry and damp locations
Quick Specs
Level

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 5 of 11 102-000018 - IG110218-A.0
Installation: Prepare Wall
Prepare structure
61⁄8"
111⁄16"
Install 2 x 4 in. J-box into wall (not included). Center of
J-Box should be approximately 6 1/8” from intended end
of xture and 1 11/16” from intended top of xture.
2Install J-box
31⁄8"
Install blocking approximately 3 1/8” from intended end
of xture. See submittal drawings for full mounting dimen-
sions.
1Install blocking

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 6 of 11 102-000018 - IG110218-A.0
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching end
caps.
Installation: Prepare Wall
3⁄16"
Screw mounting screw in until head is approximately
3/16” from wall surface.
5Install mounting screw
31⁄8"
11⁄8"
Install drywall and screw in mounting screws 3 1/8” from
intended end of xture and 1 1/8” from intended top of
xture.
4Install drywall and mounting screws
Make wiring connections between J-Box (from remote
driver) and xture. See submittal drawings and diagrams
on pg. 10 for complete wiring instruction.
6Connect wiring
Installation: Connect Wiring
Install remote driver J-Box(es) in an accessible/
serviceable location. Run low voltage wire from Remote
Driver J-Box to Canopy J-Box in accordance with local/
state/federal regulations.
3Install Remote Driver J-Box

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 7 of 11 102-000018 - IG110218-A.0
9Illuminate xture
Power xture and check for complete illumination
Installation: Finishing (single section xtures)
8Turn power on
Turn power back on at the breaker.
Position keyholes over mounting screws and slide xture
down to ensure proper attachment. If xture does not
slide down, unscrew mounting screw slightly. If xture is
loose on keyhole, tighten mounting screw slightly.
7Mount xture to wall
Installation: Mount Fixture

HB1.25 Wall Mount Installation Guide 8 of 11 102-000018 - IG110218-A.0
11 Connect wiring
Connect wiring quick-connects. It may require two
people to install joining sections.
12 Mount xture to wall
14 Secure internal joiner brackets
Using philips screwdriver, fasten internal brackets. Re-
place heat sink and lens.
Position keyholes over mounting screws and slide xture
down to ensure proper attachment. If xture does not
slide down, unscrew mounting screw slightly. If xture is
loose on keyhole, tighten mounting screw slightly.
Installation: Joining Straight Sections
SHOCK HAZARD! May result in serious injury or
death. Turn power OFF at circuit breaker prior to
installation or servicing.
!
DO NOT PINCH OR PUT EXCESSIVE TENSION ON
WIRES while joining sections or reattaching end
caps.
10 Prepare structure for connecting xture
Install blocking, drywall, and mounting screws as dimen-
sioned in submittal drawings. All mounting points must be
level.
13 Remove lens and heat sink
Carefully remove lens and heat sink to access joiner
brackets.

HB1.25 Wall Mount Installation Guide HB1.25 Wall Mount Installation Guide 9 of 11 102-000018 - IG110218-A.0
16 Illuminate xture
Power xture and check for complete illumination
Installation: Finishing (multi-section xtures)
15 Turn power on
Turn power back on at the breaker.

HB1.25 Wall Mount Installation Guide 10 of 11 102-000018 - IG110218-A.0HB1.25 Wall Mount Installation Guide
Wiring Diagrams
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Ground
Line Voltage (Hot)
Line Voltage (Neutral)
L
N
AC 50/60Hz
Traditional On/Off
Remote LED
Driver J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Grey
Purple
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
0-10VDC (Dim-)
0-10VDC (Dim+)
L
N
AC 50/60Hz
DIM-
DIM+
0-10V Dimming
Remote LED
Driver J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Clear
Black
DMX in shield
DMX in -
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
L
N
AC 50/60Hz
DMX In Shield
DMX in -
Red
DMX in +
DMX in +
Clear
Black
DMX out shield
DMX out -
White
DMX out +
DMX Out Shield
DMX out -
DMX out +
DMX
Remote LED
Driver/Decoder
J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Purple
Grey
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
Data +
Data -
L
N
AC 50/60Hz
DATA +
DATA -
DALI
Remote LED
Driver/Decoder
J-Box
Brown
Blue
Driver 1 LED +
Driver 1 LED -
Yellow
Orange
Driver 2 LED +
Driver 2 LED -
DC
Black
White
Green
Purple
Grey
Line Voltage (Hot)
Line Voltage (Neutral)
Ground
E1
E2
L
N
AC 50/60Hz
E1
E2
Lutron LDE
Remote LED
Driver J-Box

HB1.25 Wall Mount Installation Guide 11 of 11 102-000018 - IG110218-A.0HB1.25 Wall Mount Installation Guide
Troubleshooting
Only a certied electrician can service and troubleshoot product eld issues. Always turn main power off
before servicing xture.
Full Fixture does not illuminate • Ensure xture is wired correctly and power is on.
• Check that circuit breaker is on and not off or tripped.
• Internal LED driver may be defective.
• Ensure no wires are pinched between parts after joining sections or
re-attaching end caps.
Full xture is ickering • 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for
DATA + and - connections. Swapping DATA + and - connections can
cause ickering.
• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase
dimmer is connected to xture. Call tech support for further informa-
tion.
• Possible loose DATA + and - connections from xture to 0-10V, DMX,
or DALI control.
• Possible loose low voltage DC + or - connection from driver to LED.
Call customer support.
Fixture section(s) do not
illuminate
Fixture section(s) are ickering
Fixture does not dim
• Possible loose low voltage DC + or - connection between LED
boards or from LED driver to LED boards.
• Some xtures contain multiple LED drivers. In this case, it’s possible
one of the drivers is defective, which will cause the LED connected
to the driver not to illuminate. Call tech support.
• Ensure no wires are pinched between parts after joining sections or
re-attaching end caps.
• Possible loose low voltage DC + or - connection between LED
boards.
• 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct
for DATA + and - connections. Swapping DATA + and - connections
can cause ickering.
• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase
dimmer is connected to xture. Call tech support for further infor-
mation.
• Possible loose DATA + and - connections from xture to 0-10V, DMX,
or DALI control.