Westinghouse MT25 TILT User manual

ISSUED: 04-16-04 SHEET #: 095-9193-11 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
IMPORTANT! Read entire instruction sheet
before you start installation and assembly.
PART # QTY. DESCRIPTION
A095-4034 1 wall bracket
B095-4140 1 tilt bracket
C504-2013 4 M4 x .7 x 12 mm phillips screw
D520-2005 4 M5 x 10 mm phillips screw
E500-2002 2 #10 X 1 1/2" wood screw
F590-0097 2 concrete anchor
G520-2027 4 M4 x .7 x 10 mm phillips screw
H504-2014 4 M4 x .7 x 20 mm phillips screw
I590-5003 4 retaining spacer
Installation and Assembly - Flat/tilting
wall mount for LCD screen Model: MT25 TILT
A
B
D
FE
Parts List
CHG
MaximumLoadCapacity:
25 lb (11.4 kg)
I
R

ISSUED: 04-16-04 SHEET #: 095-9193-12 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
For Wood Stud Walls use a stud finder to locate center
of stud. Drill two 1/8" (3 mm) dia. holes to a minimum
depth of 1.5" (64 mm). Attach wall bracket (A) to center
of wood stud using two screws (E).
A
E
WOOD
STUD
WALL
Insert two screws (D) into
wall bracket (A).
AD
• Tighten wood screws so that wall plate is firmly
attached,butdonotovertighten.Overtighteningcan
damagethescrews, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderishighlyrecommended.
WARNING

ISSUED: 04-16-04 SHEET #: 095-9193-13 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
For Concrete Walls drill one 1/4" (6 mm) dia. hole to a
minimum depth of 1.5" (64 mm). Insert anchor (F) in hole
flush with wall as shown (right). Place wall bracket (A) over
anchor (F) and secure with #10 x 1.5" wood screw (E). Make
sure wall bracket is level, mark other hole and repeat steps
with other fasteners. Tighten all fasteners.
CUTAWAYVIEW
concrete
wall
3A
F
Drill hole and insert anchor (F)
Place wall bracket (A) over anchor (F) and secure with
screw (E)
After repeating step one tighten all fasteners
F
A
E
• Tighten woodscrewsfirmly, but do notovertighten.
Overtighteningcandamagethescrews,greatly
reducingtheirholdingpower.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
•When installing wall mounts on cinder block, verify that
you have a minimum of 1 5/8" of actual concrete surface
in the 1/4" diameter hole to be used for the concrete
anchors. It is suggested that a standard electric drill on
slow setting is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the hole when
entering a void or cavity. Do not drill into mortar joints,
which are brittle and will not provide a stable anchorage!
WARNING
A
E
F
• Neveruseconcreteexpansionanchorsforattachment
of wall plate to concrete walls covered with a layer of
plaster, drywall, or other finishingmaterial.
WARNING
3B
3C

ISSUED: 04-16-04 SHEET #: 095-9193-14 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Hook tilt bracket (B) onto wall bracket (A).
Adjust tilt (15° forward and 5° back) and
secure with two M5 screws (D).
D
SCREEN
This product is designed to accommodate screens with Vesa®compliant hole
pattern. For safe mounting, please make sure that mounting screws turns at least
three complete turns in the screen inserts.
FORVESA75MOUNTINGPATTERN:1.Choose
hole pattern indicated below. 2. Attach tilt bracket
(B) to back of screen using four 10 mm screws
(G) as indicated below. 3. If hole pattern is in a
pocket, attach tilt bracket (B) to back of screen
using four 20 mm screws (H) and four retaining
spacers (I) as indicated below.
FORVESA100MOUNTINGPATTERN:1.Choose
hole pattern indicated below. 2. Attach tilt bracket (B)
to back of screen using four 10 mm screws (G) as
indicated below. Note: If you don't get three complete
turns in the screen inserts, use four M4 x 12 mm
screws (C) instead of four M4 x 10 mm screws (G).
Note: Screen may appear
slightlydifferentthan
illustrated
For screens with a hole
pattern in a pocket,
spacers (I) go between tilt
bracket (B) and screen.
B
B
• The screen and bracket may be too heavy and bulky for
one person to handle safely. Two or more persons, or
mechanical lifting equipment, should always be used to
securely attach the screen to the wall bracket. Refer to
your screen’s owner’s manual for additional installation
instructions.
WARNING
Note: Refer to your TV owner’s manual for additional instructions which may pertain to the positioning of your
specific TV.
BA
SCREEN

ISSUED: 04-16-04 SHEET #: 095-9193-15 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”)thattheProduct will be free from defectsinmaterial and workmanship, under normal use, foraperiod of five (5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital
Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
daysfrom the date of delivery to the end-user, whichever occurs last.
OBTAINING WARRANTY SERVICE –Toobtainwarrantyservices,youmust either personally deliver orship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at [phone] to
obtainaReturnMerchandiseAuthorization(“RMA”)andforotherinstructionsregardingreturnandreplacementorrepairof
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO WARRANTY –Thiswarrantydoesnotcoverdamagecaused by (a) service or repairsbyanyoneother
thanpersonnelauthorized by Westinghouse Digital Electronics, (b)the failure to utilize proper packingwhenreturning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transitor otherwise.
PROOF OR ORIGINAL PURCHASE –Asales receipt, invoice, or other proof of purchase specifying the original date of
purchasewithin the five (5) year warranty period must be presented to obtain warrantyservice. This warranty extendsto
theoriginal purchaser and is not transferable.
EITHER REPAIR OR REPLACEMENT ISYOUR EXCLUSIVE REMEDY UNDERTHIS WARRANTY. EXCEPTTO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIALDAMAGES CLAIMEDTOARISEFROMBREACHOFANYEXPRESSORIMPLIEDWARRANTYON
THISPRODUCT. ANYIMPLIED WARRANTYOFMERCHANTABILITYOR FITNESS FORAPARTICULARPURPOSE
ONTHISPRODUCTIS LIMITED IN DURATIONANDSCOPETOTHETERMS OFTHISWARRANTY.
Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how
longan implied warranty lasts,so the above limitation may not applyto you. This warranty givesspecific legal rights, and
you may also have other rights which vary from State to State.
WestinghouseDigital Electronics, LLC
16257East GaleAve.
City of Industry, California 91745
Tel: [phone].
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.