Amada Homefurnishing Floating Shelf AMFS01 User manual

Floating Shelf Instruction Manual V1.0
Thank you for choosing this AMADA product! At AMADA we strive to provide you
with the best quality products and services in the industry. Should you have any
issues, please don't hesitate to contact us at [email protected].
Model: AMFS01/AMFS04
• Check package contents against supplied parts and hardware list to assure that all
components were received undamaged. Do not use damaged or defective parts. lf you
require replacement parts, please contact amada customer service at
[email protected].
• Carefully read all instructions before attempting installation. If you do not understand the
instructions or have any concerns or questions, please contact customer service at
[email protected].
• Not all parts and hardware included will be used.
• Using with caution because this product may contain moving parts.
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use. Thank you for your understanding.
IMPORTANT SAFTY INFORMATION

1
Tools Needed (Not lncluded)
Stud Finder Pencil Screwdriver
Supplied Parts and Hardware List
Long Lag Screw
M4x50mm
x4
A
Short Lag Screw
M4x30mm
x4
B
x4
03
Screws
x2
01
Metal Frame
with Shelf
x1
02
Towel Rack
Level
• This shelving system is for designed for use in wood stud, dry wall, solid concrete, and
concrete block walls.
• For drywall mounting, please use wall anchors [C].
• For wood stud mounting, wall anchors [C] and [D] are not necessary.
• For concrete concrete or concrete blocks wall mounting, please use wall anchors [D]
NOTE:
Drill 5/64 in.(2mm)
Wood Drill
15/64 in.(6mm)
Concrete Drill
Wall Anchor
M13x40mm
x4
C
CAUTION!
These wall anchors
are for drywall ONLY.
DO NOT use them in
concrete / brick / wood
studs wall.
CAUTION!
These anchors are for
concrete or brick
walls ONLY. DO NOT
use them in drywall
or wood stud wall.
x4
D
Wall Anchor
ø6mmx4mmx30mm

2
Use a stud finder(not included) to loacte wood studs. Mark the edge and center
locations.
Step 2 Secure Metal Frame with Shelf to Wall
Before installation, please identify your wall type.
For wood stud installation, follow the step 2A.
For drywall installation, follow the step 2B.
For solid concrete and concrete block walls installation, follow the step 2C
Step 2A For Wood Stud
Step 1 Secure the Tower Rack [02] to the Shelf on the Mental Frame [01]
01
02
03
Secure the tower rack [02] to
bottom of the shelf using four
short screws [03].
16 in.
(406mm)

Install the metal frame with shelf using lag screws [A]/[B]. Tighten all lag screws [A]/[B]
with the screwdriver (not included). If you feel it is difficult to install the long lag screws
[A] to wall, you can simply use a 2mm(5/64 in.) drill bit to drill 2 pilot holes for the long
lag screw [A]. Tighten the lag screws [A]/[B] only until the lag screws [A]/[B] are pullled
firmly against the metal frame.
Position the metal frame with shelf at your desired height and line up the holes with
your stud center line. Level the shelf and mark the holes.
3
X
For wood stud mounting,
wall anchors [C] and [D]
are not necessary.
WARNING: X
[Not Included]
[Optional]
A/B
ø5/64 in.(ø2mm)
1.2 in.(30mm)
For Short Lag Screw
2 in.(50mm)
For Long Lag Screw
ø5/64 in.(ø2mm)

Position the metal frame with shelf [01] at your desired height and make sure the metal
frame with shelf [01] is level and flush to the dry wall. Mark the holes for the wall
anchors [C].
Press and screw wall anchors [C] into the drywall using a screwdriver and turn
clockwise. Make sure that wall anchors [C] are flush with the wall.
Install the metal frame with shelf [01] using short lag screws [B] and wall anchors
[C], tighten short lag screws [B] until they are pulled firmly against the metal fame.
4
Step 2B For Drywall
C
B

Position the metal frame with shelf [01] at your desired height and make sure the metal
frame with shelf [01] is level and flush to the solid concrete and concrete block walls.
Mark the holes for the wall anchors [D].
5
Step 2C For Solid Concrete and Concrete Block Walls
Drill 2 pilot holes using a 15/64 in.(6mm) diameter drill bit. Make sure the depth is not
less than 1.4 in.(35mm). Never drill into the mortar between blocks.
1.4 in.(35mm)
For Short Lag Screw
ø15/64 in.(ø6mm)

6
Use the hammer to knock wall anchors [D] into the wall. Be sure the anchors [D] are
seated flush with the concrete surface.
D
Install the metal frame with shelf [01] using short lag screws [B] and wall anchors [D],
tighten short lag screws [B] until they are pulled firmly against the metal fame.
B

Thank you for choosing this AMADA product! At AMADA we
strive to provide you with the best quality products and services
in the industry. Should you have any issues, please don't
hesitate to contact us at [email protected].
Thank you again
for choosing this AMADA product!