Amana ASD2622HRW User manual

@ B
ra|o
Important Safety Instructions ............... 1=2
Installation ............................... 3=7
0
0
0
0
Temperature Controls ...................... 8=9
Fresh Food Features ..................... 10=12
Freezer Features ........................ 13=14
ice and Water .......................... 15=17
Water Filter ............................. 18=20
Food Storage Tips ....................... 21=23
Care and Cleaning ...................... 24=27
Operating Sounds .......................... 28
Troubleshooting ......................... 29=32
Warranty & Service ......................... 33
Guide d'utilisation et d'entretien ............. 34
Guia de use ycuidado ...................... 70
Form No. A/0z/06 Par[ No. z2842128 www.alnana.eeln Li[ho U.S.A. c200G Nlayta_ Appliances Sales Co.

Jmportent$efetyInstructions
Instafler: Please leave this guide wltil ths apphance.
Consumer: Please read and keep thB Use and
Care Guide for future reference; it provides the
proper use and maintenance mformat_on.
Keep sales receipt and/or canceled check as proof
of purchase.
Call 1-800-688-9900 U.S.A.
1-800-688-2002 Canada
1-800-688-2080 (U.S. TrY for hearing or
speech impaired)
(Mon.-FrL 8 am-8 pm Eastern Time)
Have complete model and serial number
mdentlflcatlon of your refngerator. This is located on a
data plate ms,de the fresh food compartment, on the
upper right s,de. Record these numbers below for
easy access.
Model Number
Senal Number
Date of Purchase
In our continuing effort to H_prove tile quahty and
performance of our apphances, it may be necessary
to make changes to the apphance without rewslng
thB guide.
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appeanng Hi
this guide are not meant to cover all possible
conditions and situations that may occur. Common
sense, caLitlon and care must be exercised when
installing, maintaining or operating apphance.
Always contact tile manufacturer about problems or
conditions you do not understand.
DANGER - Immediate hazards whch WILL result
In severe personal injury or death.
To reduce risk of injury or death, follow basic
precautions, including the following:
IMPORTANT: Child entrapment and suffocation
are not problems of tile past. Junked or abandoned
refngerators are st_ll dangerous -even mfthey s_t out
for "just a few days:' If you are getting nd of your old
refrigerator, please follow the instructions below to
help prevent accidents. /_ _-
J
Before you throw away your old _'
refrigerator or freezer: I,,,,',,i,,,'
•Take off the doors.
_',',
• Leave tile shelves in place so _,",,i',,',
children may not easily chmb _',,:,,
Inside. _ _':_--J
This apphance is equipped with a three-prong
grounding plug for your protection against possible
electrical shock hazards. It must be plugged into a
grounding receptacle. Where a standard two-prong
wall receptacle is encountered, it is the personal
responsibihty and obhgation of the customer to have it
replaced with a properly grounded three-prong wall
receptacle. Do not under any c_rcumstances, cut or
remove the third (ground) prong from the power cord.
Do not use an adapter plug.
Power supply cord with
three-prong grounding plug
Recognize Safety Symbols, Words,
Labels
WARNING - Hazards or unsafe practices which
COULD result m severe personal mnjuryor death.
OALFI'ION - Hazards or unsafe practices whch COULD
result in mHlor personal injury or property damage. Grounding type
wall receptacle

Importent$efet¥Instructlons
To reduce risk of {ire, electric shock, serious
injury or death when using your re{rigerator,
follow these basic precautions, including the
following:
1. Read all instructions before using the refngerator.
13.
not attempt service if instructions are not under-
stood or =ftl_ey are beyond personal skill level.
Always disconnect refrigerator from electncaJ
supply before attempting any service. Disconnect
power cord by grasping the plug, no_the cord.
2. Observe all local codes and ordinances.
3. Be sure to follow grounding mstructmons.
4. Check with a quahfled electnc=an _fyou are not
sure this apphance is properly grounded.
5. Do not ground to a gas hne.
6. Do not ground to a cold-water pipe.
7. Refngerator is designed to operate on a separate
115 volt, 15 amp.. 60 cycle Ime.
8. Do not modify plug on power cord. If plug does
not fit electrical outlet, have proper outlet Installed
by a qualified electrician.
9. Do not use a two-prong adapter, extensmon cord
or power strip.
10. Do not remove warning tag from power cord.
11. Do not tamper with refngerator controls.
12. Do not service or replace any part of refrigerator
unless specifically recommended In Use & Care
Guide or pubhshed user-repmr instructions. Do
14.
15.
16.
17.
18.
19.
20.
Install refngerator according to Installation
Instruchons. All connections for water, electrical
power and grounding must comply with local
codes and be made by licensed personnel when
requned.
Keep your refngerator m good condition. Bumping
or dropping refrigerator can damage refngerator
or cause refngerator to malfunction or leak. If
damage occurs, have refrigerator checked by
quahfled service techmclan.
Replace worn power cords and/or loose plugs.
Always read and follow manufacturer's storage
and _deal enwronment instructions for _tems being
stored m refngeratol:
Your refrigerator should not be operated In the
presence of explosive fumes.
Children should not chmb, hang or stand on any
part of the refrigerator.
Clean up spills or water leakage associated with
water installation.
SAVE THESE INSTRUCTIONS

JnstaJJation
Location
• Do not install refrigerator near oven, radiator or other
heat source. If not possible, shield refrigerator with
cabinet material.
• Do not install where temperature falls below 55° F
03 ° C] or rises above 110° F (43° C]. Malfunction
may occur at this temperature.
• Refrigerator is designed for indoor household
application only.
Measuring the Opening
When tnstalling your refrigerator, allow '_" space at top
and '2" space behind n]achlne con]partl]lent cover
(located in the rear) for proper atr circulation. If the
refrigerator is placed with the door hinge side against
a wall, you may want to allow additional space so the
door can be opened wider.
Subfloorlng or floor coverings (i.e. carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gamed by using the leveling
procedure under Leveling.
IMPORTANT: If refrigerator is to be installed into a
recess where the top of the refrigerator is completely
covered, use dimensions fronl floor to top of hinge cap
to verify proper clearance.
Transporting Your Refrigerator
•NEVER transport refrigerator on tts stde. If an
upright position is not possible, lay refrigerator oil its
back. Allow refrigerator to sit upright for
approxtmately 30 minutes before plugging it in to
assure oil returns to the compressor. Plugging
refrigerator m mmledlately may cause damage to
internal parts.
•Use all apphance dolly when moving refrigerator.
ALWAYS truck refrigerator flom its stde or
back-NEVER from its front.
Protect outside finish of refrigerator during transport
by wrapping cabinet m blankets or ulsertlng padding
between the refrigerator and dolly.
Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles when
possible. Do not overtlghten. Overtlghtening
restraints may dent or damage outside finish.
Door and Hinge Removal
Some installations require door removal to get
refrigerator to final location.
To avoid severe personal injury or death, observe the
following:
•Disconnect power to refngerator before remowng
doors. Connect power only after replacing doors.
• Green ground wire must be attached to top hinge
while performing door removal and replacement.
,Tape decoratwe panels (select models] securely
into place before remowng door handles.
To avoid property damage, observe the following:
• Protect vinyl or other flooring with cardboard, rugs
or other protectwe matenal, prior to mowng
refrigerator.
- Do not adjust refrigerator to be any shorter than
68',,)" tall (minus hinge and cap]. Doing so may
damage underside components.
1.
2.
Unplug power cord from power source.
Remove toe grille and bottom bracket covers (see
page 7].
Open both doors 180°, or as wide as possible.
For ice and water dispensing models only:
Remove tile left stde bracket cover by carefully
pulhng the water hne to pn! the covet-loose. Then
continue to maintain downward pressure to the
notched side of the cover while swinging it off
(see page 7].
Note
• For refrtgerators tn operatton, shut off water before
removing water hne from the door.
To Disconnect the Water Line:
•Push In white collar (A] and hold.
•Pull the door-stde tube (B] from the connector.
To Reconnect the Water Line:
• Firmly push tube _'o"into the connector. Use
hnes on the tube as a gutde for full tnsertion.

• If tube end is damaged, cut off _'o"before
recollnectlng.
If leaking occurs, reconnect the line.
3. Close doors.
/4. Remove top hinge covers by
removing Philhps screws.
5. Unscrew %," hex head screws from
top hinges.
For water dispensing
models only:
•Do not renlove screw
connecting green ground
Wlre.
6. For ice and water dispensing models only:
Detach main wire connector harness and red wire
harness.
To detach mare wire
harness, use a flat blade
tool or fingernail to press
jLinCtlOn point between two
connectors to release.
•To detach red wire harness, press
tab on underside of connector to
release.
7. Remove top hinges along with doors.
8. Remove bottom hinges with a ',:' hex head dnver.
Replacing the Doors
•To replace the doors, follow the steps m Door and
Hinge Removal m reverse order.
IMPORTANT: If water hne tube end is damaged, cut
off _o"before reconnecting.
Connecting the Water Supply
(:select models)
To reduce the risk of injury or death, follow
basic precautions, including the following:
• Read all instructions before mstalhng ice maker.
•Do not attempt installation ff instructions are not
Lmderstood or if they are beyond personal skill
level.
. Obsen/e all local codes and ordinances.
• Do not sen/ice ice maker unless specifically
recommended m Use & Care Guide or pubhshed
user-repair instructions.
.Disconnect power to refngerator before mstalhng
ice makeL
• Water damage due to an improper water
connection may cause mold/mildew growth. Clean
up spdls or leakage H_med_ately!
To avoid property damage or possible injury,
follow basic precautions, including the
following:
. Consult a plumber to connect ¼" O.D. copper
tubing to housellold pJumbmg to assure
comphance with local codes and ordinances.
•Verify the copper tubing under the sleeve is smooth
and free from defects. Do not reuse an old sleeve.
•Confirm water pressure to water valve B between
35 and 100 pounds per square inch, 20 pounds
per square inch without filter.
. Do not use a self-piercing, or f.',J'saddle valve. Both
reduce water flow and can become clogged over
time, and may cause leaks if repair is attempted.
oTaghten nuts by hand to prevent cross threading.
FmBh tlghtemng nuts with phers and wrenches.
Do not overhghten.
• Wamttwo to three hours before placing refrigerator
into final position to check and correct any water
leaks. Recheck for leaks after 24 hours.
• Verify the copper tubing under the sleeve is
smooth and free from defects. Do not reuse an
old sleeve.

Materials Needed
'/4"outer diameter flexible copper tubing
Shut-off valve (requires a '/4"hole to be drilled into
water supply line before valve attachment)
•Adjustable wrench
•'/_"hex nut driver
Note
•Add 8' to tubing length needed to reach water
supply for creation of service loop.
1. Create service loop with copper
tubing (minimum 2' diameter).
Avoid kinks in the copper tubing
when bending the service loop.
2. Remove plastic cap from water valve
inlet port.
3. Place brass nut (A) and
sleeve (B) on copper
tube end as illustrated.
(Do not use old sleeve.)
A
4. Place end of copper tubing into water
valve inlet port. Shape tubing slightly. Do
not kink - so that tubing feeds straight
into inlet port.
5. Slide brass nut over sleeve and screw nut
into inlet port. Tighten nut with wrench.
IMPORTANT: Do not overtighten. Cross
threading may occur.
6_ Pull on tubing to confirm connection is
secure. Connect tubing to frame with
water tubing clamp (C) and turn on
water supply. Check for leaks and
correct if necessary. Continue to
observe the water supply connection
for two to three hours prior to moving
the refrigerator to its permanent
location.
7. Monitor water connection for 2/4 hours.
Correct leaks, if necessary.
Handle installation
If not installed, the handle is located in the interior of
the fresh food section or attached to the back of your
refrigerator.
Remove and discard handle packaging and tape.
Handle design varies from refrigerator to refrigerator.
Please reference the appropriate instructions for your
model below.
Front Mount Handle
Materials Needed
•Gloves to protect hands
• Phillips screwdriver
•Plastic door removal card (or '/_2"thick plastic card),
retain the card
To install:
1. The handles are to be oriented
as shown.
Align front mount door handle
clip with the door tabs.
Ensure the handle clips are
positioned slightly above the
door tabs.
/4. Rotate the handle so that the
handle is flat against the door.
5. Push the handle down against the
upper door tab just enough to allow
it to hang unsupported.

6.Alignbottomof handlewithlower
doortab.Pressupperhandleendto
doorsurfaceandfirmlygrasplower
endofhandle.Gentlyslidehandle
upwarduntilbottomofhandlesettles
ondoorsurface,thenreverse
direction,slidingdownwardtoalmost
engagingtabwithclip.
7.Graspthehandlefirmlyandslide
downuntilitclicks.Theaudibleclick
indicatesfasteningclipsaresecurely
interlocked.
To Remove: i
1. Flex the handle away from the door
panel. Simultaneously place door
handle removal card underneath
the base of the lower handle. Insert
the card to the line or until it stops.
2. Grasp the lower part of the handle
firmly and lift to remove.
Handle Extensions [select models]
To install:
1. Align and clip handle extension into position on the
handle. Press the extension over the door retainers.
To Remove:
1. Slide the extension down and unclip from door
retainer.
Full-Length Aluminum Handles
To install:
1. Release top door trim by removing
Phillips screws from top of fresh food
door and retain screws for later use.
2. Align notches on back of handle with
retaining clips on doors. Insert I__
clips into notches and slide
handle down until it contacts
bottom trim.
3. Replace top door trim and Phillips
sorews.
4. Repeat instructions 1-3 to install
other handle.
To Remove:
1. Release top door trim by removing
Phillips screws from top of fresh food
door and retain screws for later use.
2. Grasp handle firmly with both hands.
Slide handle upward approximately
3/_,,to release.
3. Repeat instructions 1-3 to
remove other handle.
To Reinstall:
1. Repeat in reverse order.

Leveling
To enhance the appearance and maintain performance,
the refrigerator should be level in accordance with the
following instructions.
Note
•Complete any required door reversal, panel
installation and/or a water supply connection,
before leveling.
Materials Needed
*3/8"hex head driver
* Carpenter's level
1. Remove toe grille.
* Grasp firmly and pull bottom
outward to unclip.
2. Remove bottom bracket cover(s).
•Place the eraser end of a pencil or similar blunt
tool in the cover notch.
Notch
Location
Use slight pressure to pry the
cover loose.
Continue to maintain
downward pressure to the
notched side of the cover while
swinging it off.
3. Using hex head driver, turn front adjustment
screws (A) clockwise to raise and counterclockwise
to lower the front of the refrigerator.
i ....
• •
Note ]
•Some models only have adjustment screws "A"
4. Select models also have rear adjustment screws
(B). Using the hex head drivel, turn each of these
adjustment screws (B) to raise or lower the rear of
the refrigerator.
Using the carpenter's level, make sure front of
refrigerator is '/_"(6 ram) or 'f_bubble higher than
back of refrigerator and that the refrigerator is level
from side to side.
If required, correct rocking of refrigerator by
turning rear adjustment screw clockwise to raise
rocking corner. If doors are uneven, do the
following:
Determine which
door needs to be
raised.
Turn front roller
adjustment screw (A)
clockwise to raise
front corner of door.
O
* If one refrigerator door has reached the limit of
its adjustment range and doors are still not level,
raise or lower the opposite door by turning roller
adjustment screw counterclockwise.
* Check with level to verify '/4"tilt to the back for
proper door closure.
* If refrigerator is aligned and stable, replace toe
grille and hinge covers.
7. Replace bracket cover(s).
Position cover into the outer edge of the hinge.
Swing the cover toward the cabinet and snap it
into place.
8. Replace the toe grille.
Note
•For proper reinstallation, ensure the "top" marking
on the interior of the toe grille is oriented correctly.
•Align the toe grille mounting clips with the lower
cabinet slots.
•Push the toe grille firmly until it snaps into place.

TemperatureControls
Dial Temperature Controls
([select models[}
The controls are located at the back left of the
refrigerator corn partment.
Note
•The freezer control turns the cooling system on.
Neither section will cool if freezer control is set to
OFE
Initial Control Settings
After plugging the refrigerator in,
set the controls.
•To adjust the controls, turn the
control knob to the left or right
as desired.
•Set the freezer control on/4.
* Set the refrigerator control on 4.
.Let the refrigerator run at least 8
to 12 hours before adding food.
J
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the
cabinet. This condition will be more noticeable when
you first start the refrigerator, during hot weather and
after excessive or lengthy door openings.
Adjusting the Controls
24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If
so, adjust the control(s) as indicated in the
Temperature Control Guide table below. See page 21
for instructions on checking compartment
temperature.
Except when starting the refrigerator, do not change
either control more than one number at a time.
Allow 24 hours for temperatures to stabilize.
•Changing either control will have some effect on the
temperature of the other compartment.
Temperature Control Guide
Refrigerator too warm Turn the refrigerator control
to next higher number.
Refrigerator too cold Turn the refrigerator control
to next lower number.
Freezer too warm Turn the freezer control to
next higher number.
Freezer too cold Turn the freezer control to
next lower number.
Turn refrigerator OFF Turn the freezer control to
OFR
Note
•Turning freezer control to OFF stops cooling in
both compartments. It does not shut off power to
the refrigerator.

TemperatureControls
Touch Temperature Controls
Cselect models, style varies by model)
The controls are located at the top front of the
refrigerator compartment.
Control
t
Initial Control Settings
After plugging the refrigerator in, set the controls.
•Pressing the_ or pads adjusts the controls to
the desired setting.
•Set the freezer control on 4.
•Set the refrigerator control on 4.
•Let the refrigerator run at least 8 to 12 hours before
adding food.
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the
cabinet. This condition will be more noticeable when
you first start the refrigerator, during hot weather and
after excessive or lengthy door openings.
Adjusting the Controls
24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If
so, adjust the control(s) as indicated in the
Temperature Control Guide table below. See page 21
for instructions on checking compartment
temperature.
•Except when starting the refrigerator, do not change
either control more than one number at a time.
•Allow 24 hours for temperatures to stabilize.
Temperature Control Guide
Refrigerator too warm Set the refrigerator control
to next higher number by
Refrigerator too cold
Freezer too warm
Freezer too cold
Turn refrigerator OFF
Set the refrigerator control
to next lower number by
press ng the pad.
Set the freezer control to
next higher number by
Set the freezer control to
next lower number by
Press the freezer or
refrigerator pad until a
dash "-" appears in the
display.

FreshFoodFemres
Shelves
Your refrigerator has either Spillsaver TM or non-sealed
shelves. Spillsaveff Mshelves have a spill retainer edge
which allows for easier clean up and some are
equipped with the EasyGlide TM slide out feature. To
slide out (select models), grasp the front of the shelf
and pull forward. Push in the shelf to return to the
original position.
To Remove aShelf:
• Slightly tilt up the
front and lift up the
rear of the shelf, then
pull the shelf straight
out.
To Lock the Shelf Into Another Position:
• Tilt up the front edge of the shelf.
• Insert the hooks into the desired frame openings and
let the shelf settle into place.
• Be sure the shelf is securely locked at the rear.
The Crisper Top serves as the lower fresh food shelf.
To Remove the Crisper Top:
• Remove drawers as indicated (see page 12).
• Place hand under the frame to push up the glass. Lift
glass out.
• To install, repeat above instructions in reverse order.
SideGlide TM Shelves [select models)
SideGlide TM Shelves can be <-- --I,
adjusted to create a full-
width shelf, or to slide from
side to side to accommodate
storage needs.
To Remove Shelf Rail
Assembly:
• Lift rail assembly up to remove hooks from frame.
To Install Shelf Rail Assembly:
• Tilt up the front edge of the assembly.
• Insert the hooks into the desired frame openings and
let the rail assembly settle into place.
• Be sure the rail assembly is securely locked into the
frame.
To Install SideGlide TM Shelves for Full-width:
• Tilt up the front edge of the shelf slightly.
• Hook the rear lip of the shelf over one of the rails on
the shelf rail assembly.
• Let the shelf settle into place.
•Install the other SideGlide TM shelf on the same rail of
the shelf assembly.
To Install SideGlide TM Shelves for
Sliding Side to Side:
• Tilt up the front edge of the shelf slightly.
• Hook the rear lip of the shelf over one of the rails on
the shelf rail assembly.
• Let the shelf settle into place.
• Install the other SideGlide TM shelf on the other rail of
the shelf rail assembly.
10

FreshFoodFemres
Door Storage
Beverage Chiller M/NliniChiller TM
(select models)
The Beverage Chiller TM and
MiniChiller TM keep beverages and
other items colder than the rest of the
fresh food compartment. An air inlet
directs air from the freezer into the
chiller(s).
Controls
The chiller control is located on the left
side wall of the fresh food compartment.
Turn the control clockwise for colder
tern peratu re.
To Remove Chiller(s):
•Unload the chiller(s).
•Slide the assembly up and pull straight out.
Note
•If the chiller is installed directly under the dairy
center or a door bucket, the bucket or dairy center
will need to be removed before removing the
chiller.
To Install Chiller(s)
•Align one of the air inlet holes with the hole cut-out
on the door.
•Slide the assembly in and down so that the hooks
are firmly seated on the door liner.
Note
•The chillers will not operate properly if the air
intake hole is not aligned with the control location.
Dairy Center
The Dairy Center provides
convenient door storage for
spreadable items such as butter and
margarine. This compartment can be
moved to several different locations
to accommodate storage needs.
To Remove:
•Slide dairy center up and pull out.
To Install:
•Slide assembly in and down so that the hooks are
firmly seated on the door linen
To Remove Dairy Door:
•Press in sides of dairy door and pull out.
To Install Dairy Door:
•Slide sides of dairy door inside dairy center until
hinge points snap into place.
Adjustable Deep Tilt=Out Door Buckets
(:select models)
The Adjustable Deep Tilt-Out Door Bucket provides
easy access to food items stored in the doon
To Remove Bucket:
•Tilt bucket out.
•Pull straight out of the bracket.
To Install Bucket:
•Tilt the front of the bucket down slightly.
•Slide into bracket and tip upright.
To Move Bucket Frame to Another Location:
•Remove bucket.
•Lift bracket up and pull straight
out.
Place the bracket in a new location.
Door Buckets
Door Buckets can be moved to meet individual
storage needs.
To Remove:
•Lift bucket up and pull straight out.
To Install:
•Place bucket in desired door liner
retainer, push down until bucket stops.
11

FreshFoodFemres
Storage Drawers
Humidity=Controlled Crisper Drawers
The Crisper Drawers provide a higher humidity
environment for fresh fruit and vegetable storage.
Controls
The crisper controls regulate the amount of humidity in
the crisper drawer. Slide control toward the Fruit
setting for produce with outer skins. Slide control
toward the Vegetables setting for leafy produce.
Vegetables • O e • ®Fruit
high low @
Humidity
Controlled
To Remove:
*Pull drawer out to full extension. Tilt up front of
drawer and pull straight out.
To Install:
*Insert drawer into frame rails and push back into
place.
Note
* For best results, keep the crisper drawers tightly
closed.
Temperature=Controlled Drawer
(select models)
This drawer can be used for
storage of miscellaneous items. S cheese _Mo,_aets_
I • Q • ®
/he drawer features a control ,,I / /f----_\,
that regulates the air
temperature in the drawer. Set
the control to Cheese to provide \\_.
normal refrigerator temperature.
Use the Meats setting for meats.
Beverage Organizer TM (select models)
The Beverage Organizer TM
slides out from underneath the
Spillsaver TM stationary shelf. The
Beverage Organize€ _ holds up to
twelve 12-ounce beverage cans.
To Remove:
,, Empty contents of can rack. Pull Beverage Organize€ M
forward to full extension and lift front to release from
shelf rail assembly. Pull straight out to remove.
To Install:
,, Insert drawer into frame rails and push back into
place.
Accessories
Grip Pads (select models)
The Grip Pads prevent objects from
sliding in the door buckets. Grip
Pads are removable and are top-rack
dishwasher safe for easy cleaning.
Covered Storage Bucket
(select models)
The Storage Bucket has a lid and
removable egg tray. When tray is
removed, bucket will accept items
such as a standard egg carton, ice,
etc.
Tall Bottle Retainer/Snugger
(select models)
The Tall Bottle Retainer
prevents tall bottles from
tipping forward. The Retainer
can be placed above any
removable door bucket.
The Snugger attached to the Tall Bottle Retainer keeps
bottles and other containers in place when the door is
opened or closed. Adjust the Snugger by sliding from
side to side.
Egg Tray With Handle
(style may vary/select models)
The Egg Tray with Handle
holds a "dozen-plus" eggs. It
can be removed to carry to a
work area or to be washed.
12

Shelves and Baskets
Fixed Freezer Shelf
.ooo.o
Lift shelf from wall mounting
clips and pull left side of shelf
out of wall mounting holes.
To install Clip-mounted Shelves:
• Place left side of shelf in mounting holes and press
down into wall mounting clips.
Shelves
Shelves can be removed to meet individual storage
needs.
To Remove Shelf:
• Snap right side of shelf up from
cabinet railing and slide to right.
To install Shelf:
•Replace shelf in left side cabinet railing. Snap shelf
into right side cabinet railing.
Baskets and Drawers
Baskets and drawers [style may vary]
slide out for easy access of items in
back.
To Remove:
,, Pull out to its full extension. Lift up front of basket
and remove.
To Instalh
*Slide basket or drawer into cabinet railing. Lift up
front of basket or drawer, and slide to the back of
refrigerator.
ice Storage Bin
The ice Storage Bin is located below the automatic
ice maker.
To Remove:
,, Raise ice maker arm to deactivate ice maker. Lift
front of bin and pull out to its full extension. Lift up
front of bin and remove.
To install:
• Slide bin into railing below ice maker until bin locks
into place. Drop ice maker arm to activate ice maker.
iMPORTANT: Ice bin must be locked in place for
proper ice dispensing. Turn auger driver behind bin
counterclockwise [as shown] to properly align ice bin
with auger driver.
13

Door Storage
Adjustable Door Buckets
Door Buckets can be moved to meet individual
storage needs.
To Remove:
• Lift the door bucket up until it
clears the retainers on the door
liner, then pull the door bucket
straight out.
To install:
•Slide bucket in above desired door liner retainer and
push down until bucket stops.
Fixed Door Bucket (select models)
The Fixed Door Bucket is located in
the upper section of the freezer door.
iMPORTANT: Fixed door bucket is not
adjustable. If bucket is removed, freezer
light will not deactivate when door is
closed.
Tilt=out Door Buckets [select models)
The Tilt-Out Door Bucket provides easy access to
food items stored in the door.
To Remove Bucket:
•Tilt bucket out.
• Pull straight out of the frame.
To Install Bucket:
•Tilt the front of the bucket down slightly.
• Slide into frame and tip upright.
To Move Bucket Frame to Another Location:
•Remove bucket.
• Lift frame up and pull straight
out.
Slide the frame in and down into the new location.
14

15
Automatic ice Maker
(non=dispenser models)
Note
• Energy rating guides that are posted on the
refrigerator at the tmle of purchase do not include
optional ice maker energy usage.
Some models are automatm ice maker ready. The
number of the appropriate ice maker kit is IC10S. The
ktt contains mstallatton instructions and water
connection instructions.
Other models have a factory installed ice maker.
Connect the ice maker to the water supply as
instructed on page 5. Proper water flow and a level
refrigerator are essential for optimal ice maker
performance.
Operating instructions
,Conflml toe bm is m place and toe maker arm is
down.
•ARel freezer section reaches
approximately 0° to 2° F (-18 ° to
-17 ° C), ice maker fills with water
and begins operating. You will have
a complete harvest of ice
approximately every three hours.
•Allow approxmlately 24 hours after installation to
recewe first harvest of me.
Dmcard ice created within first 12 hours of operation
to verify system Is flushed of mq)unties.
•Stop ice production by raising ice maker arm until
click is heard.
,Ice maker wHI remain m the OFF position until arm is
pushed down.
•The first one or two batches will probably contain
undersized and irregular cubes because of air Illthe
supply hne.
•When the ice cubes are ejected it is normal for
several cubes to be joined together at the ends. They
can easily be broken apart. The ice maker will
continue to make ice until the supply of ice cubes
rames the sensor arm, shutting the me maker off.
•Certain sounds may accompany the various cycles of
the ice nlaker. The motor may have ashght hunl, the
cubes will rattle as they fall into an empty storage
pan and the water valve may click or "'buzz"
occasionally.
If the ice is not used frequently, the ice cubes will
become cloudy, shrink, stink together and taste stale.
Empty the ice storage bm periodically and wash it m
lukewarm wateE Be sure to dry the bin thoroughly
before replacing tt.
Beverages and foods should not be placed in the ice
storage bin for quick chllhng. These items can block
the sensor arm, causing the ice maker to
nlalfunctlon.
• Turn off (arm up) the ice maker when the water
supply is to be shut off for several hours.
To Remove the Ice Bin:
,Pull it forward, away from the ice maker. To avoid the
ice maker dumping ice while the bin is removed, turn
the ice maker off by raising the sensor arm.
To Install the Ice Bin:
•Reverse the above procedure. Turn the ice maker on
by lowering the sensor arm.
To avoid personal injury or property damage,
observe the following:
•Do not place fingers or hands on tile automatic ice
making mechanmm while the refrigerator is
plugged m. Thin will help protect you from possible
injury. It will also prevent interference with mowng
parts of the ejector mechanmm and the heating
element that releases the cubes.
• Under certain rare circumstances, ice cubes may
be discolored, usually appeanng with a green-
blumh hue. The cause of thin unusual dmcolorat_on
can be a combination of factors such as certain
charactenstlcs of local waters, household
plumbing and the accumulation of copper salts m
an mactwe water supply ime whmh feeds the Ice
maker. Continued consumption of such discolored
ice cubes may be injurious to heaitll. If such
dmcoloratlon is observed, discard the ice cubes
and contact your dealer to purchase and install a
water line filter.
• Water damage due to H_proper water connection
may cause mold/mildew growth.
• Clean up water and me spills to avoid personal
injury and to prevent mold/mildew growth.

Dispenser Features
(select models)
Main
Dispenser
Pad
FrontFill TM
Button
Removable
Tray
Water Dispenser Operation
Dispenser Light (select models)
A light activates within the dispenser area at full power
when dispensing ice or water with the main dispenser
pad. The light will also illuminate when using the
FrontFilP Button (select models).
Dispenser Pad
The Dispenser Pad is located on the back wall of the
dispensing area. When the dispenser pad is pressed,
the selection chosen on the dispenser control panel
will dispense.
FrontFill TM Button (select models)
The FrontFiW _ Button works independently of the
dispenser controls, providing an up-front alternative to
the dispenser pad for dispensing water. This feature is
convenient for filling large items that will not fit into
the dispenser area (i.e. sport bottles, pitchers, large
pans, coffee pots).
This feature allows added convenience of dispensing
ice and water simultaneously. To use, choose your
preferred ice mode from dispenser control panel. Press
container against dispenser pad while pressing the
Front Fill Button.
Removable Tray
The Removable Tray at the bottom of the dispenser
area is designed to collect small spills and may be
easily removed for cleaning and emptying purposes.
IMPORTANT: Removable tray does not drain. Do not
allow tray to overflow. If it does, remove tray and wipe
up overflow.
Note
During initial use of water dispenser, there will be
a one- to two-minute delay while water tank fills
before water dispenses. Discard first 10-14 glasses
of water after initially connecting refrigerator to
household water supply and after extended
periods of nonuse.
To Use Dispenser Pad:
• Choose water selection from dispenser control panel.
Press sturdy, wide-mouthed container against
dispenser pad. When dispensing crushed ice, hold
container as close to chute as possible to reduce
spraying.
Release pressure on dispenser pad to stop water
dispensing. A small amount of water may continue to
dispense and collect in dispenser tray. Large spills
should be wiped dry.
16

17
Dispenser Control (selectmodels)
(control features vary by model)
o 91p
ice Dispenser Operation
To Dispense ice:
•Select Crushed or Cubes ice mode by pushing
button on dispenser control panel. A green light
above button indicates mode selection.
•Press container against dispenser
pad. When dispensing crushed ice,
hold container as close to chute as
possible to reduce spraying.
Notes
•Mode may not be changed while ice dispenser is
in operation.
• If dispenser (select models) is active for more than
five minutes, an automatic lock out sensor will
shut down power to dispenser area. See Dispenser
Lock for unlocking information.
Dispenser Lock (select models)
o
The Dispenser Lock prevents ice or water
from being dispensed.
To Lock Dispenser:
• Press and hold the Lock button for three seconds. A
green indicator light above button will illuminate
when the dispenser is locked.
To Unlock Dispenser:
•Hold the Lock button for three seconds. The green
indicator light above button will go out.
Water Filter Status indicator Water fiJter
Light (select models) .ok
Change
The Water FiJter Status indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset indicator:
•Press and hold both the Lock and Water
buttons simultaneously for four seconds.
The green filter status indicator light will
flash three times when the function has
successfully reset.
Auto Light (select models)
The Auto Light function activates the
dispenser light at half-power when the Light
Sensor detects that the light levels in room are low.
To Activate Auto Light:
• Press Auto Light button. A green indicator light
above button illuminates when the sensor is active.
To Deactivate Auto Light:
• Press Auto Light button. The green indicator light
will go out.
Note
•The dispenser light will operate when Auto Light is
ON or OFF.
Sabbath Mode (select models)
When activated, the Sabbath Mode deactivates the
control lights while leaving the control operational.
To Activate Sabbath Mode:
• Press and hold the Lock and Auto Light
buttons simultaneously for three to four
seconds. After three to four seconds, the
dispenser lights will turn off.
To Deactivate Sabbath Mode:
Press and hold both the Lock and Auto Light
buttons simultaneously for three to four seconds.
After three to four seconds, the dispenser lights will
activate.
Notes
•Dispenser light will not activate during dispensing
while in this mode.
•If the power fails, the control will remain in
Sabbath Mode when power returns.

Water Filter Removal and
Jr|staJJatiofl {select models)
To avoid serious iIhless or death, do not use
refrigerator where water is unsafe or of unknown
quality without adequate disinfection before or after
use of filter.
After installing a new water Nter, always dispense
water for two minutes before removing the filter for
any reason. Air trapped in system may cause water
and cartridge to eject. Use caution when remowng.
,The bypass cap does not filter water. Be sure to
have replacement cartridge available when filter
change Is required.
• If water fHtrahon system has been allowed to
freeze, replace filter caltndge.
*If system has not been used for several months, or
water has an unpleasant taste or odor, flush
system by dBpensmg water for two to three
minutes. If unpleasant taste or odor persists,
change filter cartridge.
Replacing Water Filter
IMPORTANT: Air trapped in system may cause
water and cartridge to eject. Use caution when
removing.
l. Turn filter counterclockwise until it releases from
filter head.
2. Drain water from filter into sink, and dispose m
normal household trash.
3. Wipe up excess water m filter cover and continue
with In/t/a/Installat!on, steps 2 and/4.
The filter should be changed at least every 12 months.
IMPORTANT: Condition of water and amount used
determines life span of water filter cartridge. If water
use IS high, or if water is of poor quality, replacement
may need to take place more often.
To purchase a replacement water filter cartridge,
contact your dealer or call 1-877-232-6771 U.S.A. or
1-800-688-8/408 Canada.
The dispenser feature may be used without a water
filter cartridge. If you choose this option, replace filter
with blue bypass cap.
Initial Installation
The water filter is located m the upper right hand
corner of the fresh food compartment.
1. Remove blue bypass cap and
retain for later use.
2. Remove sealing label from
end of filter and insert into
filter bead.
3. Rotate gently clockwise until
filter stops. Snap filter cover
closed.
/4. Reduce water spurts by
fluslilng air from system.
Run water continuously for
two minutes tlirough
dispenser until water runs
steady. Dunng initial use,
allow about a one- to two-minute delay in water
dispersal to allow internal water tank to fill.
*Additional flushing may be required m some
houseliolds where water is of poor quahty.
18

System Specification and Performance Data Sheet
Refrigerator Water Filter Cartridge Model UKF8OO1AXX
Specifications
Service Flow Rate (Maximum) .............................................0.78 GPM (2.9 L/rain)
Rated Service Life UKF8001AXX-750 (Maximum) ......750 gallons/2838 liters
Maxim um Operating Temperature .....................................100° F/38 ° C
Minimum Pressure Requirement ........................................35 psi/241 kPA
Minimum Operating Temperature ......................................33° F/1° C
Maximum Operating Pressure .............................................120 psi/ 827 kPA
_ntaPure
1000 Apollo Road
Eagan, Minnesota 55121-2240
651.450.4913
EPA EST #35917-MN-1
Performance Data
Parameter
Chlorine
T&O
Particulate**
100834/B
USEPA
MCL
Standard No. 42: Aesflmtie Effects
Influmrt Inflaent
Challenge Concentration Average
2,0 mg/t, + 10o/u 1,89 mg/t,
at least 10,000 particles/ml
IVlin. Required
Redaction
50%
Effluent
Average IVlaximam
<0.05136364 mg/L 0,06 mg/L
30,583 #/ml 09,000 #/ml
%Redaction
Average IVlinimam
>97.26% 96,84o/o
99.52oD 99,94oD5,700,000 #/ml 85%
Parameter
T.rbidity
Cysts
Asbestos
lead at pH 6.5
lead at pH 9.5
Mercury at pH 0.5
Mercury at pH 9.5
Atrazine
Benzene
Carbofuran
p-Dichlorobenzene
Lindane
Toxaphene
USEPA
MCL
] NTLJ**
99,5oD Reductior
99% Reduction
0,015 rag/L
0,015 mg/L
0.002 mg/L
0.002 mg/L
0.003 mg/L
0.005 mg/L
0,04 mg/L
0.075 mg/L
0.0002 mg/L
0.003 mg/L
Standard No, 53: Health Effects
Irdluent
Challenge Concentration
11 + 1 NTLJ***
Minimum 50,000/L
10_10° fihers/L; fibers >10 microl_letersin length
0.15 mg/L + 10%
0.15 mg/L + 10%
,006 mg/L + 10oD
,006 mg/L + 10oD
0,009 mg/L + 10oD
0,015 mg/L + 10%
0,08 mg/L + 10%
,225 mg/L + 10o/u
0.002 mg/L + 10%
0,015 + 1o%
Inflaent
Average
10,7 NTU
106,500 #/L
155 MF/L
0.153 mg/L
0,150 mg/L
0,006 mg/L
0,006 mg/L
0,009 mg/L
0,014 mg/L
0.081 mg/L
0,208 mg/L
0.002 mg/L
0,015 mg/L
Efgaent
Average IVlaximam
031 NTU ,049 NTU
<1 #/L <1 #/L
<1 MF/L <1 MF/L
<001 mg/L <001 mg/L
<.001 mg/L <001 mg/L
0.0003 mg/L 0,0005 mg/L
0,0008 mg/L 0.0015 mg/L
<0.002 mg/L 0,002 mg/L
0,0006 mg/L 0.0011 mg/L
<0.001 mg/L <0,001 mg/L
<0.0005 mg/L <0.0005 mg/L
0.000 mg/L <0,0001 mg/L
<0.001 mg/L <0,001 mg/L
%Redaction
Average Minimum
9709% 9520%
>99,99% >99.99%
>99,99% >99.99%
>99.35% >99,29o/u
>99.33% >9929%
95,70% 90.91%
86.22% 75,93%
70,99% 75,31%
95,71% 92,14%
98.74o/o 99.40o/u
99,70% 99,74o/u
9812oD 90.50o/u
92.97o/u 91.07o/u
Min. Required
Redaction
0,5 NTU
>99.95%
99%
0.10 mg/L
0.10 mg/L
0,002 mg/L
0,002 mg/L
0,003 mg/L
0,005 mg/L
0,04 mg/L
0.075 mg/L
0,0002 mg/L
0,003 mg/L
* Tested using a flow rate of 0.78 gpm; pressure of 00 psig; pH of Z5
09 ° + 5 ° F (20 <' + 3 ° C)
** Measurenlent in Particles/ml, Particles used were 0.5 -1 microns
*** NTU - Nephelometric Turbidity Units
+ 03; temp, of Tested and certified by NSF Interaatioeal against ANSI/NSE Standards 42 & 53
in models UKF8OO1AXX-750 for the reduction of:
Standard No. 42: Aesthetic Effects Standard No. 53: Health Effects
Taste and Odor Reduction Chemical Reduction Unit
Chlorine Taste & Odor Lead, Atrazine, t,indane, Benzene,
Mechanical Filtration Unit Carbofuran, p-Dichlorobenzene, Mercury
Particulate Reduction Class 1 & Toxaphene Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos Reduction
19
General Use Conditions
Read this Performance Data Sheet and compare the
capabilities of this unit with your actual water treatment
needs.
DO NOT use this product where water is microbiologic-
ally unsafe or of unknown quality without adequate
disinfection before or after the system. System certified
for cyst reduction may be used on disinfected water
that may contain filterable cysts.
USE ONLY WITH COLD WATER SUPPLY. CHECK FOR
COMPLIANCE WITH THE STATEAND LOCAL LAWS
AND REGULATIONS.
The PuriClean_II retractable water filtration system uses a
UKF8001AXX replacement cartridge, Timely replacement of
filter cartridge is essential for performance satisfaction from
this filtration system, Please refer to the applicable section of
your Use & Care Guide for general operation, maintenance
requirements and troubleshooting, Suggested retail price of
replacement water filter is $39,99,
This system has been tested according to ANSI/NSF 42 and
53 for reduction of the substance listed above. The
concentration of the indicated substances in water entering
the system was reduced to a concentration less than or equal
to the permissible limit for water leaving the system, as
specified in ANSI/NSF 42 and 53.