American International GMK422 User manual

©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC.
GMK422 Mounting Kit
TECH Ver. 1/13 PRINT Ver. 1/13
Buick
1997-05 CENTURY
1995-05 LE SABRE
1995-05 PARK AVE
2004-07 RAINIER
1995-04 REGAL
2002-07 RENDEZVOUS
1996-99 RIVIERA
1995-96 ROADMASTER
1996-98 SKYLARK
Cadillac
1990-96 FLEETWOOD
1990-92 BROUGHAM
1992-95 EL DORADO
2003-06 ESCALADE/ESV
1992-95 SEVILLE
Chevrolet
2003-06 AVALANCHE
2002 *BLAZER
2003-05 BLAZER
2000-05 CAVALIER
2004-12 COLORADO
2001-07 EXPRESS VAN
2000-05 IMPALA
2001-03 MALIBU
2004 MALIBU CLASSIC
1998-01 METRO
2000-05 MONTE CARLO
2003-06 SSR
2002 *S-10 P/U
2003-04 S-10 P/U
2003-06 SILVERADO
2007 SILVERADO
Classic
2003-06 SUBURBAN
2003-06 TAHOE
1998-04 TRACKER
2002-09 TRAILBLAZER
2000-05 VENTURE
Geo
1995-97 METRO
GMC
2004-12 CANYON
2002-09 ENVOY
2002-03 *JIMMY
2001-07 SAVANA VAN
2003-06 SIERRA
2007 SIERRA Classic
2002 *SONOMA
2003-04 SONOMA
2003-06 YUKON
2003-06 YUKON XL
Honda
1998-02 PASSPORT
Hummer
2003-06 H1
2003-07 H2/SUT
Isuzu
1998-00 AMIGO
2003-08 ASCENDER
1998-04 RODEO
2006-07 i280
2006-07 i350
2007-09 i290
2007-09 i370
Oldsmobile
1996-98 ACHIEVA
1999-04 ALERO
1995-03 AURORA
1998-04 BRAVADA
1995-99 CUTLASS/SUPREME
1994-99 DELTA 88/ROYALE/88
1998-02 INTRIGUE
1996-99 LSS
1994-96 NINETY-EIGHT
1997-98 REGENCY
2000-04 SILOUETTE
Pontiac
2001-05 AZTEK
2000-05 BONNEVILLE
2001-05 GRAND AM
2000-05 SUNFIRE
2000-04 MONTANA
2003-08 VIBE
Suzuki
2002 AERIO
1992-98 SIDEKICK
1998-02 ESTEEM
1999-02 GRAND VITARA
1995-01 SWIFT
1999-03 VITARA
2001-02 XL-7
Toyota
2003-04 MATRIX
VEHICLE APPLICATIONS *Fits oversized Delco Radio dash opening only

BRACKET PREPARATION
GM-K422
For All Vehicles Not Including
1990-96 Fleetwood/Brougham
Remove the (2) top and the (2) bottom mounting tabs located on the Trim ring
of the GM-K422 kit.
REMOVE
REMOVE
For 1990-1996 Cadillac Fleetwood/Brougham instructions
See page 6
1

FIG. B
**Remove all mounting tabs on the Side Brackets
Suzuki
AERIO
ESTEEM
SIDEKICK
SWIFT
GRAND
VITARA
VITARA
XL-7
Chevy/GEO
METRO
TRACKER
FIG. A
Buick
CENTURY
LA SABRE
PARK AVE
REGAL
REGENCY
RENDEZVOUS
RIVIERA
ROADMASTER
SKYLARK
Cadillac
ESCALADE
Chevrolet
BLAZER
CAVALIER
COLORADO
EXPRESS VAN
IMPALA
MALIBU
MONTE CARLO
S-10 P/U
SILVERADO
SUBURBAN
SSR
TAHOE
VENTURE
GMC
CANYON
ENVOY
JIMMY
SIERRA
YUKON
YUKON XL
Hummer
H2
Isuzu
ASCENDER
i-280 / i-290
i-350 /i-370
Oldsmobile
ACHIEVA
ALERO
AURORA
BRAVADA
CUTLASS/SUPREME
DELTA
88/ROYALE
INTRIGUE
Oldsmobile (Cont.)
LSS
NINETY-EIGHT
SILOUETTE
Pontiac
AZTEK
BONNEVILLE
GRAND AM
MONTANA
SUNFIRE
Attach mounting brackets to radio
components using screws supplied
with kit or radio
Attach trim ring to brackets before
tightening radio mounting brackets
Do not remove these
mounting tabs from
ISO trim ring
SIDE BRACKET PREPARATION
2
**Remove all mounting tabs on the Side Brackets not shown above.
Remove all mounting Tabs on ISO Trim Ring

KIT ASSEMBLY
1992-95 Cadillac Applications
For All Vehicles Not Listed Below
1998-02 Honda Passport
1998-00 Isuzu Amigo
1998-02 Isuzu Rodeo
Insert Cadillac bracket into slots
on left & right mounting brackets
**Remove all mounting tabs on the ISO Trim ring
Remove tabs on both sides of trim ring
Remove All tabs on both sides of mounting brackets.
Using 2 nuts & bolts provided with kit, insert 1 bolt into each
slot of Cadillac bracket facing downward as illustrated below
Attach mounting brackets to radio components
using screws supplied with kit or radio
Attach trim ring to brackets before
tightening radio mounting brackets
KIT ASSEMBLY
Remove all tabs on both
left and right brackets.
3

All Double DIN Applications
DASH DISASSEMBLY INSTRUCTIONS
2003-08 Pontiac Vibe/2003-04 Toyota Matrix
1. Starting from the bottom of the Radio trim bezel, carefully pry outward on
the dash trim bezel to unclip the lower edge and sides.
2. Angle the dash trim bezel outward from the bottom and pull the top of the
panel down to unfasten the two upper tabs.
3. Pull the trim bezel forward and disconnect all harnesses attached to the
panel and remove panel.
4. Remove the harness clamp attached at the rear of the left factory radio bracket.
5. Remove the (4) 10mm bolts securing the factory radio to the sub-dash.
6. Pull radio forward, disconnect the wire harness and antenna lead and remove radio.
**Remove all mounting tabs on the Side Brackets not shown above.
Remove all mounting Tabs on ISO Trim Ring
FIG. D
Pontiac
VIBE
Toyota
MATRIX
Attach mounting brackets to radio
components using screws supplied
with kit or radio
See bracket preparation
for your vehicle
Attach trim ring to brackets before
tightening radio mounting brackets
For kit assembly instructions see Figure E on page 5
4

Honda
PASSPORT
FIG. C
FIG. E
**Remove all mounting tabs on the Side Brackets not shown above.
Remove all mounting Tabs on ISO Trim Ring
DASH DISASSEMBLY INSTRUCTIONS
1998-02 Honda/Isuzu Applications
1. Open ashtray and remove ashtray cup.
2. Remove (1) phillips screw from rear of ashtray cavity.
3. Carefully unclip trim bezel from around radio/lighter assembly.
4. Disconnect wire harness from lighter and remove trim assembly.
5. Remove the (4) phillips screws securing radio to subdash.
6. Pull radio forward, disconnect the wire harness and antenna lead and remove radio.
Cut and remove
top corners
Attach mounting brackets to radio components
using screws supplied with kit or radio
Attach trim ring to brackets before
tightening radio mounting brackets
Izusu
AMIGO
RODEO
5

1. Carefully unclip the dash trim bezel from above the climate controls.
2. Remove the (2) screws securing the top of the Radio/climate control trim bezel,
carefully unclip and remove bezel.
3. Remove the (4) screws securing the radio to the sub-dash.
4. Carefully slide radio out of the dash, disconnect all wire harnesses and antenna lead
(if applicable) and remove radio.
5. Remove the top and bottom mounting brackets from the factory radio; you will need to
attach these brackets to the installation kit following the instructions in the kit.
DASH DISASSEMBLY INSTRUCTIONS
1990-1996 CADILLAC FLEETWOOD / FLEETWOOD BROUGHAM
1. Attach top factory mounting bracket (using carriage bolts and nuts supplied with kit)
to top edge of kit.
2. Attach bottom factory mounting bracket (using carriage bolts and nuts supplied with
kit) to bottom edge of kit.
FACTORY BRACKET ATTACHMENT INSTRUCTIONS
FIG. 2
REMOVE ALL MOUNTING TABS ON THE SIDE BRACKETS.
REMOVE (4) SIDE MOUNTING TABS ON ISO TRIM RING.
Attach ISO mounting brackets to
radio components using screws
supplied with kit or radio
Attach trim ring to brackets
before tightening radio
mounting brackets
GM-K422
View of the Top Edge View of the Bottom Edge
ISO MOUNT INSTRUCTIONS
6

CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales [phone]
Canada Sales [phone] • USA Fax [phone]
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
iGMK422