American International LXSK1315 User manual

Fig. B
For ISO mount only: Attach (1) ISO Spac r to th
insid of upp r s ctions on both L ft & Right
mounting brack ts as shown in Fig. A.
NOTE: ISO trim ring (DITR-1315) must b us d in plac of aft r-mark t radio’s trim rings. For ISO mount
applications, mount aft r-mark t radio compon nts to sid brack ts using scr ws provid d with radio
wh n possibl or hardwar includ d with kit optional.
ITR-1315
(Top)
Cut
Cut
L ft
Right
Fig. A R mov shad d tab on l ft
and right brack t
(Right tab hidd n
in pictur )
Doubl DIN Mount Applications
1. R mov th Shad d tab from th bottom of ach l ft and right mounting brack t (s Fig. B b low).
2. Cut and r mov c nt r rib from main brack t.
3. Attach th l ft and right sid brack ts to th main brack t.
4. Attach climat controls to th top of th kit using factory scr ws.
5. Follow st ps 5-7 from singl ISO instructions on pag 3.
6. Attach a r ar support brack t to th r ar of th radio compon nts and adjust as n d d to allow r ar support
brack t to r st in th sub-dash.
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
LXSK1315 Mounting Kit
L xus
1998-05 GS 300 (w/out Factory Navigation)
1998-03 GS 400
2001-05 GS 430
VEHICLE APPLICATIONS
KIT ASSEMBLY INSTRUCTIONS
©2015 AME ICAN INTE NATIONAL INDUST IES, INC. TECH Ver. 5/14 P INT Ver. 5/15
DITR-1315

1. Carefully unsnap and pull forward the vent/clock assembly from above
the factory radio.
2. Unplug the wire harnesses from the rear of the vent/clock assembly and
remove assembly.
3. emove the (2) 10mm bolts securing the upper radio/climate control brackets to
the sub-dash.
4. Carefully remove the ashtray assembly from below the climate controls.
5. emove the (2) 10mm bolts securing the lower radio/climate control brackets to
the sub-dash.
6. Carefully pull radio/climate control assembly forward, disconnect all wire
harnesses and antenna lead wire from radio and climate controls and
remove entire assembly.
7. emove the factory climate control unit from the factory brackets.
Singl ISO Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket into lower section of the main bracket.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach climate controls to the top of the kit using factory screws.
5. Attach (1) ISO Spacer to the inside of upper section on both Left & ight mounting
brackets as shown in Fig. A.
6. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
7. Slide radio components forward or backward for desired look and tighten screws.
8. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
Singl DIN Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket into lower section of the main bracket.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
NOTE: ISO trim ring (ITR-1315) may b us d in plac of aft r-mark t radio’s trim rings.
ITR-1315
(Top)
For ISO mount only: Attach (1) ISO
Spac r to th insid of upp r s ction on
both L ft & Right mounting brack ts
as shown in Fig. A.
L ft
Right
Fig. A
DASH DISASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS
KIT ASSEMBLY INSTRUCTIONS
2 3