American International TOYK994 User manual

Toyota
2006-12 RAV 4
VEHICLE APPLICATIONS
TOYK994 Mounting Kit
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 1/13 PRINT Ver. 1/15

2
Fig. D
Clip
R
NOTE: ISO trim ring (ITR994) may be used in
place of after-market radio’s removable trim ring.
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B opposite page.
2. Insert pocket (part # POC994) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new
radio into the upper section of the
installation kit.
5. Depress the tabs from inside the
sleeves opening upward, outward,
and downward to secure sleeve to
the installation kit.
6. Install radio into sleeve and lock
into place.
7. Attach a rear support bracket to
the rear of the new radio and
adjust as necessary to attach
to the rear support stud located
on the back of the pocket
using the small phillips screw
supplied with kit (optional).
KIT ASSEMBLY INSTRUCTIONS
1. Starting from the bottom edges, carefully pry outward the trim panels from the left and
right sides of the radio and climate controls, disconnect the attached harnesses and
remove trim panels.
2. Remove the (4) 10mm bolts securing the radio to the sub-dash.
3. Pull radio forward, disconnect all harnesses and antenna lead from radio and
remove radio.
1. Using the (4) small phillips screws attach the kits upper sub-dash support arms to the
Left and Right location as shown in Fig. D.
2. Slide on and attach one of the metal clips to each sub-dash support arm.
DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS
2006-2012 TOYOTA RAV 4
Main Frame
DIN Sleeve
L

Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B.
2. Insert pocket (part # POC994) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. A. (See note #2 below)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (optional).
KIT ASSEMBLY INSTRUCTIONS
3
NOTE: #1 - ISO trim ring (ITR994) may be used in place of after-market radio’s removable trim ring.
#2 - Spacers must read upright (This side up for single ISO install).
ITR994
(Top)
For ISO mount only: Attach (1) ISO
Spacer to the inside of upper section (See
note #2) on both Left & Right mounting
brackets as shown in Fig. A.
Left
POC994
IMB994L
IMB994R
Right
Fig. A
Fig. B
Main Frame

Double DIN Mount Applications
NOTE: Remove shaded pocket support Tabs on left and right bracket (See Fig. C below).
1. Cut and remove center rib from main frame and file edges smooth.
2. Attach the left and right side brackets to the main frame (See figure C below).
3. Attach (1) ISO Spacer to the inside of upper section on both Left & Right
mounting brackets as shown in Fig. A. (See note #2 below).
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
5. Slide radio component forward or backward for desired look and tighten screws.
6. Attach a rear support bracket to the rear of the radio components and adjust
as needed to allow rear support bracket to rest in the sub-dash (optional).
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
KIT ASSEMBLY INSTRUCTIONS
NOTE: #1 - ISO trim ring (DITR994) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
#2 - Spacers must read upright (This side up for DBL ISO install).
For ISO mount only: Attach (1) ISO Spacer to the
inside of upper sections (See note #2) on both Left
& Right mounting brackets as shown in Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR994
IMB994L
IMB994R
Fig. C
Main Frame
iTOYK994
Remove shaded pocket
support Tabs on left
and right bracket.