American International TOY-K985 User manual

Double DIN & Double ISO Mount Applications
1. emove the shaded tab from the bottom of each left and right mounting bracket. See fig. C illustration below.
2. Attach the left and right side brackets to the main frame. See figure C below.
3. Cut and remove the center rib from the main frame and file edges smooth.
4. Follow steps 4-6 from single ISO instructions on page 3. (See note #2 below)
5. Attach a rear support bracket to the rear of the radio components and adjust as needed
to allow rear support bracket to rest in the sub-dash.
6. Attach the vent trim assembly (removed in step 7 of dash disassembly on page 2)
to the rear of the installation kit.
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
Toyota
2011-12 SIENNA
VEHICLE APPLICATIONS
KIT ASSEMBL INSTRUCTIONS
NOTE: #1 - ISO trim ring (DIT -985) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
For ISO mount only: Attach (1) ISO Spacer to the
inside of upper sections of the Left & ight
mounting brackets as shown in Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR-985
IMB-985L
IMB-985R
Fig. C
Main Frame
TOY-K985 Mounting Kit
iT YK985
EMOVE SHADED
POCKET SUPPO T TABS
(Both L& mounting brackets)
©2012 AMERICAN INTERNATI NAL INDUSTRIES, INC. TECH Ver. 6/12 PRINT Ver. 5/11

Single DIN Mount Applications
1. Attach the left and right side brackets
to the main bracket.
See Figure B opposite page.
2. Insert pocket (part # P C-985)
into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the
sleeves opening upward, outward,
and downward to secure sleeve to
the installation kit.
6. Install radio into sleeve
and lock into place.
7. Attach a rear support bracket to the
rear of the new radio and adjust as
necessary to attach to the rear support
stud locate on the back of the pocket
using the small phillips screw
supplied with kit.
8. Attach the vent trim assembly
(removed in step 7 of dash
disassembly above) to the
rear of the installation kit.
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B.
2. Insert pocket (part # P C-985) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) IS Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. A. (See note #2 below)
5. Insert IS mountable radio between IS mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach the vent trim assembly (removed in step 7 of dash disassembly on page 2)
to the rear of the installation kit.
KIT ASSEMBL INSTRUCTIONS
2 3
NOTE: #1 - ISO trim ring (IT -985) may be used in place of after-market radio’s removable trim ring.
ITR-985
(Top)
For ISO mount only: Attach (1) ISO
Spacer to the inside of upper sections of
the Left & ight mounting brackets as
shown in Fig. A.
Left
POC-985
IMB-985L IMB-985R
Right
Fig. A
Fig. B
Main Frame
NOTE: ISO trim ring (IT -985) may be used in
place of after-market radio’s removable trim ring.
KIT ASSEMBL INSTRUCTIONS
1. Carefully unclip and remove the trim panel that stretches from above the glove box
to below the Climate Control module.
2. Unscrew and remove the Shifter knob.
3. Carefully unclip and remove the shifter trim panel.
4. Unclip the Climate Control module, and rest out of the way.
5. Remove the (4) 10 MM bolts securing the radio to the sub-dash.
6. Carefully pull the Radio/Vent assembly forward, disconnect all attached harnesses
and antenna lead and remove Radio/Vent assembly.
7. Remove the (4) Phillips screws securing the Vent trim assembly to the radio and set
aside the trim to be attached to the installation kit.
1. Remove the factory radio (upper side)
mounting brackets, as shown in
Fig. D below, and attach to the rear side
of the T Y-K985 main bezel using the
screws from the factory radio.
DASH DISASSEMBL AND RADIO REMOVAL INSTRUCTIONS
2011 TO OTA SIENNA
Main Frame
DIN Sleeve
Fig. D