American Megatrends MI956 User manual

MI956
Intel®Sandy Bridge / PCH
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0
All manuals and user guides at all-guides.com
all-guides.com

ii MI956 User’s Manual
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® Sandy Bridge DC Mobile Processor are registered
trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics Corporation.
All other product names or trademarks are properties of their
respective owners.
All manuals and user guides at all-guides.com

MI956 User’s Manual iii
Table of Contents
Introduction.......................................................1
Product Description............................................................. 1
Checklist..............................................................................2
MI956 Specifications ..........................................................3
Board Dimensions...............................................................5
Installations.......................................................6
Installing the CPU ............................................................... 7
Installing the Memory .........................................................8
Setting the Jumpers .............................................................9
Connectors on MI956........................................................13
BIOS Setup.......................................................22
Drivers Installation......................................51
Intel Chipset Software Installation Utility......................... 52
VGA Drivers Installation ..................................................53
Realtek HD Audio Driver Installation............................... 54
LAN Drivers Installation...................................................55
Intel® Management Engine Interface ............................... 57
ASMedia USB 3.0 Drivers................................................ 59
Appendix...........................................................60
A. I/O Port Address Map................................................... 60
B. Interrupt Request Lines (IRQ)......................................61
C. Watchdog Timer Configuration.................................... 62
All manuals and user guides at all-guides.com

iv MI956 User’s Manual
This page is intentionally left blank.
All manuals and user guides at all-guides.com

INTRODUCTION
MI956 User’s Manual 1
Introduction
Product Description
The MI956F Mini ITX motherboard is based on the latest Intel® QM67
chipset. The platform supports 2nd generation Intel® Core processor
family with rPGA988B packing and features an integrated dual-channel
DDR3 memory controller as well as a graphics core.
The latest Intel® processors provide advanced performance in both
computing and graphics quality. This meets the requirement of
customers in the gaming, POS, digital signage and server market
segment.
The Intel® QM67 is made with 32 nanometer technology that supports
Intel’s first processor architecture to unite the CPU and the graphics core
on the transistor level. The MI956F Mini ITX board utilizes the
dramatic increase in performance provided by this Intel’s latest
cutting-edge technology. Measuring 170mm x 170mm, MI956F offers
fast 6Gbps SATA support (2 ports), USB3.0 (2 ports) and interfaces for
DVI-D, DVI-I, LVDS and HDMI displays. MI956AF features Intel
Active Management Technology 7.0.
MI956F FEATURES:
 Supports Intel® 2nd Generation Core i7/i5/i3 QC/DC mobile
processors
 Two DDR3 SoDIMM, 1066/1333MHz, Max. 16GB memory
 Dual Intel® PCI-Express Gigabit LAN
 Integrated Graphics for DVI-I, DVI-D/HDMI/LVDS displays
 4x SATA 2.0, 2x SATA 3.0, 8x USB 2.0, USB 3.0 (2 ports),
4x COM, Watchdog timer
 1x PCI-E (x16), 1x Mini PCI-E
 Optional AMT (MI956AF only)
All manuals and user guides at all-guides.com

INTRODUCTION
2 MI956 User’s Manual
Checklist
Your MI956 package should include the items listed below.
 The MI956 Mini-ITX motherboard
 This User’s Manual
 1 CD containing chipset drivers and flash memory utility
 Serial ATA cable
All manuals and user guides at all-guides.com
all-guides.com

INTRODUCTION
MI956 User’s Manual 3
MI956 Specifications
Product Name MI956AF/MI956F
Form Factor Mini-ITX
CPU Type - Intel® 2nd generation CoreTM i7/i5/i3 QC/DC mobile processor
- rPGA package, 37.5 x 37.5 mm
- TDP: QC = 45W~ 55W/ DC = 35W
**Sandy Bridge CPU is NOT socket compatible with Arrandale
CPU Speed Up to 2.7GHz
Cache Up to 8MB
CPU Socket rPGA 988B
Chipset Intel® QM67 PCH; 25 x 27 mm package size
BIOS AMI BIOS, support ACPI Function
Memory Intel® 2nd generation CoreTM i7/i5/i3 QC/DC mobile processor integrated memory
controller
DDRIII 1067/1333 MHz
- SO-DIMM x 2 (w/o ECC), Max. 16GB
VGA - Intel® 2nd generation CoreTM i7/i5/i3 mobile processor integrated Gfx
 DVI-I X 1 (thru Level shifter ASM1442)
 DVI-D X 1 (thru Level shifter ASM1442)
 HDMI X 1 (thru Level shifter ASM1442)
 LVDS : DF13 x 2 for supporting dual channel 24-bit
LAN 1. Intel® Lewisville 82579LM GbE PHY[MI956AF only]
or 82579V GbE PHY [MI956F only]
2. Intel® 82583V as 2nd GbE
USB USB 2.0 host controller, supports 8 ports w/ two EHCI, 7 U HCI controllers
Integrated USB 2.0 Rate Matching Hub.
- 4 ports in the rear panel
- Others reserved for onboard pin header ( 4 ports, 2.54mm pitch)
USB 3.0 host controller [ASMedia # ASM1042], support 2 ports
- 2 ports in the rear panel
Serial ATA Intel® QM67 PCH built-in SATA controller, supports total 6 ports
2 x SATA (3.0) 6Gbps+ 4 x SATA (2.0) 3Gbps ports (2 FIS based Port Multiplier)
Audio Intel® QM67 PCH built-in High Definition Audio controller+ ALC892 w/ 7.1 CH
LPC I/O Fintek F81865-I (Ver. C)
COM1 (RS232/422/485), COM2/COM3/COM4 (RS232), Hardware
Monitor (2 thermal inputs,4 voltage monitor inputs & 2 fan headers) [CPU FAN
controllabl, but not the system fan]
COM1/2 with pin-9 with power for 2 ports (500 mA for each port)
Digital IO 4 in & 4 out
IAMT(7.0) Intel® QM67 PCH built-in (MI956AF only)
- Intel® Active Management Technology ver. 7.0
Expansion
Slots - PCI-Express (16x) *1 [PEG]
- Mini PCI-Express (1x) *1 @ Solder side
[Reserved mounting holes for Half-sized also]
Edge
Connector: DVI-D + DVI-I stack connector; Dual DB9 stack connector for COM #1, #2
Dual USB(3.0) dual stack connector; HDMI stack connector
Gbit LAN RJ-45 + dual USB(2.0) stack connector x2
RCA Jack 3x1 for HD Audio
Onboard
Header/
Connector
2 ports x SATA III [Blue color]; 4 ports x SATA II
2x5 pin-header x2 for 4 ports USB; 2x5 pin-header for front panel audio
2x10 pin-header for COM3 (RS232) & COM4 (RS232)
2x5 pin-header for Digital IO; 4-pin box header for LCD backlight control
Watchdog Timer Yes (256 segments, 0, 1, 2…255 sec/min)
System
Voltage ATX
Others LAN Wakeup, EuP/ErP feature (Fintek F75160), UL 60950-1 2nd Edition
compatible
All manuals and user guides at all-guides.com

INTRODUCTION
4 MI956 User’s Manual
Board Size 170mm x 170mm
All manuals and user guides at all-guides.com

INTRODUCTION
MI956 User’s Manual 5
[
Board Dimensions
All manuals and user guides at all-guides.com

INSTALLATIONS
6 MI956 User’s Manual
Installations
This section provides information on how t o use t he jumpers and
connectors on the MI956 in order t o set up a workabl e system. The
topics covered are:
Installing the CPU.................................................................................. 7
Installing the Memory............................................................................ 8
Setting the Jumpers................................................................................ 9
Connectors on MI956 .......................................................................... 13
All manuals and user guides at all-guides.com

INSTALLATIONS
MI956 User’s Manual 7
Installing the CPU
The MI956 board supports rPGA988B socket for Intel® Sandy Bridge
Dual Core mobile processors.
The processor socket com es with a screw to secure the processor. As
shown in the left picture below, loosen the screw first before inserting
the processor. Place the processor in to the socket by m aking sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slide into the socket, fasten the
screw. Refer to the figures below.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
All manuals and user guides at all-guides.com
all-guides.com

INSTALLATIONS
8 MI956 User’s Manual
Installing the Memory
The MI956 board supports two DDR3 memory socket for a maximum
total memory of 16GB in DDR3 SO-DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
DDR3 Module
Lock Lock
Lock Lock
All manuals and user guides at all-guides.com

INSTALLATIONS
MI956 User’s Manual 9
Setting the Jumpers
Jumpers are used on MI956 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI956 and their respective functions.
Jumper Locations on MI956................................................................ 10
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection .................... 11
JP5: COM1 RS232 RI/+5V/+12V Power Setting ............................... 11
JP6: COM2 RS232 RI/+5V/+12V Power Setting ............................... 11
J10: LCD Panel Power Selection......................................................... 12
J14: Flash Descriptor Security Overide (Factory use only)................. 12
J22: Clear ME Contents....................................................................... 12
J23: Clear CMOS Contents ................................................................. 12
All manuals and user guides at all-guides.com

INSTALLATIONS
10 MI956 User’s Manual
Jumper Locations on MI956
Jumpers on MI956 ........................................................................... Page
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection..................... 11
JP5: COM1 RS232 RI/+5V/+12V Power Setting................................ 11
JP6: COM2 RS232 RI/+5V/+12V Power Setting................................ 11
J10: LCD Panel Power Selection......................................................... 12
J14: Flash Descriptor Security Overide (Factory use only)................. 12
J22: Clear ME Contents....................................................................... 12
J23: Clear CMOS Contents.................................................................. 12
All manuals and user guides at all-guides.com

INSTALLATIONS
MI956 User’s Manual 11
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection
COM1
Function RS-232 RS-422 RS-485
Jumper
Setting
(pin closed)
JP2:
3-5&4-6
JP3:
1-2
JP4:
3-5 & 4-6
JP2:
1-3&2-4
JP3:
3-4
JP4:
1-3 & 2-4
JP2:
1-3&2-4
JP3:
5-6
JP4:
1-3 & 2-4
JP5: COM1 RS232 RI/+5V/+12V Power Setting
JP5 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed RI
Pin 5-6
Short/Closed +5V
JP6: COM2 RS232 RI/+5V/+12V Power Setting
JP6 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed RI
Pin 5-6
Short/Closed
+5V
All manuals and user guides at all-guides.com

INSTALLATIONS
12 MI956 User’s Manual
J10: LCD Panel Power Selection
J10 LCD Panel Power
3.3V
5V
J14: Flash Descriptor Security Overide (Factory use only)
J14 Flash Descriptor
Securit
y
Overide
Open Disabled
(Default)
Close Enabled
J22: Clear ME Contents
J22 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear ME
J23: Clear CMOS Contents
J23 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear CMOS
All manuals and user guides at all-guides.com
all-guides.com

INSTALLATIONS
MI956 User’s Manual 13
Connectors on MI956
Connector Locations on MI956........................................................... 14
CN1: COM1 and COM2 Serial Ports .................................................. 15
CN2: DVI-D and DVI-I Connector..................................................... 15
CN3: USB3.0 Connector .................................................................... 16
CN4: HDMI Connector ....................................................................... 16
CN5: Gigabit LAN (Intel 82579LM) + USB 2/3 ................................ 16
CN8: Gigabit LAN (Intel 82583V) + USB 0/1 ................................... 16
CN11: HD Audio Connector ............................................................... 16
J1: Digital I/O ...................................................................................... 17
J3: ATX Power Supply Connector ...................................................... 17
J2, J4: COM3, COM4 RS232 Serial Ports .......................................... 17
J6: ATX 12V Power Connector .......................................................... 17
JP8, JP7: LVDS Connectors (1st channel, 2nd channel)..................... 18
JP9: LCD Backlight Connector ........................................................... 18
JP10, JP11: USB Connectors .............................................................. 18
JP13: SPDIF I/O.................................................................................. 18
J24: Audio Pin Header for Chassis Front Panel .................................. 19
J26: Front Panel Connector ................................................................. 19
CN6, CN7, CN9, CN10, CN12, CN13: SATA Connectors ................ 19
CPU_FAN1: CPU Fan Power Connector............................................ 19
SYS_FAN1: System Fan1 Power Connector ...................................... 19
JP1: LPC Debug Connector (Factory use only) .................................. 20
J11: Mini-PCIE Connector .................................................................. 20
JP12: SPI Flash Connector (Factory use only).................................... 20
All manuals and user guides at all-guides.com

INSTALLATIONS
14 MI956 User’s Manual
Connector Locations on MI956
All manuals and user guides at all-guides.com

INSTALLATIONS
MI956 User’s Manual 15
CN1: COM1 and COM2 Serial Ports
[ Pin # Signal Name
RS-232 R2-422 RS-485
1 DCD TX- DATA-
2 RX TX+ DATA+
3 TX RX+ NC
4 DTR RX- NC
5 Ground Ground Ground
6 DSR NC NC
7 RTS NC NC
8 CTS NC NC
9 RI NC NC
10 NC NC NC
CN2: DVI-D and DVI-I Connector
Signal Name Pin # Pin # Signal Name
DATA 2- 1 16 HOT POWER
DATA 2+ 2 17 DATA 0-
Shield 2/4 3 18 DATA 0+
DATA 4- 4 19 SHIELD 0/5
DATA 4+ 5 20 DATA 5-
DDC CLOCK 6 21 DATA 5+
DDC DATA 7 22 SHIELD CLK
N.C 8 23 CLOCK -
DATA 1- 9 24 CLOCK +
DATA 1+ 10 C1 N.C
SHIELD 1/3 11 C2 N.C
DATA 3- 12 C3 N.C
DATA 3+ 13 C4 N.C
DDC POWER 14 C5 A GROUND2
A GROUND 1 15 C6 A GROUND3
All manuals and user guides at all-guides.com

INSTALLATIONS
16 MI956 User’s Manual
[ Signal Name Pin # Pin # Signal Name
DATA 2- 1 16 HOT POWER
DATA 2+ 2 17 DATA 0-
Shield 2/4 3 18 DATA 0+
DATA 4- 4 19 SHIELD 0/5
DATA 4+ 5 20 DATA 5-
DDC CLOCK 6 21 DATA 5+
DDC DATA 7 22 SHIELD CLK
N.C 8 23 CLOCK -
DATA 1- 9 24 CLOCK +
DATA 1+ 10 C1 N.C.
SHIELD 1/3 11 C2 N.C.
DATA 3- 12 C3 N.C.
DATA 3+ 13 C4 N.C.
DDC POWER 14 C5 N.C.
A GROUND 1 15 C6 N.C.
CN3: USB3.0 Connector
CN4: HDMI Connector
CN5: Gigabit LAN (Intel 82579LM) + USB 2/3
CN8: Gigabit LAN (Intel 82583V) + USB 0/1
CN11: HD Audio Connector
All manuals and user guides at all-guides.com