American Millenium 56512 PL User manual

P. 1
0603-E
Congratulations on owning a new American Millenium
Foosball game! We at American Millenium hope you will
have many hours of enjoyable use with this product.
WARNING: Choking Hazard -- This table contains small balls
and/or small parts. Not for children under 3 years.
!
MODEL # 56512 PL
TOOLS REQUIRED FOR ASSEMBLY:
· Phillips and Slotted Head Screwdrivers (or Power Driver) - not included
· Allen Key and Bushing Wrench - included
PARTS IDENTIFIER
#7
PLASTIC CORNER -
LEFT (2 EA)
#56512PL04
#1
SIDE APRON
(2 EA)
# 56512PL01
#2
END APRON
(2 EA)
# 56512PL02
#3
GOAL BOX BOTTOM
BOARD (2 EA)
# 56002DP36
#4
GOAL END BOARD
(2 EA)
# 56002DP03
LEG PANEL
(2 EA)
# 56512PL03
#5
PLAYFIELD
(1 EA)
# 56002DP04
#6
PLASTIC CORNER -
RIGHT (2 EA)
# 56512PL05
#8
CORNER F-CHANNEL
RIGHT (2 EA)
# 56002DP32
#10
CORNER F-CHANNEL
LEFT (2 EA)
# 56002DP31
#9
L-SHAPE LEG -
RIGHT (2 EA)
# 56512PL06
#11 #12
L-SHAPE LEG -
LEFT (2 EA)
# 56512PL07
#13
GOAL BOX
(2 EA)
# 61004DP10
#14 #15
3 PLAYER TELESCOPING ROD
- IVORY "F" (1 EA)
# 56502DP07
2 PLAYER TELESCOPING ROD
- IVORY "B" (1 EA)
# 56502DP06
(ASSEMBLED) (ASSEMBLED)
IMPORTANT!
Please Keep Your Instructions in the storage pouch provided underneath your table!
Your Model number (also located on the underside of the table) is necessary should you
need to contact us. Before attempting assembly, please read through this instruction book
to familiarize yourself with all the parts and assembly steps. We recommend that two adults
assemble this game. Please refer to the Parts Identier below and be sure that all parts have
been included. Although we at American Millenium are dedicated to giving our customers
the best product possible, occasionally a part may be missing. If you are missing a part, or
if you have any questions, please call our Consumer Service department at 1-800-526-0244
between the hours of 9:00 a.m. and 5:00 p.m. Eastern Standard Time.
Do not return the game to the store. Please contact us rst at 1-800-526-0244, or fax your
request to us at: 1-973-347-1541.

P. 2
5 PLAYER TELESCOPING ROD
- IVORY "D" (1 EA)
# 56502DP08
#16 #17 #18 #19 #20
PLAYER
(IVORY) (13 EA)
# 56502DP12
PLASTIC WASHER
(16 EA)
# 27093DP21
#26 #27
5" BELL STYLE LEG
LEVELER (4 EA)
# 35087DP13
#28
RUBBER BUMPER
(16 EA)
# 56002DP24
#29 #30
SPANNER
(1 EA)
# 35076DP21
HAND GRIP
(8 EA)
# 27093DP23
PLAYER
(BLACK) (13 EA)
# 56002DP18
#21 #22
2 HOLE TELESCOPING
PLAYER ROD (2 EA)
# 56002DP19
#23
3 HOLE TELESCOPING
PLAYER ROD (2 EA)
# 56002DP20
#24 #25
PLAYER MOUNTING
BLOT (52 EA)
# 35076DP16
5 HOLE TELESCOPING
PLAYER ROD (2 EA)
# 56002DP21
SLIDE SCORER
(BLACK) (2 EA)
# 35012DP16
#31
(ASSEMBLED) (PRE-ASSEMBLED)(ASSEMBLED) (ASSEMBLED)
2 PLAYER TELESCOPING ROD
- BLACK "G" (1 EA)
# 56002DP14
3 PLAYER TELESCOPING ROD
- BLACK "C" (1 EA)
# 56002DP15
5 PLAYER TELESCOPING ROD
- BLACK "E" (1 EA)
# 56002DP16
(ASSEMBLED)
(PRE-ASSEMBLED)
#32
3.5 X 25MM FLAT
HEAD SCREW (4 EA)
# 32093DP05
#33
FIELD SUPPORT BRACE
(3 EA)
# 56002DP25
#34 #35
5MM ALLEN KEY
(1 EA)
# 34097DP10
F - CHANNEL
(2 EA)
# 61004DP25
(PRE-INSTALLED)
BALL BUSHING - A
(8 EA)
# 35086PL03
#36 #37
BALL BUSHING - B
(8 EA)
# 61004DP12
#38
BALL RETURN TRAY
(2 EA)
# 35067DP13
#39 #40
STEEL SUPPORT ROD
(3 EA)
# 35086PL14
NAME PLATE
(2 EA)
# 56501DP09
(PRE-INSTALLED)
ACORN NUT
(6 EA)
# 35086PL15
#41 #42
BALL ENTRY CUP
(2 EA)
# 35012DP22
#43
SOCCER BALL
(WHITE) (2 EA)
# 56001DP25
#44 #45
8 X 60MM ALLEN KEY
BOLT (16 EA)
# 35046DP28
6 X 45MM ALLEN KEY
BOLT (24 EA)
# 97057DP12
#46
22MM FLAT WASHER
(16 EA)
# 35067DP21
(PRE-INSTALLED)
(PRE-ASSEMBLED) (PRE-ASSEMBLED) (PRE-ASSEMBLED) (PRE-ASSEMBLED)
(PRE-ASSEMBLED)
(PRE-INSTALLED)
#47
18MM FLAT WASHER
(24 EA)
# 27093DP28
#48
3.5 X 10.5MM WASHER
HEAD SCREW (14 EA)
# 35067DP16
#49 #50
3.5 X 12MM WASHER
HEAD SCREW (24 EA)
# 56002DP26
3.5 x 12MM ROUND
HEAD SCREW (4 EA)
# 56002DP27
GOAL BOX BOARD -
LEFT (2 EA)
# 56002DP35
#51 #52
GOAL BOX BOARD -
RIGHT (2 EA)
# 56002DP34
#53
BUSHING WRENCH
(1 EA)
# 35086PL13
#54
SOCCER BALL
(ORANGE) (2 EA)
# 56001DP24
(PRE-ASSEMBLED)
#55
6 X 45MM ALLEN KEY
BOLT - SILVER (8 EA)
# 56512PL18

P. 3
FIG. 1
47
51
52
4
1
34
46
47
46 35
4
51
52
SILICONE
www.sportcraft.com
ASSEMBLY INSTRUCTIONS:
We recommend that two adults work together to assemble this game.
1) Open the carton of your new Foosball Game near where you will play. Select a clear level oor. The table will
be assembled upside down and then turned over onto its legs. This is a very heavy game and turning it over
will require at least Two Strong Adults.
2) Remove all the contents from inside the carton and verify that you have all listed parts as shown on the Parts
Identier. NOTE: Some parts are pre-installed and the Player Rods are pre-assembled. We suggest that
you use the bottom carton as a clean at work area to protect the game. Carefully cut or tear the four carton
corners so that the bottom is now your work area.
FIG. 1
3) Using one Side Apron (#1) with the top edge up and the pre-installed F-Channel (#34) facing inward, attach
the two Goal End Boards (#4) to each end of the Side Apron (#1) as shown in Fig. 1. Secure using two of
the 6 x 45mm Allen Key Bolts (#46) and two of the 18mm Flat Washers (#47) for each Goal End Board (#4)
using the Allen Key (#35).
4) Attach one Left (#51) and one Right (#52) of the Goal Box Boards, with the grooves facing inward, to the
installed Goal End Board (#4) using four of the 6 x 45mm Allen Key Bolts (#46) and four of the 18mm Flat
Washers (#47) as shown in Fig. 1. NOTE: The bolts pass through the washer, through the Goal End Board
and then into the Goal Box Boards.
5) Repeat step 4 to attach the other Goal End Board (#4) and Goal Box Boards (#51 and #52) to the other end
of the Side Apron (#1). See Fig. 1.
#56
SILICONE
(1 EA)
# 35086PL20
#57 #58 #59 (ASSEMBLED)
3 HOLE SOLID
GOALIE ROD (2 EA)
# 56512PL08
3 PLAYER GOALIE ROD
ASSEM
BLY - BLACK
"H" (1)
# 56512PL10
3 PLAYER GOALIE ROD
ASSEM
BLY
- IVORY "A" (1)
# 56512PL09
(ASSEMBLED)
(PRE-ASSEMBLED)
18MM FLAT WASHER
- SILVER (8 EA)
# 56002LDP23
#60

P. 4
FIG. 4
7
8
9
10 8
6
7
49
46
2
6
47
35
FIG. 2
3
46
1
47
46
3
2
35
FIG. 3
FIG. 4
12) Place the two Left Corner F-Channels (#9)
and the two Right Corner F-Channels (#10)
into the four corners of the table as shown in
Fig. 4.
13) Install the two Plastic Corners - Left (#7) and
the two Plastic Corners - Right (#8), using
six of the 3.5 x 12mm Washer Head Screws
(#49) per corner. See Fig. 4.
NOTE: Make sure all corners t the Side Aprons
(#1) and End Aprons (#2).
FIG. 3
9) Slide the Playeld (#6), with the graphics facing up into the F-Channels (#34) as shown in Fig. 3. If the
Playeld does not slide smoothly, check to be sure that you have not over tightened the connecting bolts
(#46).
10) Repeat step 8 to attach the other
End Apron (#2). NOTE: Be sure the
Playeld is into the grooves of the
End Apron (#2). See Fig. 3.
11) Now go back and tighten all the
Cabinet Bolts (#46) using the Allen
Key (#35) that attach the Goal
Boards, End Aprons and Side
Aprons.
FIG. 2
6) Now attach the other Side Apron (#1) with the nished edge facing up and the F-Channel (#34) facing inward,
to the Goal End Boards using four of the 6 x 45mm Allen Key Bolts (#46) and four of the 18mm Flat Washers
(#47) using the Allen Key (#35). See Fig. 2. Do not tighten the bolts securely at this time.
7) Slide the two Goal Box Bottom Boards (#3) into the grooves of the Goal Box Boards as shown in Fig. 2.
8) Next, attach one End Apron (#2), to
the Left (#51) and Right (#52) Goal
Box Boards at one end using four
of the 6 x 45mm Allen Key Bolts
(#46) and four of the 18mm Flat
Washers (#47). Secure with the
Allen Key (#35) See Fig. 2.

P. 5
FIG. 6
27
12
55
44
56
5
11
11
12
44
5
45
45
FIG. 5
FIG. 5A
438
48
1
40
41 47
33 33 33
38
HOLD TABLE
CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE
TABLE ON ITS LEGS!
CAUTION: Two strong adults are recommended to ip the
table as shown.
1. Lift the table of the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
FIG. 6
16) Attach one Right Leg (#11) and one Left (#12) L-Leg using four of the 8 x 60mm Leg Bolts (#44) and four
of the 22mm Flat Washers (#45) for each leg as shown in Fig. 6. Now do the same for the Legs at the other
end of the table. Do not tighten the bolts securely at this time.
17) Attach one Leg Panel (#5) to one Right and Left L-Leg using four of the Silver 6 x 45mm Allen Key Bolts
(#55) and four of the Silver 18mm Flat Washers (#56) per panel as shown in Fig. 6. Repeat this step for the
other Leg Panel. Now go back and tighten all the bolts.
18) Locate the four Leg Levelers (#27) and
screw one Leg Leveler into each leg.
19) Left the table assembly from the oor
with two strong adults, turn it over, and
set the table on its legs in the location
where you will play. Now go back and
make sure that all connections are
tight.
FIG. 5
14) Next, with two adults, turn the table cabinet upside down and place the Field Support Braces (#33) on the
Playeld (#6) with the grooves facing up as shown in Fig. 5. Insert the Steel Support Rods (#40) through
the holes in the Side Aprons and through the groove in the Field Support Brace (#33). Use one 18mm Flat
Washer (#47) and one Acorn Nut (#41) to secure each end of the Steel Support Rod to the Side Aprons.
Repeat this step for each Support Brace and then go back and tighten all the connections securely.
15) Attach one end of the Ball Return Tray (#38) to
the Goal End Board using four of the 3.5 x 10.5
Washer Head Screws (#48) as shown in Fig. 5A.
Then attach the other end of the Ball Return Tray to
the Side Apron (#1) using three of the 3.5 x 10.5mm
Washer Head Screws (#48). NOTE: Pilot holes
show the proper screw placement. Repeat this step
to attach the other Ball Return Tray (#38) at the
opposite end of the table.

P. 6
7
FIG. 8
FIG. 9A FIG. 9B FIG. 9C
1
2
1
142
FIG. 7
13
31
50 32 31
39
30
37
1
53
36
1
36
37
36
FIG. 9D
FIG. 8
22) Install the back half of one Ball Entry Cup (#42) from the
inside of the Side Apron (#1) and install the front half of the
Ball Entry Cup from the outside of the Side Apron and twist
both halves together. See Fig. 8.
FIG. 9
23) To install the Player Rods, follow the steps as shown in Fig 9, 9A, 9B, 9C and 9D. Begin by removing the
outer half of the Ball Bearing Bushings - A (#36) using the Bushing Wrench (#53) as shown in Figures 9A
and 9D. Slide the end of the Player Rods (A through H) into the inner half of the Ball Bearing Bushings - A
(#36) as shown in Fig. 9A.
24) Next, put the other end of the rod through the other side of the table's inner Bushing - B (#37). See Fig. 9B.
Make sure that the Player Rods are installed properly. The players should have thier backs facing their own
goal. (The BACK of the robo player has a star-shaped cut-out.) The players for each team must be facing
the same direction. See Fig. 9.
FIG. 7
20) Place one Goal Box (#13) on the Playeld (#6) and attach it the the End Apron (#2) using two of the 3.5
x 12mm Round Head Screws (#50). See Fig. 7. Repeat the same to attach the other Goal Box (#13) to the
other End Apron.
21) Install one of the Bead Scorers (#31) at the center on the top of the Goal Box (#13) using two of the 3.5
x 25mm Flat Head Screws (#32) as shown in Fig. 7. Pilot holes show the proper screw placement. Do the
same for the other Goal Box and Scorer (#50) at the other end.
REMOVE OUTER
BUSHINGS
REINSTALL OUTER
BUSHINGS

P. 7
FIG. 9
37
36
A
E
D
C
B
GH
F29
Mt. Olive, NJ 07828
GAME RULES:
1. To start play, ip a coin to see which team or player will serve rst. To begin, serve the ball through the side entry cup.
2. Press and score by pushing and pulling rods and twisting grips. Spinning the rods is considered illegal in tournament
play. If playing as teams (more than two players total), once the ball is served, players may not change position on
the rods until: one team scores; a team requests a time out (maximum 2 per game); the ball must be served again; or
between games.
3. A point is scored when the ball enters the goal. A serve, by the team last scored upon, follows each goal. Teams change
table sides after each game.
4. Intentional jarring or tipping of table during play is illegal, and reaching into the playing area during play is illegal (except
for a dead ball).
5. A ball is considered a DEAD BALL when it has completely stopped its motion or is unreachable by any player. If a ball
stops between the goal and the two-man rod, then it is put back into play by placing it in the corner that is nearest the
dead ball spot. If the ball completely stops anywhere else on the playeld between both two-man rods, it is put back into
play with a serve by the team which originally served the ball.
6. If a ball leaves the playing area during play (other than through the goals), the ball is considered OUT OF PLAY. The ball
is returned to play with a serve by the team which originally served the ball.
7. This game is meant to be played with either two or four players. We recommend that all others should stand clear of the
table playing area if they are not playing.
TABLE MAINTENANCE:
1. TABLE: Keep your table covered. If there is dust on the playeld or the aprons, use a vacuum or wipe with a clean, soft
cloth to remove. Do not sit on the table and do not use the table outside.
2. RODS: Make sure that the bolts and screws on the players are tight. Occasionally wipe the rods with a clean, soft cloth.
Never lift the table by the rods. Do not spin the rods too aggresively, as this may cause damage. We recommend the
use 100 % silicone to lubricate the bushings, from the outside of the game so as not to drip onto the playeld.
3. LEGS: Check that the leg bolts are tight. When moving the table, lift the table off of its legs and place it down squarely
on the legs, do not drag the table (and do not lift by the rods).
IMPORTANT!
EACH TEAM SHOULD BE HEAD
DOWN AND THEIR BACKS
FACING THIER OWN GOAL.
25) Place the outer Ball Bushing - B (#37) on the rod from the outside of the table and screw it into place using
the Spanner (#30) tool. See Figures 9B and 9C. Then go back and reinstall the outer Ball Bearing Bushing
- A (#36) using the Bushing Wrench (#53). See Fig. 9D.
26) Put the Hand Grips (#29) in the rods in order as shown in Fig. 9. The Hand Grips go on the ends of the Rods
with holes in them. NOTE: To make the handles easier to attach, spray a little window cleaner on the rod
ends prior to installation and tap on them gently with a hammer.

LIMITED WARRANTY
Limited Warranty
American Millenium (the “Company”) warrants the Product to be free from defects in workmanship and materials under
normal use and conditions FOR A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE in the United
States and Canada.
Product Registration Card
The Product Registration Card must be lled out completely and mailed to the Company at the address printed on the card
within 10 days from the date of your purchase of the Product.
What Is Covered
Except as provided below, this Limited Warranty covers all defects in materials and workmanship. This Limited Warranty
is void if the Product is:
• Damaged through improper usage, negligence, misuse, abuse, transportation damage, acts of nature, or accident
(including failure to follow the instructions supplied with the Product)
• Used in commercial applications or rentals
• Modied or repaired by anyone not authorized by the Company.
What Is Not Covered
This Limited Warranty does not cover expendable items such as batteries, light bulbs, fuses, accessories, cosmetic parts
and other items that wear out due to normal usage.
What The Company Will Pay For
If during the one year Limited Warranty period, any part or component of the Product is found by the Company to be
defective, the Company will repair or, at its option, will replace with a new Product (either the same or an equivalent model)
without charge for labor or parts. The Company’s obligation to repair or replace the Product, however, shall be limited to
the original purchase price of the Product.
How To Obtain Warranty Service
In order to enforce your rights under this Limited Warranty, you must follow these procedures:
• You must have completed and mailed the Product Registration Card to the Company within 10 days of purchase of the
Product.
• You must include THE ORIGINAL COPY OF YOUR SALES RECEIPT.
• You must call the Company’s Consumer Service Department at 1-800-526-0244 from 9:00 A.M. to 5:00 P.M. (EST)
to notify the Company of the nature of the problem and to obtain instructions for how to obtain servicing. At the
Company’s option, the Product may be serviced at your location or at a location designated by the Company.
• If you are instructed to return the Product to the Company for servicing, you are responsible for shipping the Product,
at your expense, to the address designated by the Company in packaging that will protect against further damage.
• You must also include your name, address, daytime telephone number, model number of the Product and a description
of the problem.
• The Company will pay for any shipping charges to return the repaired or replaced Product to you.
THIS LIMITED WARRANTY IS AVAILABLE ONLY TO THE ORIGINAL PURCHASER OF THE PRODUCT AND IS VALID
IN THE UNITED STATES AND CANADA ONLY.
THE COMPANY’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR DO NOT ALLOW
FOR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. TO THAT EXTENT, THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
This Limited Warranty gives you specic legal rights, but you may also have other rights that vary from state to state.
If you have questions regarding this Limited Warranty or the operation of the Product, you may call or write us:
Consumer Service Department
313 Waterloo Valley Rd.
Mt. Olive, NJ 07828
1-800-526-0244 1102
**NOTE: Please save your original proof of purchase as it is needed should you require warranty service.

56512PL01
56512PL02
56002DP36
56002DP03
56512PL03
56002DP04
56512PL04
56512PL05
56002DP31
56002DP32
56512PL06
56512PL07
61004DP10
56502DP06
56502DP07
56502DP08
56002DP14
56002DP15
56002DP16
56502DP12
56002DP18
56002DP19
56002DP20
56002DP21
35076DP16
27093DP21
35087DP13
56002DP24
27093DP23
35076DP21
35012DP16
32093DP05
56002DP25
61004DP25
34097DP10
35086PL03
61004DP12
35067DP13
56501DP09
35086PL14
35086PL15
35012DP22
56001DP25
35046DP28
35067DP21
97057DP12
27093DP28
35067DP16
56002DP26
56002DP27
56002DP35
56002DP34
35086PL13
56001DP24
56512PL18
56002LDP23
35086PL20
56512PL08
56512PL09
56512PL10
00001HG05
00001HG06
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
0603-E
Side Apron
End Apron
Goal Box Bottom Board
Goal End Board
Leg Panel
Playeld
Plastic Corner - Left
Plastic Corner - Right
Corner F - Channel - Left
Corner F - Channel - Right
L-Leg - Right
L-Leg - Left
Goal Box
2 Player Telescoping Assembly - Ivory
3 Player Telescoping Assembly - Ivory
5 Player Telescoping Assembly - Ivory
2 Player Telescoping Assembly - Black
3 Player Telescoping Assembly - Black
5 Player Telescoping Assembly - Black
Player (Ivory)
Player (Black)
2 Hole Telescoping Player Rod
3 Hole Telescoping Player Rod
5 Hole Telescoping Player Rod
Player Mounting Bolt
Plastic Washer
5" Bell Style Leg Leveler
Rubber Bumper
Hand Grip
Spanner
Slide Scorer (Black)
3.5 x 25mm Flat Head Screw
Field Support Brace
F - Channel
5mm Allen Key
Ball Bushing - A
Ball Bushing - B
Ball Return Tray
Name Plate
Steel Support Rod
Acorn Nut
Ball Entry Cup
Soccer Ball (White)
8 x 60mm Allen Key Bolt
22mm Flat Washer
6 x 45mm Allen Key Bolt
18mm Flat Washer
3.5 x 10.5 Washer Head Screw
3.5 x 12mm Washer Head Screw
3.5 x 12mm Round Head Screw
Goal Box Board - Left
Goal Box Board - Right
Bushing Wrench
Soccer Ball (Orange)
6 x 45mm Allen Key Bolt - Silver
18mm Washer - Silver
Silicone
3 Player Goalie Telescoping Rod
3 Player Goalie Telescoping Assembly - Ivory
3 Player Goalie Telescoping Assembly - Black
Optional Accessories:
Table Cover
Table Cover w/ Kit (extra balls and silicone)
11.00 ea
8.00 ea
2.00 ea
6.00 ea
8.00 ea
17.00 ea
3.00 ea
3.00 ea
2.00 ea
2.00 ea
6.00 ea
6.00 ea
2.00 ea
12.00 ea
13.00 ea
14.00 ea
12.00 ea
13.00 ea
14.00 ea
2.00 ea
2.00 ea
6.00 ea
6.00 ea
6.00 ea
0.50 ea
0.50 ea
5.00 ea
0.50 ea
2.00 ea
0.50 ea
3.00 ea
0.50 ea
2.00 ea
2.00 ea
3.00 ea
2.00 ea
2.00 ea
3.00 ea
1.00 ea
2.00 ea
0.50 ea
2.00 ea
2.00 ea
0.50 ea
0.50 ea
0.50 ea
0.50 ea
0.50 ea
0.50 ea
0.50 ea
2.00 ea
2.00 ea
1.00 ea
2.00 ea
0.50 ea
0.50 ea
8.00 ea
6.00 ea
13.00 ea
13.00 ea
40.00 ea
50.00 ea
PARTS RE-ORDER FORM
# 56512 PL - FOOSBALL
REF QUANTITY
ORDERED PART # DESCRIPTION UNIT
PRICE
TOTAL
AMOUNT
Subtotal:
NJ (6%) and IL (6.25%) Residents Add State Sales Tax:
Shipping and Handling Charges:
TOTAL: $ 6.00 US
NAME: ______________________________________________ DATE: ____________________
ADDRESS: ______________________________________________ PHONE: ____________________
CITY: _________________________________ STATE: ______________ ZIP CODE: __________
**PRICES SUBJECT TO CHANGE WITHOUT NOTICE
Send this form along with your
check or money order payable to:
Sportcessories
313 Waterloo Valley Road
Mt. Olive, NJ 07828