American Standard DELANCEY 4279.300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965796 Rev. 1.0 (11/18)
DELANCEY™
Single Control Kitchen Faucet
With Pull Down Spray
INSTALLATION
INSTRUCTIONS
4279.300
Certied to comply with ANSI A112.18.1M
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION Turn off water at
main supply
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver
SINK OR
MOUNTING
SURFACE
7
7
9
PUTTY
SPOUT BASE SPOUT BASE
2
3
4
5
8
6
74
5
8
7
6
9
3
2
A (OPTIONAL) B
1
• (A) Installation with ESCUTCHEON (1). (Escutcheon is not supplied with base product). Apply a bead of putty to bottom
edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert
SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting
surface. Follow mounting instructions below to secure faucet to mounting surface.
• (B) Installation less ESCUTCHEON (1). Make certain the SEAL (9) is properly seated in recess of spout base. Insert supply
HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting hole and seat spout base onto sink or mounting surface.
Do not use putty.
• Insert HOSES (2) through RUBBER
WASHER (4), BRASS WASHER (5),
and threaded LOCKNUT (6).
• Assemble RUBBER WASHER (4),
BRASS WASHER (5), and threaded
LOCKNUT (6) onto SHANK (3)
from underside of sink or
mounting surface. Hand
tighten LOCKNUT (6).
• Use a screwdriver to tighten
SCREWS (8) on LOCKNUT (6).
Work your way around
LOCKNUT (6), tightening
the screws slightly each
time until all are snug
to ensure even pressure.

- 2 -
2
M965796 Rev. 1.0 (11/18)
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 21"long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE & INSTALL WEIGHT
4CHECK CONNECTIONS FOR LEAKS
• Move HANDLE into “off” position.
• Turn on water supplies and check
connections for leaks.
• Operate HANDLE up and down, left
and right to ushwater lines thoroughly.
• Operate HAND SPRAY and
check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
• Push the SPRAY HOSE END (2) into the HOSE CONNECTOR (1)
slide down LOCKING COLLAR (3) until it snaps into place
to secure connection.
• With HAND SPRAY (4) seated in SPOUT (5), install WEIGHT (7)
onto HOSE (6) 21 inches from the underside of the sink deck
and secure with SCREW (8).
• With one weight, spray will retract and dock potentially
requiring slight assistance.
7
6
8
2
1
3
4
5

- 3 -
6
7
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
5
M965796 Rev. 1.0 (11/18)
SPRAY OPERATION
• With FAUCET on press TOGGLE
BUTTON (4) on SPRAY (3) to
switch from stream to spray.
• Press and hold PAUSE BUTTON (5)
to temporarily stop ow from
SPRAY (3). Release PAUSE
BUTTON (5) to resume ow
fromSPRAY (3).
SERVICE
TEST INSTALLED FAUCET
• Move HANDLE (1) into “off” position.
• Turn on water supplies.
• Check connection for leaks.
(See Section 4)
• With HANDLE (1) in “off” position,
unthread SPRAY (3) from HOSE (2).
• Operate handle back to front, in
COLD and HOT positions, to ush
water lines thoroughly.
• Replace SPRAY (3) onto HOSE (2).
1
3
2
REMOVE
ON
OFF
COLD
HOT
STREAM
(AERATOR)
SPRAY
5
3
4
3
4
5
5a
2
1
8
6
7
If faucet drips, operate HANDLE several times
from “off” to “on.” Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may
cause reduced flow.
To clean, rst turn off water supply then:
• Loosen HANDLE SCREW (1) and remove
HANDLE (2).
• Unthread ESCUTCHEON CAP (3) and
ADAPTER (8). Unthread three
MOUNTING SCREWS (4).
• Lift CARTRIDGE (5) off MANIFOLD (6)
and remove CARTRIDGE SEALS (7).
• Clean MANIFOLD (6), CARTRIDGE (5)
ports and SEALS (7).
• Place SEALS (7) into CARTRIDGE
PORTS (5a).
• Place CARTRIDGE (5) onto
MANIFOLD (6) tighten ADAPTER (8)
and tighten MOUNTING SCREWS (5)
alternately.
• Replace ESCUTCHEON CAP (4),
HANDLE (2), tighten HANDLE
SCREW (1).

- 4 - M965796 Rev. 1.0 (11/18)
MODEL NUMBER
4279.300
DELANCEY™
Single Control Kitchen
Faucet With Pull
Down Spray
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M911793-0070A
Seal
M962146-0070A
Mounting Kit
M951483-0070A
Cartridge
M918511-0070A
Cartridge Screws
M907315-YYY0A
Escutcheon Cap
M950374-YYY0A
Spray Assembly
M970094-0070A
Weight
M970238-YYY0A
Handle Kit
M970223-0070A
Set Screw
M950415-0070A
Hand Spray Hose
1660152.XXX
Escutcheon Kit
(Optional)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
POLISHED NICKEL 013
LEGACY BRONZE 278
STAINLESS STEEL 075