American Standard 0621.001 STUDIO User manual

5
SAVE FOR FUTURE USE
7301244-100
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2008
NOTE: Pictures may not exactly define contour of china and components.
ABOVE COUNTER SINK
FOR USE WITH: 0621.001 STUDIO
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Drill Tape Measure
Hacksaw Phillips Screwdriver Pipe Wrench Basin Wrench Channel Lock Pliers
Tubing Cutter Jig Saw Silicone Adhesive Plumber’s Putty or Caulking
RECOMMENDED FAUCET*: 2064.101 ONE lavatory faucet
*Log on to www.americanstandard-us.com for additional faucet selections.
Countertop Installation:
Using the template provided, locate the position of
the sink on the countertop. Provide proper clearance
under the countertop for the faucet supply lines, drain
assembly and the structural parts of the cabinet.
NOTE: If replacing an existing sink be certain to shut
off water supply before removing old sink.
Drill a clearance hole inside the perimeter line
of the template for countertop installation.
Cut opening around the perimeter of the template.
Mount the faucet and drain assembly (not included)
on the sink following the manufacturer’s instructions.
Be certain to apply a bead of sealing putty on the
underside of the drain (Part “A”) in order to ensure a
watertight seal between the sink and drain. Remove
excess putty after installing drain on sink.
4a
4b
Countertop Installation:
• Place the sink temporarily into the template
• Check for alignment and clearance
• Mark the sink and countertop in several places
as a guide for the installation location.
Vanity Installation:
• Place the sink temporarily on the vanity to
check for alignment and clearance
• The sink should be centered left to right on the
vanity with the front edge of the sink even with
the front of the vanity
After checking fit and alignment, turn sink upside down
and apply a generous portion of silicone adhesive
around the under side of the rim near the edge. Place
sink in position. Wipe off excess adhesive.
Mounting on Studio 22" Vanity:
Assemble vanity as per instructions.
1a
1b
2
3
Perimeter
of
template
Perimeter of
template
A

B
C
2
67
7301244-100
Connect trap to drain assembly hand tight to check
alignment. It may be necessary to cut off part of the
tailpiece (area “B”) or part of the horizontal leg of the
trap (area “C”). Secure joints for watertight assembly.
Connect supply line to faucet (finger tight) and
carefully bend tubes to engage with the supply
shut-off valves. Tighten connections at faucet
and shut-off valves for secure seal.
Shut-Off Valves
For residents of the United States, warranty
information may also be obtained by calling the
following toll free number: [phone]
www.americanstandard-us.com
In the United States:
American Standard, Inc.,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
In Canada:
American Standard,
2480 Stanfield Rd.,
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com/mx
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (”American Standard”) plumbing product, within one year after its initial purchase,
confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the
product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited
warranty claim, proof of purchase will be required—save sales receipt.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the
purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before
installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to
faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American
Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American
Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other
costs of removal or installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR
OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT LIMITED TO, TILES, MARBLE ETC.
American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect
or to the repair or exchange of a defective product, all of which are expressly excluded from this limited warranty. This
limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly
disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including those of
merchantability or fitness for an intended purpose. (Some states or provinces do not allow the exclusion or limitation of
implied limited warranties, so this exclusion may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from
province to province, in which case this limited warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom
the product was purchased, or that a service request (including a description of the product model and of the defect) be sent
to the following address: