American Standard Neo Modern FFAS0703 Installation instructions

Rev. A1 - 1 -
- 4 -
FFAS0703-102500BF0
Single Hole Vessel Mixer W/o PUW
Installation &
Operation Instructions
Dimension
Recommended Tools and Materials
* Recommended water pressure condition: 0.1~0.5Mpa.
* Environment Temperature:1~55℃
* Steam is not allowed to use.
Conditions for use
*Remove all impurity in pipes before beginning to avoid clogging. Connect faucet pipes correctly.
* Check installation distances in the Dimension diagram to ensure correct installation.
When in the process of installation, grab the whole body. Do not grab handle only.
Pre-Installation Checks
* American Standard always keep raising and improving the product design and performance, and reserve the right to modify
the dimension and spefication. At this case, we will not inform you separately.
* This installation instruction sheet is for your reference only, the dimension and specification is subject to the actual products.
Thank you for selecting American-Standard - the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
All instruction procedures must comply in strict accordance with applicable local plumbing and building codes
Adjustable Wrench Tape Measure
Term of Guarantee
Attention:
Please leave the manual with the customer
after installation is finished
Care & Maintenance
If you want to change the parts or clean the inner of faucet, please follow the steps in the above
to remove the parts, then proceed the next steps.
* One year for "O" rings or washers. Five years for Chrome plate Body of tap or faulty workmanship
Lifetime drip free warranty on Cartridge.
* Except:
-Trouble caused by disasters or user's carelessness.
-If leakage is caused by connection problem with 3rd party products or non approved parts.
Neo Modern
Neo Modern
Installation Hole
35
42
260
143
146
15
237
50
Max35
360 300
1
2
3
5
Aerator
Clean Water
Remove all impurity in Aerator
Soft Brush
4
62.5mm
Unit:mm

- 2 - - 3 -
Parts List Installation
Installation
ON
1
2
Test / Usage
* Move handle down into “OFF”position. Turn on supply angle valve to check allconnections for leak.
* Operate handle up and down, left and right to flush water lines thoroughly.
Test
Usage
Trouble Shooting Guide
Untwist the hose.
Cartridge packing
Hose junction Check the connection.
Check cartridge install.
Check valve position.
Check any impurities. Remove all impurities.
Open it to full valve
When packing is damaged, replace the cartridge.
Check the existence of packing and wind it up sufficiently
Poor flow rate
Leakage
Angle valve
Flexible hose
Regulator
Check if hose is twisted.
Check if the water from Supply valve is enough or not Increase water supply
Deviant
Temperature
Supply Valve
Trouble
Checkpoint
Contents Action
Cold
Hot
No. Part Name Q’ty
Parts List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Index Button
Screw
Handle
Cap
Nut
Cartridge
Body
Aerator
Pipe
Escutcheon
Washer
Washer
Washer
Shank
Nut
Hose(Red)
Hose(Blue)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
15
16
17
14
1
2
Water Supply Pipeline
(Hot)
* Consult the dimension drawing and lay the pipes.
* Wash and clean the water supply pipeline.
Water Supply Pipeline
(Cold)
Water Supply Valve
(Provided by user)
1
2
34
Installation Hole
Hose(Red)
Hose(Blue)
Water Supply Valve
(Hot)
Water Supply Valve
(Cold)